2011 INFINITI QX56 relay

BCS
BCM
BCS-57
< ECU DIAGNOSIS INFORMATION >
C
D E
F
G H
I
J
K L
B A
O P
N
DTC IndexINFOID:0000000006274822
NOTE:
The details of time display are as follows.
 CRNT: A malfunction is detected now.
 PAST: A malfunction was detected in the past.
IGN counter is displayed on Freeze Frame Data. For details of Freeze Frame Data, refer to
BCS-14, "
COM-
MON ITEM : CONSULT-III Function (BCM - COMMON ITEM)".
4 B2013: ID DISCORD BCM-S/L
 B2014: CHAIN OF S/L-BCM
 B2555: STOP LAMP
 B2556: PUSH-BTN IGN SW
 B2557: VEHICLE SPEED
 B2601: SHIFT POSITION
 B2602: SHIFT POSITION
 B2603: SHIFT POSI STATUS
 B2604: PNP/CLUTCH SW
 B2605: PNP/CLUTCH SW
 B2608: STARTER RELAY
 B2609: S/L STATUS
 B260B: STEERING LOCK UNIT
 B260C: STEERING LOCK UNIT
 B260D: STEERING LOCK UNIT
 B260F: ENG STATE SIG LOST
 B2612: S/L STATUS
 B2614: BCM
 B2615: BCM
 B2616: BCM
 B2618: BCM
 B2619: BCM
 B261A: PUSH-BTN IGN SW
 B26E9: LOCK MALFUNCTION
 B26EF: STRG LCK RELAY OFF
 B26F0: STRG LCK RELAY ON
 B26F1: IGN RELAY OFF
 B26F2: IGN RELAY ON
 B26F3: START CONT RLY ON
 B26F4: START CONT RLY OFF
 B26F5: STRG LCK STS SW
B26F6: BCM
B26F7: BCM
B26F8: BCM
 B26F9: CRANK REQ CIR SHORT
 B26FA: CRANK REQ CIR OPEN
 B26FC: KEY REGISTRATION
 U0415: VEHICLE SPEED
5  B2621: INSIDE ANTENNA
 B2622: INSIDE ANTENNA
 B2623: INSIDE ANTENNA
6  B2626: OUTSIDE ANTENNA
 B2627: OUTSIDE ANTENNA
 B2628: OUTSIDE ANTENNA
7 B26E7: TPMS CAN COMM
Priority DTC
Revision: 2010 May2011 QX56

BCS-58
< ECU DIAGNOSIS INFORMATION >
BCM
CONSULT display Fail-safeFreeze Frame Data
Vehicle Speed
Odo/Trip Meter
Vehicle Condition Intelligent Key warn-
ing lamp ON Reference
page
No DTC is detected.
further testing
may be required. ————
U1000: CAN COMM — — — BCS-70
U1010: CONTROL UNIT (CAN) — — —BCS-71
U0415: VEHICLE SPEED×— ×BCS-72
B2013: ID DISCORD BCM-S/L ××× SEC-69
B2014: CHAIN OF S/L-BCM××× SEC-70
B2192: ID DISCORD BCM-ECM×—— SEC-60
B2193: CHAIN OF BCM-ECM ×—— SEC-61
B2195: ANTI-SCANNING ×—— SEC-62
B2196: DONGLE NG ×—— SEC-63
B2198: NATS ANTENNA AMP ×—— SEC-65
B2555: STOP LAMP — ××SEC-73
B2556: PUSH-BTN IGN SW — ××SEC-76
B2557: VEHICLE SPEED ××× SEC-78
B2562: LOW VOLTAGE — ×—BCS-73
B2601: SHIFT POSITION ××× SEC-79
B2602: SHIFT POSITION××× SEC-82
B2603: SHIFT POSI STATUS××× SEC-85
B2604: PNP/CLUTCH SW××× SEC-89
B2605: PNP/CLUTCH SW××× SEC-91
B2608: STARTER RELAY××× SEC-93
B2609: S/L STATUS××× SEC-95
B260B: STEERING LOCK UNIT××× SEC-98
B260C: STEERING LOCK UNIT — ××SEC-99
B260D: STEERING LOCK UNIT ××× SEC-100
B260F: ENG STATE SIG LOST××× SEC-101
B2612: S/L STATUS××× SEC-102
B2614: BCM — ××PCS-56
B2615: BCM — ××PCS-59
B2616: BCM — ××PCS-61
B2618: BCM — ××PCS-63
B2619: BCM ××× SEC-105
B261A: PUSH-BTN IGN SW — ××PCS-64
B2621: INSIDE ANTENNA — ×—DLK-104
B2622: INSIDE ANTENNA — ×—DLK-106
B2623: INSIDE ANTENNA — ×—DLK-108
B2626: OUTSIDE ANTENNA — ×—DLK-110
B2627: OUTSIDE ANTENNA — ×—DLK-112
B2628: OUTSIDE ANTENNA — ×—DLK-114
B26E7: TPMS CAN COMM — — — BCS-74
Revision: 2010 May2011 QX56

BCS
BCM
BCS-59
< ECU DIAGNOSIS INFORMATION >
C
D E
F
G H
I
J
K L
B A
O P
N
B26E9: LOCK MALFUNCTION —
××
(Turn ON for 15 sec-
onds) SEC-106
B26EF: STRG LCK RELAY OFF
××× SEC-107
B26F0: STRG LCK RELAY ON××× SEC-109
B26F1: IGN RELAY OFF××× PCS-66
B26F2: IGN RELAY ON××× PCS-68
B26F3: START CONT RLY ON××× SEC-111
B26F4: START CONT RLY OFF××× SEC-112
B26F5: STRG LCK STS SW — ××SEC-113
B26F6: BCM — ××PCS-70
B26F7: BCM ××× SEC-116
B26F8: BCM — ××SEC-117
B26F9: CRANK REQ CIR SHORT — ××SEC-118
B26FA: CRANK REQ CIR OPEN — ××SEC-120
B26FC: KEY REGISTRATION — ××SEC-122
CONSULT display Fail-safe Freeze Frame Data
Vehicle Speed
Odo/Trip Meter
Vehicle Condition Intelligent Key warn-
ing lamp ON Reference
page
Revision: 2010 May2011 QX56

BRC-2
ADDITIONAL SERVICE WHEN REPLACING
