2011 AUDI S8 door lock

_& WARNING
Not using a child safety seat, using the
wrong child safety seat or improperly in­ stalling a child restraint increases the risk
of serious personal injury and death in a
crash.
- Never install rear-facing child safety
seats or infant carriers on the front pas­
senger seat - even with an Advanced Air­
bag System. A child wilt be seriously in­
jured and can be killed when the inflat­
ing airbag hits the child safety seat or in­
fant carrier with great force and smashes
the child safety seat and child against
the backrest, center armrest, door or
roof¢
page 147, Child restraints on the
front seat -some important things to
know.
- Always install rear-facing child safety
seats or infant carriers on the rear seat.
- Never install a rear-facing child restraint
in the forward-facing direction. Such re­
straints are designed for the special needs of infants and very small children
and cannot protect them properly if the
seat is forward-facing.
- If you must install a rearward facing
child safety seat on the front passenger
seat because of exceptional circumstan­
ces and the
PASSENGER AIR BAG OFF
light does not come on and stay on, im­
mediately install the rear-facing child
safety seat in a rear seating position and
have the a irbag system inspected by your
Audi dealer.
- Always read and heed all WARNINGS
whenever using a child restrained in ave­
hicle is being used
¢page 137, Safety
belts,¢ page 145, Airbag system
and
¢ page 169, Important things to know.
Child Safety 175
Convertible child safety seats
Properly used convertible child safety seats
can help protect toddlers and children over
age one who weigh between 20 and 40 lbs. (9
and 18 kg) in a crash .
Fig. 159 Schematic overview: installat ion of the at­
tachments applicable to a LATCH seat
Fig. 160 Schematic overview: instal latio n of the seat
using the vehicl e's safety belt system
.,. When using the vehicle safety belt to install
a child safety seat, you must first activate
the convertible locking feature on the safety
belt to prevent the child safety seat from
moving <=>
page 178 or install the seat using
the LATCH attachments.
.,. Push the child safety seat down with your
full weight to get the safety belt realty tight
so that the seat cannot move forward or
sideways more than one inch (2.5 cm)
¢page 178.
.,. If the child safety seat is equipped with a
tether strap, attach it to the tether anchors
¢page 185.
A toddler or child is usually too large for an in­
fant restraint if it is more than one year old
and weighs more than 20 lbs. (9 kg).
Toddlers and children who are older than one
year up to about 4 years old and weigh more
~

-Always make sure that the safety belt re­
tractor is locked when installing a child
safety seat. An unlocked safety belt re­
tractor cannot hold the child safety seat
in place during normal driving or in a
crash .
- Always buckle the child safety seat firmly
in place even if a child is not sitting in it.
A loose child safety seat can fly around
during a sudden stop or in a collision.
- Always make sure that the rear seat
backrest to which the center rear safety
belt is attached is securely latched when­
ever the rear center safety belt is being
used to secure a child restraint.
- If the backrest is not securely latched,
the child and the child restraint will be
thrown forward together with the back­
rest and will strike parts of the vehicle
interior. The child can be seriously in­
jured or killed.
- Never install rear-facing child safety
seats or infant carriers on the front pas­
senger seat. A child will be seriously in­
jured and can be killed when the passen­ ger airbag inflates .
- The inflating airbag will hit the child
safety seat or infant carrier with great
force and will smash the child safety seat
and child against the backrest, center
armrest, door or roof.
- Always install rear-facing child safety
seats or infant carriers on the rear seat.
- Forward-facing child safety seats or in­
fant carriers installed on the front pas­
senger's seat may interfere with the de­
ployment of the airbag and cause serious
injury to the child.
- It is safer to install a forward-facing
child safety seat on the rear seat.
- Always read and heed all WARNINGS
whenever using a child restrained in ave­
hicle is being used
¢page 169. Special
precautions apply when installing a child
safety seat on the front passenger seat
¢ page 147, Child restraints on the front
seat -some important things to know.
Child Safety 1 79
A WARNING
-
Always take special precautions if you
must install a forward or rearward -facing
child restraint on the front passenger's
seat in exceptional situations:
- Whenever a forward or rearward -facing
child restraint is installed on the front
passenger seat, the
PASSENGER AIR
BAG OFF
light must come on and stay on
whenever the ignition is switched on.
- If the
PASSENGER AIR BAG OFF light
does not come on and stay on, perform
the checks described
¢page 156, Moni­
toring the Advanced Airbag System.
- Take the child restraint off the front pas­
senger seat and install it properly at one
of the rear seat positions if the
PASSEN­
GER AIR BAG OFF
light does not stay on
whenever the ignition is switched on.
