2011 AUDI TT ROADSTER warning

192 Checking and filling
Charging of battery
Starting the engine requires a well charged battery.
,. Always read and heed all W ARNIN GS be­
low
c> A and c> A in Working on the bat­
tery on page 190.
,. Switch off the ignitio n and all electrical con­
s u mers.
,. Make sure the area is well vent ilated when
yo u charge the battery.
,. Connect charger cables.
ALWAY S co nnect
ch arg er ca ble s PO SITIV E
G) to POSITIVE
G) ; NE GATI VE Q to NEGATI VE Q .
,. Switch on the charger.
,. Make sure the charging rate is not over
6 amps.
,. Turn off the charger¢.&_.
,. Disconnect the charger cables .
,. Connect both battery cables to the battery if
necessary-
first plus, then m inus.
It is not necessary to remove the battery from
the luggage compartment, and it is also not
necessa ry to disconnect the cables.
Normally, a battery should be charged at no
more than 10 percent of its rated capacity.
For example, a charging current of 4.5 amps
wou ld be used on a battery rated at 45 Ah.
Rated capacity of the battery in your veh icle is
listed on the battery housing .
The battery caps should
not be opened when
charging a battery.
&,. WARNING
-
Charging a battery can be dangerous.
- Never charge a frozen battery . It may ex­
plode because of gas trapped in the ice.
Allow a frozen battery to thaw out first.
- Do not reuse batteries which were fro­
zen. The battery housing may have
c racked and weakened whe n the battery
froze.
- Charge the battery in a we ll ventilated
area . Keep away from open f lame o r elec­
t ric al spa rk . Do not smoke. Hydrogen gas
gene rate d by the b attery is exp losive. -
To reduce the danger of explosion, never
connect or d isconnect charger cab les
while the charger is operating .
- Fast charging a battery is dangerous and
should only be attempted by a compe­
tent tech nician with the proper equip­
ment .
- Battery acid that may spill during charg­
ing should be washed off with a solution
of wa rm water and bak ing soda to neu­
tralize th e ac id .
(D Note
Never use a fast charger as a booster to
start the eng ine . Th is w ill seriously dam­
age sensit ive electronic components, such
as cont ro l units, re lays, radio, etc., as well
as the battery charger.
{1) Tips
The vehicle batte ry must not be charged
with a standa rd small charger that p lugs
i nto the cigarette lig hter or outlet.
Windshield/head Light
washer container
Fig . 14 5 Fender, left: Windshie ld washer fluid reser·
vo ir
T he washer fluid container is marked with the
symbol
O on its cap.
,. Before you check any thing in the engine
compa rtme nt,
a lwa ys read and heed all
WARNINGS ¢
A in Working in the engine
compartment on page 178 .
,. Lift the filler cap tongue to add washer flu-
id. You can fill the container to the top.
111>

194 Tire s and wheel s
Tires and wheels
Tires
General notes
Tires may be the least appreciated and most
abused parts of a motor vehicle .
Tires may be the least appreciated and most
abused parts of a motor vehicle . Tires are,
however, one of the most important parts of a
vehicle, particularly considering the compara ­
tive ly small patch of rubber on each tire that
assures that a ll-important contact between
you, you r vehicle and the road.
Maintaining the correct tire pressure, mak ing
sure that your veh icle and its t ires do not have
to carry mo re weight than they can safe ly han­
d le, avoiding damage from roa d haza rds and
r eg ularly inspecting t ires for damage includ­
ing cuts, slashes irregu la r wear and ove rall
condition are the most important things that
you can do to he lp avoid s udden tire failure in­
cluding tread separat ion and blowouts.
Avoiding damage
If you have to drive over a curb or similar ob­
stacle, drive very s low ly and as close as possi ­
b le at a right angle to the curb.
A lways keep chem ica ls incl ud ing gre ase, o il,
gasoline and b rake fluid off the t ires .
Inspect the t ir e s regularly for damage (cuts,
cracks or b listers, etc.). Remove any fo reign
bod ies embedded in the treads.