ABS ACTUATOR AND ELECTRIC UNIT
(CONTROL UNIT) ..............................................
63
Description ........................................................... ...63
ADJUSTMENT OF STEERING ANGLE SEN-
SOR NEUTRAL POSITION ...............................
64
Description ........................................................... ...64
Work Procedure ......................................................64
CALIBRATION OF DECEL G SENSOR ...........66
Description ........................................................... ...66
Work Procedure ......................................................66
DTC/CIRCUIT DIAGNOSIS ...................... ...68
C1101, C1102, C1103, C1104 WHEEL SEN-
SOR ................................................................. ...
68
DTC Logic ............................................................ ...68
Diagnosis Procedure ..............................................68
C1105, C1106, C1107, C1108 WHEEL SEN-
SOR ....................................................................
70
DTC Logic ............................................................ ...70
Diagnosis Procedure ..............................................70
C1109 POWER AND GROUND SYSTEM .........72
Description ........................................................... ...72
DTC Logic ...............................................................72
Diagnosis Procedure ..............................................72
C1111 PUMP MOTOR .......................................75
DTC Logic ............................................................ ...75
Diagnosis Procedure ..............................................75
C1115 WHEEL SENSOR ...................................77
DTC Logic ............................................................ ...77
Diagnosis Procedure ..............................................77
C1116 STOP LAMP SWITCH ............................79
DTC Logic ............................................................ ...79
Diagnosis Procedure ..............................................79
Component Inspection (Stop lamp Switch) ............85
Component Inspection (Stop Lamp Relay) .............86
C1118 TRANSFER CONTROL UNIT ................87
DTC Logic ............................................................ ...87
Diagnosis Procedure ..............................................87
C1120, C1122, C1124, C1126 ABS IN VALVE
SYSTEM .......................................................... ...
88
DTC Logic ............................................................ ...88
Diagnosis Procedure ..............................................88
C1121, C1123, C1125, C1127 ABS OUT
VALVE SYSTEM ................................................
90
DTC Logic ............................................................ ...90
Diagnosis Procedure ..............................................90
C1130 ENGINE SIGNAL ...................................92
DTC Logic ............................................................ ...92
Diagnosis Procedure ............................................ ...92
C1140 ACTUATOR RELAY SYSTEM ..............93
DTC Logic ............................................................ ...93
Diagnosis Procedure ...............................................93
C1142 PRESS SENSOR ...................................95
DTC Logic ............................................................ ...95
Diagnosis Procedure ...............................................95
C1143 STEERING ANGLE SENSOR ...............97
DTC Logic ............................................................ ...97
Diagnosis Procedure ...............................................97
C1144 INCOMPLETE STEERING ANGLE
SENSOR ADJUSTMENT ..................................