- Improper installation of child restraints
can reduce their effectiveness or even
prevent them from providing any protec­
tion.
- An improperly installed child restraint
can interfere with the airbag as it de­
ploys and seriously injure or even kill the
child .
- Always carefully follow the manufactur­
er's instructions provided with the child
safety seat or carrier .
- Never place additional items on the seat
that can increase the total weight regis­
tered by the weight-sensing mat and can
cause injury in a crash.
A WARNING
Forward-facing child restraints:
- Always make sure the forward-facing
seat has been designed and certified by
its manufacturer for use on a front seat
with a passenger front and side airbag.
- Never put the forward-facing child re­
straint up, against or very near the in­
strument panel.
- Always move the passenger seat into its
rearmost position in the seat's fore and
aft adjustment range, as far away from •
•

180 Child Safety
the airbag as possible before installing
the forward-facing child restraint. The backrest must be adjusted to an upr ight
posit ion.
- Make sure that the
PAS SENGER AIR BAG
OFF
light comes on and stays on all the
t ime whenever the ignition is switched
on.
A WARNING , _
Rearward-fac ing ch ild restra ints:
- A ch ild in a rearward-facing child safety
seat installed on the front passenge r
seat will be ser iously injured and can be
killed if the front airbag inflates -even
with an Advanced Airbag System.
- T he inflating a irbag will hit the child
safety seat or infant carrier with g reat
force and w ill smash the ch ild safety seat
and child against the backrest, center
armrest, door or roof .
- Always be especially caref ul if you must
install a rearward facing child safety seat
on the front passenge r seat in exception ·
al circumstances .
- A tight tether strap on a rearward-facing
child restraint attached to the front pas­
senger seat can put too much pressure
on the weight-mat in the seat and reg is­
ter a heavier weight in the Advanced A ir­
bag System. The heav ier we ight regis­
tered can make the system work as
though an adult were on the seat and de­ ploy the Advanced Airbag when it must
be s uppressed causing ser ious or even
fatal injury to the child.
- Make sure that the
PASSENGER AIR BA G
OFF
light comes on and stays on all the
time whenever the ignition is switched on.
- If the
PA SSENGER AIR BAG OFF light
does not come on and stay on, immedi­
ately install the rea r-facing chi ld safety
seat in a rear seating position and have
the a irbag system inspected by your Audi
dealer.
Act ivating the convertible locking
retractor
Use the convertible locking retractor to se­
cure a child restraint.
Always heed the ch ild safety seat manufactur­
er's instructions when installing a child re­
st ra int in your vehicle. To activate the conve r­
t ible lock ing ret ractor:
.,. Place the ch ild restraint on a seat, prefera­
bly on the rear seat .
.,. Slowly pu ll the belt
all the wa y out .
.,. Route it around or through the child re­
straint belt path
¢ _& .
.,. Push the chi ld safety seat down with yo ur
full weight to get the safety be lt really tight.
.. Insert the belt tongue into the buck le for
that seating position.
.,. Guide the safety belt back into the retractor
until t he belt lies flat and snug on the child
safety seat.
.,. You should hear a "clicking" noise as the
be lt winds back into the inertia ree l. Test the
convert ible lock ing retractor by pulling on
the belt . You shou ld no longer be able to
pull the be lt out of the retractor. The con­
vertible locking retractor is now activated .
.. Make sure that the red release button is fac­
ing away from the child restraint so that it
can be unbuckled quickly.
.,. Pull on the belt to make sure the safety belt
is properly tight and fastened so that the
seat cannot move forward or sideways mo re
than one inch (2.5 cm).
A WARNING
-
Using the wrong child restraint or an im­
p roperly installed chi ld restraint can cause
serious personal injury or death in a crash.
- Always ma ke sure that the safety belt re-
tractor is locked when insta lling a child
safety seat . An un locked safety belt re­
tractor cannot hold the child safety seat in place dur ing norma l dr iving or in a
crash.

208 Cleaning and protection
-Never wash your car in bright sunlight.
Drops of water act as magnifying lenses
and may damage your paint.
- When you wash your car in the winter: if
you rinse your vehicle with a hose, be
careful not to aim the stream of water
directly at locks, or at door or hatch
openings - they can freeze shut.
- Never use sponges des igned to remove
i nsects, or any kitchen scouring sponges
or similar products . They can damage
your paint finish .
- Never use a dry cloth or sponge to clean
the headlights. Only use wet cloths or
sponges to prevent scratches .
It is best
to use soapy water.