Storing tires
Mark ti res when you remove them to indicate
the direction of rotation . T his ensures you to
be ab le to mount them correctly when you re­
install t hem.
When removed, the whee ls or t ires should be
stored in a cool, d ry and preferably dark place .
Store tires in a vertical pos ition if they are not
mounted on rims, in a horizontal pos it ion if
they are mounted on rims.
New tires
New t ires have to be broken in¢&,. .
T he tread depth of new t ires may vary, accord­
ing to the type a nd make of t ire and the tread
pa tte rn .
Hidden damage
Damage to tires and r ims is ofte n not readily
vis ible . If you notice unusual v ibrat ion or the
vehicle p ulls to one side, th is may ind icate
t h at one of the t ires has been damaged . Th e
t ir es m ust be checked immed iate ly by an au ­
tho rized Aud i dea le r or q uali fied wor ks hop.
Unidirectional t ires
A un idirectional tire can be identified by ar­
rows on the sid ewa ll, that po int in the direc­
t ion the t ire is desig ned to rotate. You must
f ol low the specified d irec tion of rot ation . This
is necessa ry so tha t these tires can develop
their optimum characterist ics regarding grip,
road no ise, wear and hyd rop laning resistance.
For more information ¢
page 226.
A WARNING
-New tires or t ires that are o ld, worn or
damaged cannot provide maximum con­
trol and braking ability .
-
-New tires tend to be slippery and must
be broken in . To reduce the risk of losing
control, a co llision and ser ious personal
in jur ies, d rive w ith special ca re fo r the
fi rst 3 50 m iles (560 km).
- Driving with worn or damaged tires can
le ad to loss of control, sudden tire fail­
ure, including a blowou t and sudden de­
fla tion, crashes and seriou s personal in­
juries . Have wo rn or damaged t ires re­
p laced immediate ly .
- Ti res age even if they are not being used
an d can fai l sudden ly, especially at high
speeds. Tires that are more than 6 years
old can only be used in an emergency
and then w ith specia l care and at low
speed.

196 Tires and wheels
Maximum loaded vehicle weight
means the sum of:
(a) Curb weight
(b) Accessory weight
(c) Vehicle capacity we ight, and
(d) Production options weight
Maximum (permissible) inflation pressure
means the maximum cold inflation pressu re
to which a tire may be inflated. Also called
"maximum inflation p ressure."
Normal occupant weight
means 150 lbs. (68 kilograms) times the
number of occupants seated in the vehicle up
to the total seating capacity of your vehicle.
Occupant distribution means distribution of occupants in a vehicle .
Outer diameter means the overa ll diameter of an inf lated new
tire.
Overall width
means the linear distance between the exteri­
ors of the sidewalls of an inflated tire, includ­
ing e levations due to labeling, decorations, or
protective bands or ribs.
Ply
means a laye r of rubber-coated parallel cords.
Production options weight
means the comb ined we ight of those installed
regular production options weighing over 5
lbs . (2 .3 kg) in excess of those standard items
which they replace, not previously considered
in curb weight or accessory weight, including
heavy duty brakes, r ide leve lers, heavy duty
battery, and special trim.
Radial ply tire
means a pneumatic tir e in which the p ly cords
that extend to the beads are laid at substan­
tially 90 degrees to the centerline of the
tread . Recommended inflation pressure
see
~
page 195, Cold tire inflation pressure.
Reinforced tire
means a t ire designed to operate at higher
loads and at higher inflation p ressures than
the corresponding standard tire. Reinforced
ti res my be ident ified as "XL" "xl" "E XTRA
, ,
LOAD", or "RF" on the sidewall.
Rim
means a metal support for a tire or a t ire and
tube assembly upon which the tire beads are seated.
Rim diameter
means nominal d iameter of the bead seat. If
you change your wheel s ize, you w ill have to
purchase new tires to match the new r im di­
ameter .
Rim size designation
means rim diameter and width.
Rim width
means nominal distance between rim flanges .
Sidewall
means that portion of a tire between the
tread and bead.