99
DTC Logic ............................................................ ...99
Diagnosis Procedure ...............................................99
C1145, C1146 YAW RATE/SIDE/DECEL G
SENSOR ...........................................................
100
DTC Logic ............................................................ .100
Diagnosis Procedure .............................................100
C1155 BRAKE FLUID LEVEL SWITCH ..........103
DTC Logic ............................................................ .103
Diagnosis Procedure .............................................103
Component Inspection ..........................................104
C1160 DECEL G SEN SET ..............................105
DTC Logic ............................................................ .105
Diagnosis Procedure .............................................105
C1164, C1165 CV SYSTEM .............................106
DTC Logic ............................................................ .106
Diagnosis Procedure .............................................106
C1166, C1167 SV SYSTEM .............................108
DTC Logic ............................................................ .108
Diagnosis Procedure .............................................108
C1170 VARIANT CODING ...............................110
DTC Logic ............................................................ .110
Diagnosis Procedure .............................................110
C118E ACCUMULATOR ..................................111
DTC Logic ............................................................ .111
Diagnosis Procedure .............................................111
U1000 CAN COMM CIRCUIT ...........................112
Description ........................................................... .112
DTC Logic .............................................................112
Diagnosis Procedure .............................................112
POWER SUPPLY AND GROUND CIRCUIT ....113
Description ........................................................... .113
Diagnosis Procedure .............................................113
PARKING BRAKE SWITCH .............................117
Component Function Check ................................ .117
Diagnosis Procedure .............................................117
Component Inspection ..........................................118
Revision: 2010 May2011 QX56

COMPONENT PARTSBRC-13
< SYSTEM DESCRIPTION > [WITH VDC]
C
D
E
G H
I
J
K L
M A
B
BRC
N
O P
Component DescriptionINFOID:0000000006222560
*1: Models with Advanced Driver Assistance System
*2: Models with 4WD system
D. ABS warning lamp, brake warning lamp, VDC warning lamp, VDC OFF
indicator lamp E. Back of spiral cable assembly F. Center console assembly
G. Under center console assembly H. Rear wheel hub and bearing assem- bly
Component Reference/Function
ABS actuator and electric unit
(control unit) Motor/accumulator assembly
BRC-14, "
ABS Actuator and Electric Unit (Control Unit)"
Motor relay
Actuator relay (main relay)
ABS IN valve
ABS OUT valve
Cut valve 1
Cut valve 2
Suction valve 1
Suction valve 2
Control pressure sensor
*1
Accumulator pressure sensor
Master cylinder pressure sensor
Wheel sensor BRC-14, "
Wheel Sensor and Sensor Rotor"
Stop lamp switchBRC-15, "Stop Lamp Switch"
Steering angle sensorBRC-15, "Steering Angle Sensor"
Yaw rate/side/decel G sensorBRC-15, "Yaw Rate/Side/Decel G sensor"
Brake fluid level switch BRC-15, "Brake Fluid Level Switch"
Parking brake switchBRC-15, "Parking Brake Switch"
VDC OFF switchBRC-15, "VDC OFF Switch"
ECMMainly transmits the
following signals to ABS actuator and elec-
tric unit (control unit) via CAN communication.
 Accelerator pedal position signal
 Engine speed signal
Mainly receives the following signals from ABS actuator and
electric unit (control unit) via CAN communication.
 Target throttle position signal
TCM Mainly transmits the
following signals to ABS actuator and elec-
tric unit (control unit) via CAN communication.
 Shift position signal
 Current gear position signal
Transfer control unit
*2Mainly transmits the following signals to ABS actuator and elec-
tric unit (control unit) via CAN communication.
 Current 4WD mode signal
ABS warning lamp
BRC-16, "
System Description"Brake warning lamp
VDC warning lamp
VDC OFF indicator lamp
Revision: 2010 May2011 QX56

BRC-14
< SYSTEM DESCRIPTION >[WITH VDC]
COMPONENT PARTS
ABS Actuator and Electric Unit (Control Unit)
INFOID:0000000006222561
Electric unit (control unit) is in tegrated with actuator and motor/accumulator assembly and comprehensively
controls VDC function, TCS function, AB S function, EBD function, hill start assist function or brake limited slip
differential function.