- You should remove debris (such as in­
sects) from the headlight lenses on a
regular basis, fo r example when refuel­
ing your vehicle. Never clean the head­
lig hts w ith a dry cloth or sponge. Use a
wet cloth or sponge . It is best to use
soapy water.
@ For the sake of the environment
I n the interest of the environment, the ve­
hicle should only be washed in special
wash bays.
Washing your vehicle with a power
washer
Cleaning the exterior of your car with a high­
pressure power washer is safe as long as you observe a few simple rules.
• Before using the power washer, make sure
you have read and understood the WARN­
INGS
c:> A in General information on
page 206 .
• Always follow the operating instructions for
the power washer .
• Make sure that the jet on the spray hose pro­
duces a "fan shaped spray".
• Do
not hold the spray nozzle too close to
soft materia ls.
When cleaning the vehicle wit h a power wash­
er
always follow the operating instructions. T
his applies particu larly to the
operating
pressure
and the spraying distance. Keep a
distance from soft materials such as rubber
hoses or insulating material as well as sensors
and camera lenses.
Do not use a jet which sprays water in a
di rect
stream
or one that has a rotating jet .
Water temperature should not exceed 140 °F
(60 °().
A WARNING
Never wash tires with a jet that sprays wa­
ter in a direct stream . This could cause in­
v is ible damage to the t ires and weaken
them, even if the spray is from
a relatively
long distance and for a short time. Dam­
aged and weakened tires can fail and cause
accidents and personal injury .
(D Note
To avoid damaging your vehicle, always
make sure that there is suffic ient d istance
between the spray head and soft materials
like rubber hoses, plast ic parts and sound­
deadening materials as well as sensors
and camera lenses. Never aim the sp ray
head at the same point for a long time.
This also applies to cleaning headlights
and painted bumpers. Remember: the
closer the nozzle is to the surface of the
mater ia l, the greater the stress on the ma­
terial.
Sensors and camera lenses
- Remove snow with a hand brush and remove
ice with a de-icing spray that does not con­
tain solvents .
- Clean the sensors (adaptive cruise control*,
pa rking system*) w ith a cleaning so lution
that does not contain so lvents and a soft
cloth.
- The camera lens or the area in front of the
camera lens is normally cleaned by the
w indshie ld w ipers (Audi lane assist*) or
headlight wipers (night vision system*) . If
the lens or the area is exceptionally dirty,
111-

212 Cleaning and protection
tem pera ture is high, it can be removed with a
p lastic scraper and a suitable solvent.
A WARNING
So lvents can be dangerous.
- Benzine is flammable and toxic. If you
use benzine for removing the wax, keep
sparks, f lame and lighted cigarettes
away. Never dump benzine on the
ground, into ope n streams or down sew­
age drains .
- Be sure to observe all safety and env iron­
menta l regulations. Follow all instruc­
t ions on the container.
- Always read and heed all WARNINGS and
ot her information ¢
page 206.
Chassis
Have the undercoating checked for damage
from time to time.
The lower body shell of your Audi is a lso thor­
ough ly protected against corrosion.
Any damage to the under coating caused by
road hazards shou ld be repaired promptly.
A WARNING
Too much undercoating in the wrong pla­
ces can cause a f ire.
- Do not apply additional undercoating or
rustproofing on o r near the exha ust
man ifold, exhaust p ipes, catalytic con­
verter or heat shie lds. W hile driving, the
substance used for undercoating cou ld
over heat and cause a fire .
- Always read and heed all WARNINGS and
ot her information ¢
page 206.
Exhaust tail pipes
Road salt and other cor ros ive ma ter ials wi ll
damage th e material in the exha ust ta il p ipes
if they are no t cleaned reg ula rly. Do no t clean
the tail p ipes with whee l cleaner, p aint po lish ,
ch rome polish or ot her abrasive cleaners .
C lean the tail p ipes with car care prod ucts
that are s uita ble for stain less stee l. Your a
uthorized Audi dea ler can provide clean ­
ing products that have been tested and ap­
proved for yo ur vehicle.
Care of interior
Infotainment components
T he M MI/RS E* display may be cleaned wit h a
soft clot h and commerci ally-available " LCD
cl eaner". The clot h should be co ated lightly
whe n the cleaning solution when clea ning t he
display.
T he M MI/RS E* con trols m ust be cleaned first
with a b rush so tha t d irt does not en ter the
u nit or enter between the buttons and the
ho using. T hen wiping the cont ro ls with a cloth
dampened with dish detergent and water is
recommended.
(D Note
To prevent scratches, only clean the dis­
p lay when it is dry.
- To prevent damage, make sure fluids do
not enter the contro ls .
