Page 32 of 164
i
i
i
Monitoring
30
This function gives an estimate of the number
of miles (km) that your vehicle can still cover,
based on the recent conditions of use (driving
style, use of heating, air conditioning...).
Range indicator
When the remaining range falls to a low level,
"- - -"
is displayed in the instrument panel.
The display of "---"
, indicating that
the ser vice date has arrived, comes on
automatically after a cer tain time and
distance travelled. The screen then
indicates the time remaining before
the next ser vice is due.
Resetting the service indicator to zero
After each ser vice, the ser vice indicator should
be rest to zero.
The procedures is as follows:
)
Switch off the ignition (switch in the LOCK
or ACC position).
)
Press the reset button A
several times in
succession until the ser vice indicator is
displayed.
)
Press and hold the reset button for a few
seconds until the spanner flashes
.
)
Press the reset button while the spanner is
flashing to change the display from "---"
to
"CLEAR"
.
The distance (or time) remaining before
the next ser vice is due is displayed. The range can be displayed in miles or
kilometres.
To change the units, refer to the
"Distance recorder" section.
Page 34 of 164
Access
32
Folding the key
Anti-theft protection
)
First press button A
to fold the key.
Electronic engine immobiliser
The key contains an electronic chip which has a
special code. When the ignition is switched on,
this code must be recognised to permit star ting.
This electronic engine immobiliser locks the
engine management system a few moments
after the ignition is switched off and prevents
star ting of the engine by anyone who does not
have the key.
In the event of a malfunction and if your vehicle
does not start, contact a CITROËN dealer as
soon as possible.
Remote control problem
In the event of a remote control malfunction,
you can neither unlock nor lock your vehicle.
)
First of all, use the key in the driver's door
lock to unlock or lock your vehicle.
)
Then, contact a CITROËN dealer to check
the operation of the remote control and
replace the battery if necessary.
Page 35 of 164
2
!
Access
33
Lost keys
Visit a CITROËN dealer with the vehicle's V5 registration document and your personal
identification documents.
The CITROËN dealer will be able to retrieve the key code and the transponder code
required to order a replacement key.
Remote control
The high frequency remote control is a sensitive system; do not operate it while it is in your
pocket as there is a possibility that it may unlock the vehicle, without you being aware of it.
Do not repeatedly press the buttons of your remote control out of range and out of sight of
your vehicle. You run the risk of stopping it from working.
The remote control does not operate when the key is in the ignition, even when the ignition
is switched off.
Locking the vehicle
Driving with the doors locked may make access to the passenger compar tment by
the emergency services more difficult in an emergency.
As a safety precaution (with children on board), remove the key from the ignition when you
leave the vehicle, even for a shor t time.
Anti-theft protection
Do not make any modifications to the electronic immobiliser system; this could cause
malfunctions.
When purchasing a second-hand vehicle
Have the key codes memorised by a CITROËN dealer, to ensure that the keys in your
possession are the only ones which can star t the vehicle.
Page 36 of 164
i
!
Access
34
1.
Driver's electric window switch.
2.
Passenger's electric window switch.
3.
Rear right electric window switch.
4.
Rear left electric window switch.
5.
Deactivating the passenger and rear
electric window switches.
Electric windows
Operation
Deactivating the passenger and
rear electric window switches
)
For the safety of your children, press switch 5
to prevent operation of the passenger and rear
electric windows irrespective of their position.
When the button is pressed down, the switches
are deactivated.
When the button is raised, the switches are activated.
System which opens or closes a window manually or automatically. It is fitted with a deactivation system to prevent misuse of the rear controls.
The electric window switches
remain operational for approximately
30 seconds after the ignition is
switched off.
The windows can no longer be opened
or closed after the driver's door is
closed. With the ignition on:
)
Press the switch gently to open or pull it
gently to close. The window stops as soon
as the switch is released.
- Automatic one-touch mode
(driver's side)
)
Press the switch fully to open. The
driver's window opens completely when
the switch is released.
)
Pressing the switch again stops the
movement of the window.
Always remove the key from the ignition when leaving the vehicle, even for a
shor t time.
In the event of contact during operation
of the windows, you must reverse the
movement of the window. To do this,
press the switch concerned.
When the driver operates the passenger electric window switches, they must
ensure that no one is preventing correct
closing of the windows.
The driver must ensure that passengers
use the electric windows correctly.
Be aware of children when operating
the windows.
Page 44 of 164
!
Comfort
42
Door mirrors
The mirrors can be adjusted when the ignition
switch is in the "ON" or "ACC" position.
)
Move control A
to the right or to the left to
select the corresponding mirror.
)
Direct control B
in all four directions to
adjust the mirror.
When adjustment is complete, return control A
to the central position.
Adjustment
The mirrors can also be folded
manually.
However, you must never unfold them
manually
, other wise the mirrors may
not remain in place correctly when
driving.
Always use control C
to unfold them.
)
With the ignition switch in the "ON" or
"ACC" position: press control C
to unfold
them
)
With the ignition switch in the "LOCK"
position: press control C within
30 seconds
to fold them.
Electric folding/unfolding
Page 54 of 164
i
!
Driving
52
Starting - stopping the vehicle
- Position 1: LOCK
The steering is locked.
- Position 2: ACC
The ancillaries (radio, 12 V socket...) can
be used.
- Position 3: ON
Ignition on.
- Position 4: START
"Ready" lamp on.
Motor ready to drive the vehicle.
Ignition switch
)
Inser t the key in the ignition switch.
)
Turn the key to position 4 (START)
.
Starting
Stopping
)
Immobilise the vehicle.
)
Place the drive selector in position P
.
)
Turn the key to position 1 (LOCK)
.
)
Remove the key from the ignition switch.
)
Hold it in this position for a few
seconds until the " READY"
lamp
comes on accompanied by an
audible signal.
)
Release the key.
The key returns automatically to
position 3 (ON)
.
Do not attach any heavy objects to the
key as this could weigh down on it when
in the ignition switch and cause a fault.
If you use the ancillaries for a prolonged
period (with the key in the ACC
position),
you risk discharging the ancillaries
battery. Starting your vehicle will then no
longer be possible. Be aware
.
Page 55 of 164
4
!
Driving
53
Manual parking brake
Applying
)
Pull the parking brake lever fully up to
immobilise your vehicle.
When parking on a slope, direct your
wheels against the kerb, apply the
parking brake, place the drive selector
in position P
and switch off the ignition.
Releasing
)
Pull the parking brake lever up gently,
press the release button then lower
the lever fully.
When the vehicle is being driven,
if the parking brake is still on or has
not been fully released, this warning
lamp comes on.
Page 57 of 164
4
!
Driving
55
To tow your vehicle, the drive selector
must be in position N
, refer to "Practical
Information".
Parking the vehicle
To stop the motor, you must select position P
.
You must apply the parking brake to immobilise
the vehicle.
To remove the key from the ignition switch, the
drive selector must be in position P
.
