2011 INFINITI QX56 Eco

PARKING COMPONENTSTM-187
< REMOVAL AND INSTALLATION > [7AT: RE7R01B]
C
EF
G H
I
J
K L
M A
B
TM
N
O P
PARKING COMPONENTS
2WD
2WD : Exploded ViewINFOID:0000000006233258
2WD : Removal and InstallationINFOID:0000000006233259
REMOVAL
1. Drain ATF through drain plug.
2. Separate propeller shaft assembly. Refer to DLN-143, "
Exploded View".
3. Support A/T assembly with a transmission jack. CAUTION:
When setting transmission jack, be careful not to allow it to collide against the drain plug.
4. Remove rear engine mounting cross member with power tool. Refer to TM-205, "
2WD : Exploded View".
5. Remove engine mounting insulator (rear). Refer to TM-205, "
2WD : Exploded View".
1. Parking actuator support 2. Parking pawl 3. Return spring
4. Pawl shaft 5. Parking gear 6. Seal ring
7. Output shaft 8. Bearing race 9. Needle bearing
10. Self-sealing bolt 11. Bracket 12. Rear extension
*: Apply Genuine Anaerobic Liquid Gasket or equivalent. Refer to GI-22, "Recommended Chemical Products and Sealants".
Refer to GI-4, "
Components" for symbols not described on the above.
JSDIA1926GB
Revision: 2010 May2011 QX56

TM-190
< REMOVAL AND INSTALLATION >[7AT: RE7R01B]
PARKING COMPONENTS
16. Remove return spring (1) from parking pawl (2).
INSTALLATION
Note the following, and install in the reverse order of removal.
CAUTION:
 Never reuse seal rings and drain plug gasket.
 Apply petroleum jelly to n
eedle bearing and seal rings.
 Insert the tip of parking rod between the parki ng pawl and the parking actuator support when assem-
bling the rear extension assembly.
 Refer to the followings installing rear extension assembly.
- Apply recommended sealant (Genuine Anaerobic Liquid Gasket or
equivalent. Refer to GI-22, "
Recommended Chemical Products
and Sealants".) to rear extension assembly as shown in the figure.
CAUTION:
Completely remove all moisture, oil and old sealant, etc. from
the transmission case and rear extension assembly mounting
surfaces.
- Tighten rear extension assembly bolts to the specified torque.
2WD : InspectionINFOID:0000000006233260
INSPECTION AFTER REMOVAL
SCIA6180J
Sealant starting
point and end-
point (A) : Start and finish
point shall be in
the center of two bolts.
Overlap width of
sealant starting
point and end-
point (B) : 3 – 5 mm (0.12 – 0.20 in)
Sealant width (C) : 1.0 – 2.0 mm (0.04 – 0.08 in)
Sealant height (C) : 0.4 – 1.0 mm (0.016 – 0.04 in)
JSDIA1855ZZ
1: Bracket
A: Bolt
B : Self-sealing bolt
JSDIA1845ZZ
Revision: 2010 May2011 QX56

OUTPUT SPEED SENSORTM-195
< REMOVAL AND INSTALLATION > [7AT: RE7R01B]
C
EF
G H
I
J
K L
M A
B
TM
N
O P
OUTPUT SPEED SENSOR
2WD
2WD : Exploded ViewINFOID:0000000006228119
2WD : Removal and InstallationINFOID:0000000006228120
REMOVAL
1. Disconnect the battery cabl e from the negative terminal.
2. Drain ATF through drain plug.
3. Separate propeller shaft assembly. Refer to DLN-143, "
Exploded View".
1. A/T 2. Oil pan gasket 3. Oil pan
4. Clip 5. Oil pan mounting bolt 6. Overflow plug
7. Drain plug 8. Drain plug gasket 9. Magnet
10. Output speed sensor 11. Self-sealing bolt 12. Bracket
13. Rear extension
*: Apply Genuine Anaerobic Liquid Gasket or equivalent. Refer to GI-22, "Recommended Chemical Products and Sealants".
Refer to GI-4, "
Components" for symbols not described on the above.
JSDIA1925GB
Revision: 2010 May2011 QX56

OUTPUT SPEED SENSORTM-197
< REMOVAL AND INSTALLATION > [7AT: RE7R01B]
C
EF
G H
I
J
K L
M A
B
TM
N
O P
12. Disconnect output speed sensor connector (A). CAUTION:
Be careful not to damage connector
13. Disengage terminal clips ( ).
14. Remove output speed sensor (1) from transmission case.
CAUTION:
 Never subject it to impact by dropping or hitting it.
 Never disassemble.
 Never allow metal filings, etc. to get on the sensor's frontedge magnetic area.
 Never place in an area affected by magnetism.
INSTALLATION
Note the following, and install in the reverse order removal.
CAUTION:
 Insert the tip of parking rod between the parkin g pole and the parking actuator support when assem-
bling the rear ext ension assembly.
 Never reuse drain plug gasket.
 Refer to the followings when installing output speed sensor.
CAUTION:
 Never subject it to impact by dropping or hitting it.
 Never disassemble.
 Never allow metal filings, etc. to get on the sensor's front edge magnetic area.
 Never place in an area affected by magnetism.
 Refer to the followings when installing rear extension assembly.
- Apply recommended sealant (Genuine Anaerobic Liquid Gasket or equivalent. Refer to GI-22, "
Recommended Chemical Products
and Sealants".) to rear extension assembly as shown in the figure.
CAUTION:
Completely remove all moisture, oil and old sealant, etc. from
transmission case and rear extension assembly mounting
surfaces.
JPDIA1104ZZ
: Bolt
JSDIA1885ZZ
Sealant starting
point and end-
point (A) : Start and finish point shall be in
the center of two bolts.
Overlap width of
sealant starting
point and end-
point (B) : 3 – 5 mm (0.12 – 0.20 in)
Sealant width (C) : 1.0 – 2.0 mm (0.04 – 0.08 in)
Sealant height (C) : 0.4 – 1.0 mm (0.016 – 0.04 in)
JSDIA1855ZZ
Revision: 2010 May2011 QX56