· Aluminum trim
U se only neutral -pH products to remove spots
and deposits from a luminum surfaces.
Chrome care products and a lkaline cleaners
will attack a luminum surfaces and can dam­
age t hem over t ime.
A WARNING
A lways rea d and heed all WAR NIN GS an d
o ther in fo rmation
¢page 206 .
Fabrics and fabric coverings
Fabr ics and fab ric cover ings (e.g . seats, door
trim pa ne ls, etc.) sho uld be cleaned at regular
intervals wit h a vacuum cleaner . This removes
s ur face dirt particles which cou ld become em­
bedded in the fabric throug h use. Steam
cleaners should not be used, because the
steam tends to push the dir t deeper into the
fabric a nd lock it the re . ..,_

216 Cleaning and protecti on
- To avoid damage, have stubborn stains
removed by a commercial cleaning spe­
cialist.
- Do not use br ushes, stiff sponges or sim­
ilarly abrasive cleaning aids.
Safety belts
Only well-maintained safety belts work relia ­
bly when needed .
> Keep belts clean.
> For cleaning, use a mild soap and wate r sol­
ution . Let be lts dry thoroughly and away
from direct sunlight .
> Do not allow inertia reel safety be lts to re­
tract before they are completely dry.
> Check the condition of your safety belts reg­
ularly .
Heavily soiled safety belts may not retract
properly.
.&_ WARNING
Damaged safety belts can break in a crash.
- Anything that might damage your safety
belts could mean that you and your pas­
sengers would not be adequately pro­
tected in an acc ident.
- Safety belt performance depends on cor­
rect installation. Never remove belts
from the vehicle to clean them.
- Do not use chemical cleani ng agents,
bleach or dyes. They have corrosive prop­
ert ies which weaken the webbi ng.
- When cleani ng your safety belts, inspect
them for damage.
If you discove r dam­
age, see you r A udi dealer.
- Always read and heed all WARNI NGS and
other information
c:> page 206.
Cooler
A ppl ies to vehicles: with cooler
A layer of ice or frost in the cooler interferes
with its cooling performance .
Clean ing
The refr igerator sho uld be cleaned reg ularly.
> Wash the coo ler with lukewarm wate r and a
mild cleaning solution, if necessary.
> Then wipe the cooler dry.
> Dust and d irt will accumulate near the venti­
lation openings in the luggage compart­
ment due to normal cooler usage. This
should be cleaned regularly.
D ef rosting
> Switch the coo ler off c:> page 72.
> Remove any food or beverages and allow the
coo ler to defrost with the door open.
> W ipe the inside of the cooler dry and clea n
the cooler, if necessary .
Defrost the cooler if you will not be us ing it
for extended periods of time .
(D Note
- Do not try to speed up the defrosting
process by apply ing heat.
- To reduce the risk of persona l injury or
damage to the refr igerator,
- do not use any abrasive cleaners, sol­
vents, wax, agg ress ive clean ing solu ­
tions, solut io ns w it h strong frag rances,
etc.,
- d o no t clean the co oler w ith cleaning
tools su ch as s teel woo l.
Engine compartment
Be especially careful when cleaning the en ­
gine comportment.
Alway s switch off the ignit ion b efor e cle an­
ing the engine
c:> ,&. .
Plenum panel
Remove leaves from the plenum panel in front
of the w indshield under the eng ine compart ­
ment . This prevents the wate r drain holes
from becom ing b locked, and it preve nts de­
br is from entering the vehicle inte rior through
the heat ing and ven tilat ion duc ts.
Corrosion protection
The eng ine compartment and transmission
have been corrosion-protected at the factory .
ll-

220 Fuel su ppl y and filli ng your fu el t ank
transport fue l to use for your lawn mower,
snow blower, etc., be very careful and al ­
ways observe local and state laws regard­
ing the use, transportat ion and storage of
such fuel containers . Make certain the con­
tainer meets industry standards (ANSI/
AS TM F852 - 86) .
(D Note
Never drive your vehicle until the fuel tank
is completely empty. The irregular supply
of fuel can cause misfiring . Gasoline could
enter the exhaust system and damage t he
catalyt ic converter.
Refuelling
Fig. 172 Rig ht rea r vehicle s ide: Ope ning t he fuel fille r
f lap
Fig . 173 Fuel filler fla p with attached fuel c ap
When activating the central locking, the fuel
fi ller flap is automatically un locked or locked.
Refue l the vehicle with the ignition switched
off.
Taking the fu el cap off
• Press the left side of the fuel filler flap to
open it
q fig . 172 -arrow-.