ELECTRIC UNIT (CONTROL UNIT)
 Brake fluid pressure, engine and transmission are controlled according to signals from each sensor.
 If malfunction is detected, the system enters fail-safe mode.
ACTUATOR
The following components are integrated with ABS actuator.
Motor/accumulator Assembly
Pump Operates the pump drive according to signals from ABS actuator and electric unit (control unit) by the motor.
Motor Operates the motor drive according to signals fr om ABS actuator and electric unit (control unit).
Accumulator
 The accumulator accumulates brake fluid conveyed by the motor and pump.
Motor Relay
Operates the motor ON/OFF according to signals fr om ABS actuator and electric unit (control unit).
Actuator Relay (Main Relay)
Operates each valve ON/OFF according to signals fr om ABS actuator and electric unit (control unit).
ABS IN Valve and ABS OUT Valve
Increases, holds or decreases the fluid pressure of each caliper according to signals from ABS actuator and
electric unit (control unit).
Cut Valve 1, Cut Valve 2
Shuts off the ordinary brake line from master cylinder to signals from ABS actuator and electric unit (control
unit).
Suction Valve 1
Suction Valve 1 switches the brake path to convey accu mulator pressure to the front system, according to a
signal transmitted from the ABS actuat or and electric unit (control unit).
Suction Valve 2
Suction valve 2 releases accumulator pressure, accord ing to a signal transmitted from the ABS actuator and
electric unit (control unit).
Control Pressure Sensor (models with Advanced Driver Assistance System)
Detects the brake fluid pressure of brake caliper side and transmits a signal to ABS actuator and electric unit
(control unit).
Accumulator Pressure Sensor
The accumulator pressure sensor detects brake fluid pressure accumulated in the accumulator and conveys
the detected result to the ABS act uator and electric unit (control unit).
Master cylinder Pressure Sensor
Detects the brake fluid pressure of master cylinder part and transmits a signal to ABS actuator and electric unit
(control unit).
Wheel Sensor and Sensor RotorINFOID:0000000006222562
NOTE:
 Wheel sensor and sensor rotor is integrated in wheel hub assembly.
 Never measure resistance and voltage value using a tester because sensor is active sensor.
Revision: 2010 May2011 QX56

BRC-26
< SYSTEM DESCRIPTION >[WITH VDC]
SYSTEM
ABS FUNCTION
ABS warning lamp and VDC warning lamp in combinati
on meter turn ON when a malfunction occurs in system
[ABS actuator and electric unit (control unit)]. The c ontrol is suspended for VDC function, TCS function, ABS
function, hill start assist function and brake limited sl ip differential (BLSD) function. The vehicle status
becomes the same as models without VDC function, TCS f unction, ABS function, hill start assist function and
brake limited slip differential (BLSD) function. However, EBD function is operated normally.
NOTE:
ABS self-diagnosis sound may be heard the same as in the normal condition, because self-diagnosis is per-
formed when ignition switch turns ON and when vehicle initially starts.
EBD FUNCTION
ABS warning lamp, brake warning lamp and VDC warning lamp in combination meter turn ON when a mal-
function occurs in system [ABS actuator and electric unit (control unit)]. The control is suspended for VDC
function, TCS function, ABS function, EBD function, hill start assist function and brake limited slip differential
(BLSD) function. The vehicle status becomes the sa me as models without VDC function, TCS function, ABS
function, EBD function, hill star t assist function and brake limited slip differential (BLSD) function.
DTC Malfunction detected condition Fail-safe condition
C1101 When an open circuit is detected in rear RH wheel sensor circuit.
The following functions are sus-
pended.
 VDC function
 TCS function
 ABS function
 EBD function (only when both 2 rear wheels are malfunctioning)
 hill start assist function
 Brake limited slip differential
(BLSD) function
C1102 When an open circuit is detected in rear LH wheel sensor circuit.
C1103 When an open circuit is detected in front RH wheel sensor circuit.
C1104 When an open circuit is detected in front LH wheel sensor circuit.
C1105
 When power supply voltage of rear RH wheel sensor is low.
 When distance between rear RH wheel sensor and rear RH wheel sensor rotor is
large.
 When installation of rear RH wheel sensor or rear RH wheel sensor rotor is not
normal.
C1106  When power supply voltage of rear LH wheel sensor is low.
 When distance between rear LH wheel sensor and rear LH wheel sensor rotor is
large.