Speed rating (letter code)
means the speed at which a tire is designed to
be driven for extended periods of time. The
r atings range from 93 mph (150 km/h) to
186 mph (298 km/h)
~ page 206 . You may
not find this information on all tires because
it is not requ ired by law.
T he speed rating letter code, where applica­
ble, is molded on the tire sidewall and indi­
cates the maximum perm iss ibl e road speeds
~ A in Winter tires on page 209 .
Tire pressure monitoring system
means a system that detects when one or
more of a veh icle's tires are underinflated and
i lluminates a low tire pressure warning tell-
tale. ..,_

200 Tires and wheels
other cargo that the vehicle can carry. For the
location of the tire pressure label
r=:>fig. 146.
A WARNING
Overloading a vehicle can cause loss of ve­
hicle control, a crash or other accident, se­
rious personal injury, and even death.
- Carrying more weight than your vehicle
was designed to carry will prevent the
vehicle from handling properly and in­
crease the risk of a loss of veh icle con­
trol.
- The brakes on a vehicle that has been
overloaded may not be able to stop the
vehicle within a safe distance.
- Tires on a vehicle that has been overload­
ed can fail suddenly causing loss of con­
tro l and a crash.
A WARNING ,~ -
- Incorrect tire pressures and/or underin­
flation can lead to a serious or fatal acci­
dent.
- Incorrect tire pressures and/or underin­
flation cause increased tire wear and can
affect the handling of the vehicle.
- Incorrect tire pressures and/or underin­
flation can also lead to sudden tire fa il­
ure, including a blowout and sudden de­
flation, causing loss of vehicle control.
Checking tire pressure
The correct tire pressure for the tires original­
ly installed on your vehicle is listed on the tire
pressure label located on driver's side 8-pil ­
lar.
The recommended t ire pressures are on the
tire pressure labe l and in the table
r=:> page 198, Cold tire inflation pressure . This
means that the pressure must be checked and
adjusted when the tire has not been driven for more than a couple of miles (kilometers) at
low speeds during the previous three hours.
A ir i n the tires expands when the tire heats up
as a result of interna l fr iction as it flexes in use.
The tire pressure is higher when the tire
has warmed up than when it is "co ld."
It i s the inflation pressure in a "cold" tir e that
counts. Therefore, you should never let air out
of a warm tire to match "Cold tire inflation
pressure" recommendations
r=;, page 198. The
t ir es wou ld then be underinf lated and co uld
fail suddenly .
The tire pressure label on your Audi lists the
recommended cold tire inflation pressures for
the new, original eq uipment tires that were
on your veh icle at the time it was manufac­
tured. For the location of the labe l
r=:>page 198, fig . 146.
Most tires lose air natura lly over t ime. They
can a lso lose some air if you drive over a pot­
hole or hit a curb while park ing. It is usually
not possible to see whether the rad ial tires
used today are underinflated just by looking
at them.
Therefore, be sure to check t ire pressures at
least once a month and a lways before going
on a long trip . Make sure to take the number
of peop le and the amount of luggage into ac­
count when adjust ing tire pressu re for a trip -
even one that yo u wou ld not consider to be
" long." See
r=;, page 202, Tires and vehicle
load limits
for more important information.
Always use an accurate tire pressure gauge
when checking and adjusting inflation pres­
sures. Check all of the tires and be s ure not to
forget the spare tire. If the pressure in any tire
is too high when the tire is "cold," let air out
of the tire s low ly with the edge of the tire
gauge and keep checking the pressure until
you reach the pressure that is correct for the load (passengers and luggage) and kind of
dr iv in g you plan to do.
If the pressure in any tire is too low, note the
difference between the pressure in the cold
tire and the pressure you need and add the air
that you need to reach the correct pressure for
the vehicle load (passengers and luggage) for
the tires on your vehicle as listed on the on
your vehicle and in this manual and the kind
of driving you plan to do. .,..

Never exceed the m aximum inflati on pres­
s u re li sted on the ti re sidew all for any rea­
son.
Remembe r that the vehicle manufacturer, not
the t ire manufacturer, determines the co rrect
tire pressure for the tires on your vehicle.