• Unsc rew fuel filler cap counter-clockwise
and hang it on the fuel fill er flap
¢ fig. 173 . Refuell
ing proc edur e
• Insert the fuel nozzle from the gasoline
pump into the fuel fi ller neck as far as it wi ll
go .
• Sele ct a med ium r efuelling rate so that the
no zz le switches off automatically when the
tank is full .
Putting th e fu el cap ba ck on
• After filling your tank, twist the fuel filter
cap clockwise as far as it w ill go.
• Close the fue l fill er flap.
T o avoid fuel spilling or evaporating from the
fuel tank always close fuel filter cap properly and completely. An improperly closed fuel fi ll­
er cap may also cause the MIL lamp
cc> page 2 7
to come on.
A WARNING
Improper refue ling or handling of fuel can
cause fire, explosion and severe burns.
- Fuel is highly flammable and can cause
severe burns and other injur ies .
- Fai lure to shut the engine off while refu­
eling and/or to insert the pump nozzle
fully into the fuel filter neck could cause
fuel to spray out of filler neck or to over­
flow. Fue l spray and overflowing fuel can
cause a fire .
- Never use a ce llular telephone whil e re­
fue ling . T he electromagnet ic rad iat io n
can cause sparks that can igni te fuel va­
pors and cause a fire.
- Never get back into your vehicle whi le re­
fuel ing.
If in exceptional circumstan ces
you must get back in your vehicle while
ref ueling, make certain that you close
the door and touch metal to discharge
static electricity before touching the fill­
er nozzle again . Static electricity can
cause sparks that can ignite fuel vapors
released during refueling .
- Never smoke or have an open f lame any­
where in or near your veh icle when refu­
eling or filling a portable fue l conta iner .
- For your safety, we strongly recommend
that you do not travel with a portable

fuel container in your vehicle. The con­
tainer, full or empty may leak and co uld
cause a fire, especially in a crash.
- If, under exceptional circumstances, yo u
must transport a portable fuel container,
please observe the following:
- Never fi ll a po rtable fue l container
while it is anywhe re in or on the vehicle
(for examp le, in the luggage compar t­
ment, or on the tr unk). Static electric i­
ty can bui ld up while fi lling and can ig­
n ite fue l vapors causing a fire .
- Always p lace a portable fuel container
on the gro und before filling.
- Always keep the fi ller nozzle comp lete­
ly inside the po rtable conta iner before
and during filling.
- If filling a portable container made of
metal, the filler nozz le must always be
in contact with the container. Th is w ill
he lp prevent static electricity from dis­
charging and cause a fire .
- Never sp ill fuel inside the vehicle or
luggage compartment. Fue l vapors are
h ighly f lammable .
- Always observe local and state/provi n­
cial laws regarding the use, storage
a nd tra nsporta tion of fuel co ntainers .
- Make certai n the fuel container meets
ind ustry standards (ANSI/ ASTM
F852 -86) .
(D Note
If any f uel has spilled onto t he car, it
should be removed immediate ly to prevent
damage to the paint.
~ For the sake of the environment
As soon as the correctly operated nozzle sw itches off automatically fo r the fi rst
time, the tank is full . Do not try to add
more fue l because fue l may spill out . In
add it io n, th e expans ion space in the fuel
t ank will be fi lled -cau sing the fue l to
overfl ow whe n it be come s w arm and pol ­
lu te the env iro nment.
Fuel suppl y and filling your fuel t ank 221
@ Tips
- Running your eng ine whi le refue lli ng
may cause vapors to escape or even
cause fuel to sp ill out of the tank. T his
would t hen shut off the fuel nozzle be­
f o re the ta nk is f ull.
- Do not refuel your vehicle with the ign i­
tion switched on. The fuel gauge may
ot herwise not ind icate the correct fue l
lev el after ref uell ing .
- The fue l filler flap of yo ur vehicle is not
locked when you lock t he veh icle from
t he ins id e.
Fuel filler flap emergency release
You can open the fuel filler flap by hand if the
power locking system should fail .
Fig. 1 74 R ig ht s ide tr im panel in t he luggage compart­
m en t: emerge ncy re lease mechan is m
The emergency release mechanism is located
behind the right side trim panel in the lug ­
gage compar tment .
.,. Loosen the loop
¢ fig. 174 from t he reta iner
and then pull on the loop carefully
¢ (D.
.,. Press on the left side of the fue l filler door
to open
¢ page 220, fig . 172 .
(J) Note
Only p ull on the loop until yo u feel res ist­
a nce . You w ill not hea r it release. Other­
wis e yo u could damage the eme rg ency re­
l ease mec hani sm .