 When installation of rear LH wheel sensor or rear LH wheel sensor rotor is not nor- mal.
C1107  When power supply voltage of front RH wheel sensor is low.
 When distance between front RH wheel sensor and front RH wheel sensor rotor
is large.
 When installation of front RH wheel sensor or front RH wheel sensor rotor is not normal.
C1108  When power supply voltage of front LH wheel sensor is low.
 When distance between front LH wheel sensor and front LH wheel sensor rotor is
large.
 When installation of front LH wheel sensor or front LH wheel sensor rotor is not normal.
C1109  When ignition voltage is 10 V or less.
 When ignition voltage is 16 V or more. The following functions are sus-
pended.
 VDC function
 TCS function
 ABS function
 EBD function
 hill start assist function
 Brake limited slip differential
(BLSD) function
C 1111
 When a malfunction is detected in motor or motor relay.
 When a low pressure malfunction is detected in accumulator.
 When a malfunction is detected in accumulator pressure sensor.
C 111 5 When difference in wheel speed between any wheel and others is detected during
the vehicle is driven, because of installation of other tires than specified. The following functions are sus-
pended.
 VDC function
 TCS function
 ABS function
 hill start assist function
 Brake limited slip differential
(BLSD) function
C 111 6
 When stop lamp switch signal is not input when brake pedal depress.
 When stop lamp switch signal is not input when stop lamp relay operates.
C 111 8
*1When a malfunction is detected in transfer control unit system.
Revision: 2010 May2011 QX56

SYSTEMBRC-27
< SYSTEM DESCRIPTION > [WITH VDC]
C
D
E
G H
I
J
K L
M A
B
BRC
N
O P
C1120 When a malfunction is detec ted in front LH ABS IN valve.
The following functions are sus-
pended.
 VDC function
 TCS function
 ABS function
 EBD function
 hill start assist function
 Brake limited slip differential (BLSD) function
C1121 When a malfunction is detec
ted in front LH ABS OUT valve.
C1122 When a malfunction is detected in front RH ABS IN valve.
C1123 When a malfunction is det ected in front RH ABS OUT valve.
C1124 When a malfunction is detected in rear LH ABS IN valve.
C1125 When a malfunction is detected in rear LH ABS OUT valve.
C1126 When a malfunction is det ected in rear RH ABS IN valve.
C1127 When a malfunction is detected in rear RH ABS OUT valve.
C1130 When a malfunction is detected in ECM system. The following functions are sus-
pended.
 VDC function
 TCS function
 hill start assist function
 Brake limited slip differential
(BLSD) function
C1140 When a malfunction is detected in actuator relay. The following functions are sus-
pended.
 VDC function
 TCS function
 ABS function
 EBD function
 hill start assist function
 Brake limited slip differential
(BLSD) function
C1142
*2When a malfunction is detected in master cylinder pressure sensor or control pres-
sure sensor. The following functions are sus-
pended.
 VDC function
 TCS function
 hill start assist function
 Brake limited slip differential
(BLSD) function
C1143 When a malfunction is detected in steering angle sensor.
C1144 When neutral position adjustment of steering angle sensor is not complete.
C1145
 When a malfunction is detected in yaw rate signal.
 When yaw rate signal is not continuously received for 2 seconds or more.
 When side G signal is not continuously received for 2 seconds or more.
 When decel G signal is not continuously received for 2 seconds or more.
The following functions are sus-
pended.
 VDC function
 TCS function
 ABS function
 hill start assist function
 Brake limited slip differential
(BLSD) function
C1146 When a malfunction is detected in side/decel G signal.
C1155
 When brake fluid level low signal is detected.
 When an open circuit is detected in brake fluid level switch circuit.
C1160 When calibration of yaw rate/side/decal G sensor is not complete.
C1164 When a malfunction is detected in cut valve 1. The following functions are sus- pended.
 VDC function
 TCS function
 ABS function
 EBD function
 hill start assist function
 Brake limited slip differential (BLSD) function
C1165 When a malfunction is detected in cut valve 2.
C1166 When a malfunction is detected in suction valve 1.
C1167 When a malfunction is detected in suction valve 2.
C1170 When the informatio
n in ABS actuator and electric unit (control unit) is not the same.The following functions are sus-
pended.
 VDC function
 TCS function
 ABS function
 hill start assist function
 Brake limited slip differential
(BLSD) function
DTC Malfunction detected condition Fail-safe condition
Revision: 2010 May2011 QX56