It is importan t to check the tire pressure when
t he t ires are cold .
- Read the requ ired ti re pressure from the tire
pressure label located on d river's s ide B-pi l­
l ar .
- T urn the valve stem cap counter-clockwise
to remove it from the tire valve .
- Place the air pressure gauge on the valve .
- The tire pressures should only be checked
and adjusted when the tires are cold . The
s li ght ly raised p ressures of warm tires must
not be reduced.
- Adjust the t ire pressure to the load you a re
ca rrying.
- Re install the valve stem cap on the valve .
When should I ch eck the ti re pres sur e?
The correct tire pressure is especially impor­
tant at high speeds. The pressure should
therefore be checked at least once a month
and a lways before start ing a journey .
When should I ad just th e tir e pre ss ures?
Ad just the tire pressure to the load you are
carrying . After changing a wheel
or replacing
wheels you have to adjust the tire pressures
on all wheels. In addition, you must then in it i­
alize the new tire pressures in the tire pres ­
sure mon itor ing system
q page 212 .
A WARNING
Incorrect tire pressures and/or unde rinfla­
tion can lead sudden tire failure, loss of cont ro l, col lision, ser ious persona l inju ry
or even death.
- When the warning symbo l
[D] appears in
the instrument cl uster, stop and inspect
the tires.
- Incor rect tire pressure and/or underinfla­
tion can cause increased tire wear and
Tire s an d wheel s 201
can affect the handling of the vehicle and
stopping ability .
- Incorrect tire pressures and/or underin­
flation can a lso lead to sudden t ire fail­
ure, including a blowout and sudden de­
flation, caus ing loss of veh icle control.
- The driver is responsible for the correct
tire pressures for all tires on the veh icle.
The applicable pressure values are locat­ ed on a sticker on the dr iver's s ide B-pil ­
lar .
- On ly when all tires on the vehicle are fil­
led to the correct pressure, the t ire p res­
sure mon itor ing system can work cor­
rectly.
- The use of incorrect tire p ressu re va lues
can lead to acc idents or other damage.
Therefore it is essential that the drive r
observe the spec ified t ire p ress ure val ues
for the t ires and the correct pressures for
the function of the tire press ure monito r­
ing system.
-A lways inflate tires to the recommended
and correct tire pressure before dr iv ing
off.
- Driving with underinf lated tires bend
mo re, letting them get too hot resulting
in tread separation, sudden tire failure
and loss of control.
- Excessive speed and/over loading can
cause heat b uild-up, sudden tire failure
and loss of control.
- If the tire pressure is too low or too high,
the t ires will wear prematurely and the
veh icle w ill not handle well.
- If the tire is not flat and you do not have
to change a wheel immediately, drive at
reduced speed to the nearest service sta­
tion to check the t ire p ressu re and add
a ir as requ ired.
(D Note
Driving w it h out valve stem caps can cause
damage to the tire valves. To prevent this,
always make sure that factory installed
valve stem caps on all whee ls are secu rely
mounted o n the valve. .,.
•
•

202 Tires and wheels
@ For the sake of the environment
Underinflated tires will a lso increase the
fue l consumption.
Tires and vehicle load limits
There are limits to the amount of load or
weight that any vehicle and any t ire can carry.
A vehicle that is overloaded w ill not handle
well and is more difficult to stop. Overload ing
can not only lead to loss of vehicle control,
but can also damage important pa rts of the
vehicle and can lead to s udden tire failure, in­
cluding a blowout and sudden deflation that
can cause the vehicle to crash.
Your safety and that of your passengers a lso
depends on making sure that load limits are
not exceeded. Vehicle load includes everybody
and everything in and on the vehicle. These
l oad limits are technically referred to as the
vehicle's
Gross Vehicle Weight Rating
("GVWR").
The "GVWR" includes the weight of the basic
vehicle, all factory installed accessories, a full
tank of fuel, oil, coo lant and other fluids plus
maximum load. The maximum load includes
the number of passengers that the vehicle is
intended to carry ("seating capacity") with an
assumed weight of 150 lbs (68 kg) for each
passenger at a designated seat ing pos ition
and the total weight of any l uggage in the ve­
h icle.
