2011 INFINITI QX56 clutch

SYSTEM SYMPTOMTM-171
< SYMPTOM DIAGNOSIS > [7AT: RE7R01B]
C
EF
G H
I
J
K L
M A
B
TM
N
O P
*: Parts behind drum support is impossible to perform inspection by disassembly. Refer to TM-16, "TRANSMISSION : Cross-Sectional
View".Symptom
Diagnostic item
Oil pump
Torque converter
Low brake*
Front brake
High and low reverse clutch
Input clutch
Direct clutch
2346 brake
Reverse brake
1st one-way clutch
2nd one-way clutch
gear
control valve
Parking component
TM-270
TM-211TM-211TM-211TM-292TM-282TM-294TM-270TM-211TM-211TM-287TM-211TM-182TM-211
Func-
tion
trouble
Gear
does no
change“D” posi-
tion Locks in 1GR 1 1 1 2
Locks in 2GR
1
Locks in 3GR 1
Locks in 4GR 1
Locks in 5GR 1
Locks in 6GR 1
Locks in 7GR 1
1GR → 2GR 1 1 1 2
2GR → 3GR 1 2
3GR → 4GR 2111 2
4GR → 5GR 1 1 2
5GR → 6GR 1 2
6GR → 7GR 2111 2
5GR → 4GR 1 2
4GR → 3GR 2 1 2
3GR → 2GR 1 1 2
2GR → 1GR 1 1 1 2
Does not lock-up 1211111 11 2
“M” posi-
tion 1GR
⇔ 2GR 211111 11 2
2GR ⇔ 3GR 211111 11 2
3GR ⇔ 4GR 211111 11 2
4GR ⇔ 5GR 211111 11 2
5GR ⇔ 6GR 211111 11 2
6GR ⇔ 7GR 211111 11 2
Revision: 2010 May2011 QX56

TM-172
< SYMPTOM DIAGNOSIS >[7AT: RE7R01B]
SYSTEM SYMPTOM
SymptomDiagnostic item
Oil pump
Torque converter
Low brake*
Front brake
High and low reverse clutch
Input clutch
Direct clutch
2346 brake
Reverse brake
1st one-way clutch
2nd one-way clutch
gear
control valve
Parking component
TM-270
TM-211TM-211TM-211TM-292TM-282TM-294TM-270TM-211TM-211TM-287TM-211TM-182TM-211
Func-
tion
trouble
Poor
shift-
ingSlip
When
shifting
gears 1GR
⇔ 2GR 1 1 1 2
2GR ⇔ 3GR 1 1 2
3GR ⇔ 4GR 1 2 1 2
4GR ⇔ 5GR 1 1 1 2
5GR ⇔ 6GR 1 1 1 2
6GR ⇔ 7GR 1 1 1 2
En-
gine
brake
does
not
work “D” position
→ “M” position 1 1 1 1 1 2
“M” posi-
tion 7GR
→ 6GR 1 1 1 2
6GR → 5GR 1 1 1 2
5GR → 4GR 1 1 1 2
4GR → 3GR 1 2 1 2
3GR → 2GR 1 1 1 1 1 2
2GR → 1GR 1 1 1 1 2
Revision: 2010 May2011 QX56

SYSTEM SYMPTOMTM-173
< SYMPTOM DIAGNOSIS > [7AT: RE7R01B]
C
EF
G H
I
J
K L
M A
B
TM
N
O P
*: Parts behind drum support is impossible to perform inspection by disassembly. Refer to TM-16, "TRANSMISSION : Cross-Sectional
View".
Func-
tion
trouble
Poor
pow-
er
trans-
mis-
sion
Slip With selector lever
in “D” position, ac-
celeration is ex-
tremely poor.
112 1 12
With selector lever
in “R” position, ac-
celeration is ex-
tremely poor. 11 11112
While starting off
by accelerating in
1GR, engine rac-
es. 112 1112
While accelerating
in 2GR, engine
races. 1 2 1 112
While accelerating
in 3GR, engine
races. 1 2 11 12
While accelerating
in 4GR, engine
races. 1 1 11 12
While accelerating
in 5GR, engine
races. 1 111 12
While accelerating
in 6GR, engine
races. 111112
While accelerating
in 7GR, engine
races. 1 111 2
Lock-up 1 1 1 2
No creep at all. 11211111 11121
Extremely large
creep. 1
Symptom
Diagnostic item
Oil pump
Torque converter
Low brake*
Front brake
High and low reverse clutch
Input clutch
Direct clutch
2346 brake
Reverse brake
1st one-way clutch
2nd one-way clutch
gear
control valve
Parking component
TM-270
TM-211TM-211TM-211TM-292TM-282TM-294TM-270TM-211TM-211TM-287TM-211TM-182TM-211
Revision: 2010 May2011 QX56

TM-174
< SYMPTOM DIAGNOSIS >[7AT: RE7R01B]
SYSTEM SYMPTOM
*: Parts behind drum support is impossible to perform inspection by disassembly. Refer to
TM-16, "TRANSMISSION : Cross-Sectional
View".Symptom
Diagnostic item
Oil pump
Torque converter
Low brake*
Front brake
High and low reverse clutch
Input clutch
Direct clutch
2346 brake
Reverse brake
gear
1st one-way clutch
2nd one-way clutch
control valve
Parking component
TM-270
TM-211TM-211TM-211TM-292TM-282TM-294TM-270TM-211TM-211TM-287TM-211TM-182TM-211
Function
trouble
Power trans-
mission cannot
be performed
Vehicle cannot run in all position. 1 1 2 1 1 1 1 1 1 2 1
Driving is not possible in “D” posi-
tion.
11211111 11121
Driving is not possible in “R” posi-
tion. 1 111121
Engine stall 1
Engine stalls when selector lever
shifted “N” → “D” or “R”. 1
Engine does not start in “N” or “P”
position. 1
Engine starts in position other
than “N” or “P”.
Poor operation Vehicle does not enter parking
condition.
1
Parking condition is not cancelled. 1
Vehicle runs with A/T in “P” posi-
tion. 2111111 21
Vehicle moves forward with the
“R” position. 211111 2
Vehicle runs with A/T in “N” posi-
tion. 2111111 2
Vehicle moves backward with the
“D” position. 12
Revision: 2010 May2011 QX56