TM-212
< UNIT DISASSEMBLY AND ASSEMBLY >[7AT: RE7R01B]
TRANSMISSION ASSEMBLY
1. Torque converter 2. Converter housing 3. Oil pump housing oil seal
4. Oil pump housing 5. O-ring 6. Oil pump cover
7. O-ring 8. D-ring 9. D-ring
10. Front brake piston 11. Front brake spring retainer 12. Snap ring
13. D-ring 14. D-ring 15. 2346 brake piston
16. 2346 brake spring retainer 17. Snap ring 18. Seal ring
19. 2346 brake dish plate 20. 2346 brake driven plate 21. 2346 brake drive plate
22. 2346 brake retaining plate 23. Snap ring 24. Bearing race
25. Needle bearing 26. Under drive sun gear 27. Needle bearing
28. Front brake retaining plate 29. Front brake drive plate 30. Front brake driven plate
31. Front brake retaining plate 32. Snap ring 33. 1st one-way clutch
34. Snap ring 35. Under drive carrier assembly 36. Front brake hub assembly
: Apply Genuine RTV silicone sealant or equivalent. Refer to GI-22, "
Recommended Chemical Products and Sealants".
Refer to GI-4, "
Components" for symbols not described on the above.
JPDIA1141ZZ
Revision: 2010 May2011 QX56

TM-216
< UNIT DISASSEMBLY AND ASSEMBLY >[7AT: RE7R01B]
TRANSMISSION ASSEMBLY
4WD MODELS
13. Snap ring 14. Oil pan gasket 15. Oil pan
16. Clip 17. Oil pan mounting bolt 18. Overflow plug
19. Drain plug 20. Drain plug gasket 21. Magnet
22. Clip 23. Control valve & TCM 24. Joint connector
25. Transmission case 26. Retaining pin 27. Output speed sensor
28. Needle bearing 29. Parking gear 30. Seal ring
31. Output shaft 32. Bearing race
Refer to
GI-4, "
Components" for symbols in the figure.
1. Parking actuator support 2. Parking pawl 3. Pawl shaft
4. Return spring 5. Needle bearing 6. Rear extension
7. Self-sealing bolt 8. Rear oil seal 9. Bracket *: Apply Genuine Anaerobic Liquid Gasket or equivalent. Refer to GI-22, "
Recommended Chemical Products and Sealants".
Refer to GI-4, "
Components" for symbols in the figure.
JSDIA1841GB
Revision: 2010 May2011 QX56

TM-218
< UNIT DISASSEMBLY AND ASSEMBLY >[7AT: RE7R01B]
TRANSMISSION ASSEMBLY
19. 2346 brake dish plate 20. 2346 brake driven plate 21. 2346 brake drive plate
22. 2346 brake retaining plate 23. Snap ring 24. Bearing race
25. Needle bearing 26. Under drive sun gear 27. Needle bearing
28. Front brake retaining plate 29. Front brake drive plate 30. Front brake driven plate
31. Front brake retaining plate 32. Snap ring 33. 1st one-way clutch
34. Snap ring 35. Under drive carrier assembly 36. Front brake hub assembly
: Apply Genuine RTV silicone sealant or equivalent. Refer to GI-22, "
Recommended Chemical Products and Sealants".
Refer to GI-4, "
Components" for symbols not described on the above.
1. Needle bearing 2. Snap ring 3. Front carrier assembly
4. Needle bearing 5. O-ring 6. Seal ring
7. Input clutch assembly 8. Rear internal gear 9. Needle bearing
10. Mid carrier assembly 11. Needle bearing 12. Bearing race
13. Rear carrier assembly 14. Needle bearing 15. Mid sun gear
16. Seal ring 17. Rear sun gear 18. 2nd one-way clutch
19. Snap ring 20. Needle bearing 21. High and low reverse clutch hub
JPDIA1141ZZ
Revision: 2010 May2011 QX56

TM-240
< UNIT DISASSEMBLY AND ASSEMBLY >[7AT: RE7R01B]
TRANSMISSION ASSEMBLY
52. Remove needle bearing from drum support edge surface.
53. Remove reverse brake piston (1) from transmission case with
compressed air. Refer to TM-222, "
Oil Channel".
CAUTION:
Care should be taken not to ab ruptly blow air. It makes pis-
tons incline, as the result, it becomes hard to disassemble
the pistons.
54. Remove D-rings from reverse brake piston.
55. Remove manual shaft retaining pin with pair of nippers. CAUTION:
Be careful not to cut retaining pin.
SCIA2796E
A : Reverse brake pressure hole
JSDIA1819ZZ
SCIA6330E
SCIA2329E
Revision: 2010 May2011 QX56