The
Gross Axle Weight Rating ("GAWR") is
the maximum load that can be app lied at each
of the vehicle's two axles.
The Gross Vehicle Weight Rating and the
Gross Axle Weight Rating are listed on the
safety compliance stick er labe l located on the
driver 's side 8-p illar. Your Audi has 2 seat ing
positions. Each seating pos ition has a safety
be lt ¢
page 107, Safety belts.
The fact that the re is an upper limit to your
vehicle's Gross Vehicle Weight Rating means
that the tota l weight of whatever is being car­
ried in the vehicle is limited. The more passen­
gers in the vehicle or passengers who are heavier
than the standard weights assumed
mean that less weight can be carried as lug­
gage.
T he tire pressure label on your Audi also lists
the maximum combined weight of a ll of the
occupants and luggage or other cargo that
the vehicle can carry. For the location of the
label ¢
page 198, fig. 146.
A WARNING
Overloading a vehicle can cause loss of ve­
h icle control, a crash or other accident, se­
rious personal injury, and even death.
- Carrying more we ight than your veh icle
was des igned to carry will prevent the
veh icle from handling properly and in­
crease the risk of the loss of vehicle con­
trol.
- The brakes on a vehicle that has been
overloaded may not be able to stop the
veh icle w ithin a safe distance .
- Tires on a vehicle that has been overload­
ed can fail suddenly, including a blowout
and 5udden deflation, cau5ing lo55 of
control and a crash.
Determining correct load limit
Use the example below to cal­
culate the total weight of the passengers and luggage or oth­
er things that you plan to trans­
port so that you can make sure
that your vehicle will not be
overloaded.
Steps for Determining
Correct Load Limit
1. Locate the statement "THE
COMBINED WEIGHT OF QC­
CU PANTS AND CARGO
SHOULD NEVER EXCEED XXX .,..

204 Tires and wheels
c::>fig . 148 running across the tread. Depend­
ing on the make, there will be six to eight of
them evenly placed around the tire. Marks on
the tire sidewall (for example "TWI" or other
symbols) indicate the positions of the tread
wear ind icators . Worn tires must be replaced .
Different figures may apply in other countries
c::> ,& .
Tire pressure
Incorrect tire pressure causes premature wear
and can cause sudden tire blow-out . For this
reason, tire pressure must be checked at least
once a month
c::> page 200.
Driving style
Driving fast around curves, heavy acceleration
and hard braking increase tire wear.
Rotating tires for more even wear
For a ll four tires on your vehicle to have the
same service life, we recommend that the
front and rear tires are rotated according to
the tire manufacturer's suggested tire rota­
tion intervals. Please remember the follow­
ing:
- Tire rotation interva ls may differ from the
vehicle serv ice intervals outlined in your
Warranty
& Maintenance Booklet.
- The longer one tire is used in one location
on the vehicle, the more it wears at certain
points; therefore, we recommend that you
follow the tire manufacture r's suggested
t ir e rotation intervals .
- Vehicles with front-wheel drive experience
more tread wear on the front wheels com ­
pared to all-wheel drive (quatt ro ® ).
- Please rotate t ires as shown
c::> fig . 149.
-Extra care must be taken when rotating di-
rect ion-specific tires
c::> page 226.
Wheel balancing
The whee ls on new vehicles are balanced.
However, various situations during everyday
driving can cause them to become unbal­
anced, resulting in vibrations you can usually
feel through the steering wheel. Unbalanced
wheels must be rebalanced to
avoid excessive wear on steering, suspension
and t ires . A whee l must also be reba lanced
when a new tire is installed.
Incorrect wheel alignment
Incorrect wheel alignment can cause exces­
sive tire wear, impairing the safety of the vehi ­
cle. If tires show excessive wear, have the
whee l alignment checked by an authorized
Audi dealer or qualified workshop.
