Page 17 of 164
.Familiarisation
15
Driving safely
P.
Parking.
Press the brake pedal to come out of
this position.
R.
Reverse.
N.
Neutral.
D.
Drive (for ward).
Drive selector
54
- Check that the drive selector is in position P
.
- Inser t the key in the ignition switch.
- Turn the key to position 4 (START)
.
- Hold it in this position for a few seconds,
until the " READY
" lamp comes on,
accompanied by an audible signal.
- Release the key.
The switch returns automatically to
position 3 (ON)
.
Starting the motor
52
- Stop the vehicle.
- Keep your foot on the brake pedal.
- Put the drive selector in position P
.
- Apply the parking brake.
- Turn the key anti-clockwise to the LOCK
position.
Stopping the motor
52
Page 22 of 164

Monitoring
20
Operation indicator lamps
If one of the following indicator lamps comes on in the instrument panel, this confirms that the corresponding system has come into operation.
Warning/indicator lamp
State
Cause
Action/Observations
Left-hand
direction indicato
r
Flashing with audible
signal. The lighting stalk is pushed down.
Right-hand
direction indicator
Flashing with audible
signal. The lighting stalk is pushed up.
Hazard warning
lamps
Flashing with audible
signal. The hazard warning lamps switch,
located on the dashboard, has been
operated. The left-hand and right-hand direction indicators and
their associated indicator lamps flash simultaneously.
Sidelamps
and/
or dipped beam
headlamps
On fixed. The sidelamps and/or dipped beam
headlamps are on.
Front foglamps
On fixed. The front foglamps are switched on. Turn the ring on the stalk rear wards twice to switch off
the front foglamps.
Rear foglamp
On fixed. The rear foglamp is switched on. Turn the ring on the stalk rear wards to switch off the
rear foglamp.
Main beam
headlamps
On fixed. The lighting stalk is pulled towards
you. Pull the stalk to return to dipped beam headlamps.
Page 54 of 164

i
!
Driving
52
Starting - stopping the vehicle
- Position 1: LOCK
The steering is locked.
- Position 2: ACC
The ancillaries (radio, 12 V socket...) can
be used.
- Position 3: ON
Ignition on.
- Position 4: START
"Ready" lamp on.
Motor ready to drive the vehicle.
Ignition switch
)
Inser t the key in the ignition switch.
)
Turn the key to position 4 (START)
.
Starting
Stopping
)
Immobilise the vehicle.
)
Place the drive selector in position P
.
)
Turn the key to position 1 (LOCK)
.
)
Remove the key from the ignition switch.
)
Hold it in this position for a few
seconds until the " READY"
lamp
comes on accompanied by an
audible signal.
)
Release the key.
The key returns automatically to
position 3 (ON)
.
Do not attach any heavy objects to the
key as this could weigh down on it when
in the ignition switch and cause a fault.
If you use the ancillaries for a prolonged
period (with the key in the ACC
position),
you risk discharging the ancillaries
battery. Starting your vehicle will then no
longer be possible. Be aware
.
Page 59 of 164

5
i !
Visibility
57
Front and rear foglamps
Foglamps selection ring.
The foglamps operate with the sidelamps and
dipped and main beam headlamps.
Front and rear foglamps.
In good or rainy weather, both day
and night, the front foglamps and
the rear foglamp is prohibited. In these
situations, the power of its beam may
dazzle other drivers.
Do not forget to switch off the front
foglamps and the rear foglamp when
they are no longer necessary.
Lighting on reminder
There is an audible signal when the
driver's door is opened, to warn the
driver if the vehicle lighting is on, with
the ignition off.
Switching off the lighting stops
the audible signal.
)
To switch on the front foglamps, turn the
ring for wards once.
)
To switch on the rear foglamp, turn the ring
forwards twice.
)
To switch off the rear foglamp, turn the ring
rear wards twice.
)
To switch off the front foglamps, turn the
ring rear wards once.
The ring returns to its initial position
automatically.
The rear foglamp is switched off automatically
when you switch off the sidelamps, or
the dipped or main beam headlamps.
Page 75 of 164