TM-186
< REMOVAL AND INSTALLATION >[7AT: RE7R01B]
CONTROL VALVE & TCM
Inspection and Adjustment
INFOID:0000000006226901
INSPECTION AFTER REMOVAL
Check foreign materials in oil pan to help determine causes of mal-
function. If the ATF is very dark, smells burned, or contains foreign
particles, the frictional material (clutches, band) may need replace-
ment. A tacky film that will not wipe clean indicates varnish build up.
Varnish can cause valves, servo, and clutches to stick and can
inhibit pump pressure.
 If frictional material is det ected, perform A/T fluid cooler
cleaning. Refer to TM-97, "
Cleaning".
INSPECTION AFTER INSTALLATION
Check A/T fluid leakage. Refer to TM-175, "Inspection".
ADJUSTMENT AFTER INSTALLATION
 Adjust A/T fluid level. Refer to TM-95, "Adjustment".
 Perform decel G sensor calibration when replacing control valve & TCM. Refer to TM-92, "
Special Repair
Requirement".
SCIA5199E
Revision: 2010 May2011 QX56

TM-198
< REMOVAL AND INSTALLATION >[7AT: RE7R01B]
OUTPUT SPEED SENSOR
- Tighten rear extension assembly bolts to the specified torque.
 Refer to the followings when installing oil pan (2) (with oil pan gas-
ket) and clips (1) to transmission case.
CAUTION:
 Never reuse oil pan gasket and oil pan mounting bolts.
 Install oil pan gasket in the di rection to align hole position.
 Install it so that drain plug comes to the position as shown
in the figure.
 Be careful not to pinch harnesses.
 Completely remove all moisture, oil and ol d gasket, etc. from oil pan mounting surface.
- Tighten oil pan mounting bolts to the specified torque in numerical
order shown in the figure after temporarily tightening them. Tighten
necessary oil pan mounting bolts with specified torque.
2WD : Inspection and AdjustmentINFOID:0000000006228121
INSPECTION AFTER REMOVAL
Check foreign materials in oil pan to help determine causes of mal-
function. If the ATF is very dark, smells burned, or contains foreign
particles, the frictional material (clutches, band) may need replace-
ment. A tacky film that will not wipe clean indicates varnish build up.
Varnish can cause valves, servo, and clutches to stick and can
inhibit pump pressure.
If frictional material is det ected, perform A/T fluid cooler
cleaning. Refer to TM-97, "
Cleaning".
INSPECTION AFTER INSTALLATION
Check A/T fluid leakage Refer to TM-175, "Inspection".
1: Bracket
A: Bolt
B : Self-sealing bolt
JSDIA1845ZZ
: Vehicle front
: Oil pan mounting bolt
: Vehicle front
JSDIA1591ZZ
JSDIA1592GB
SCIA5199E
Revision: 2010 May2011 QX56

TM-212
< UNIT DISASSEMBLY AND ASSEMBLY >[7AT: RE7R01B]
TRANSMISSION ASSEMBLY
1. Torque converter 2. Converter housing 3. Oil pump housing oil seal
4. Oil pump housing 5. O-ring 6. Oil pump cover
7. O-ring 8. D-ring 9. D-ring
10. Front brake piston 11. Front brake spring retainer 12. Snap ring
13. D-ring 14. D-ring 15. 2346 brake piston
16. 2346 brake spring retainer 17. Snap ring 18. Seal ring
19. 2346 brake dish plate 20. 2346 brake driven plate 21. 2346 brake drive plate
22. 2346 brake retaining plate 23. Snap ring 24. Bearing race
25. Needle bearing 26. Under drive sun gear 27. Needle bearing
28. Front brake retaining plate 29. Front brake drive plate 30. Front brake driven plate
31. Front brake retaining plate 32. Snap ring 33. 1st one-way clutch
34. Snap ring 35. Under drive carrier assembly 36. Front brake hub assembly
: Apply Genuine RTV silicone sealant or equivalent. Refer to GI-22, "
Recommended Chemical Products and Sealants".
Refer to GI-4, "
Components" for symbols not described on the above.
JPDIA1141ZZ
Revision: 2010 May2011 QX56

TRANSMISSION ASSEMBLYTM-213
< UNIT DISASSEMBLY AND ASSEMBLY > [7AT: RE7R01B]
C
EF
G H
I
J
K L
M A
B
TM
N
O P
1. Needle bearing 2. Snap ring 3. Front carrier assembly
4. Needle bearing 5. O-ring 6. Seal ring
7. Input clutch assembly 8. Rear internal gear 9. Needle bearing
10. Mid carrier assembly 11. Needle bearing 12. Bearing race
13. Rear carrier assembly 14. Needle bearing 15. Mid sun gear
16. Seal ring 17. Rear sun gear 18. 2nd one-way clutch
19. Snap ring 20. Needle bearing 21. High and low reverse clutch hub
22. Snap ring 23. Bearing race 24. Bearing race
25. Needle bearing
Refer to GI-4, "
Components" for symbols not described on the above.
Revision: 2010 May2011 QX56