All Wheel Drive
Vehicles with quattro ® must a lways have tires
of the same size, construction and tread type .
For details see c::>page
154.
A WARNING
-Sudden tire fai lure can lead to loss of con-
trol, a crash and serious personal injury!
- Never drive a vehicle when the tread on
any tire is worn down to the wear indica­
tors.
- Worn tires are a safety hazard, they do not grip well on wet roads and increase
your r isk of "hydroplaning" and loss of
control.
- Always keep chemicals that can cause
tire damage, such as grease, oil, gasoline
and brake fluid away from tires.
- Tires age even if they are not being used
and can fail suddenly, especially at high
speeds. Tires that are more than 6 years
old can only be used in an emergency
and then w ith special care and at lower
speeds.
- Never mount used tires on your vehicle if
you are not sure of their "previous histo­
ry." O ld used tires may have been dam­
aged even though the damage cannot be
seen that can lead to sudden tire fai lure
and loss of vehicle control.

general, the greater the number of plies, the more weight a tire can support . Tire manufac­
turers also must indicate the materials in the
tire, wh ich include steel, nylon, polyester, and
others .
Ma ximum Load R ating
This number indicates the maximum load in
kilograms and pounds that can be carried by
the tire.
Tire qualit y gr ad ing for treadw ear,
tract ion , an d temp erature resis ta nce
Tread wear , traction and temperature grades
c::> pag e208.
M aximum Permis sibl e Inflation Pr essur e
This n umbe r is the greatest amount of air
pressure that should ever be put in the tire
under normal driving conditions .
& WARNING
- Using incorrect or unmatched tires and/
or whee ls or improper tire and whee l
combinations can lead to loss of contro l,
collision and serious personal injury.
- Always use tires, rims and wheel bo lts
that meet the specifications of orig inal
factory-installed tires or other combina­
t ions that have been spec ifically ap­
proved by the vehicle manufacturer .
- Tires age even if they are not be ing used
and can fail suddenly, especially at high
speeds . T ires that are more than 6 years
o ld can only be used in an emergency
and then with special care and at lower
speeds.
- Never mount used ti res on you r vehicle if
yo u are not s ure of their "previous histo­
ry ." Old used tires may have been dam ­
aged even though the damage cannot be
seen that can lead to sudden tire failure
and loss of vehicle control.
- All four wheels must be fitted with radia l
t ires of the same type, size (roll ing cir­
cumference) and the same tread pattern .
Driv ing with different tires reduces veh i-
Tire s an d wheel s 207
cle handling and can lead to a loss of
contro l.
- If the spare tire is not the same as the
tires that are mounted on the vehicle -
for examp le w ith winter t ires -only use
the spare t i re for a short period of time
and drive with extra care . Refit the nor ­
mal road wheel as soon as safely poss i­
ble .
- Never drive faster than the max imum
speed for which the tires on your vehicle
are rated because tires that are dr iven
faster than their rated speed can fa il
suddenly.
- Ove rloading tires cause heat build-up,
sudden tire fa ilure, including a blowout
and sudden deflation and loss of contro l.
- Temperature grades apply to tires tha t
are properly infla ted and not over or un­
derinf lated .
- For technical reasons it is not always
possible to use whee ls from other vehi­
cles -in some cases not even wheels
from the same ve hicle mode l.
-If you install wheel trim discs on the ve ­
hicle wheels, make sure that the air flow
to the brakes is not b locked. Reduced air­
f low to the brakes can them to overheat,
increas ing stopping d istances and caus­
ing a co llision .
- Run flat tires may only be used on vehi­
cles that were equ ipped w ith them at the
factory. The veh icle must have a chassis
des igned for run flat ti res and a factory­
installed t ire p ressure monito ring sys­
tem that indicates a loss of ti re p ressu re.
I nco rrec t use of run fl at tires can lead to
veh icle damage o r accidents. Check with
an authorized Audi dealer or tire special­ ist to see if your vehicle can be equipped
with run flat tires. If run flat tires are used, they must be installed on all four
wheels. Mixing tire types is not permit-
ted .
Ill>
•
•