2011 AUDI R8 SPYDER tire pressure

soon as possible, and inflate them to the
proper pressure. Driving on a significant ly un­
der-inflated tire causes the tire to overheat
and can lead to tire failure. Under-inflation a l­
so reduces fuel efficiency and tire tread l ife,
and may affect the veh icle 's handling and
stopping ab ility.
Please note that the TPMS is not a substitute
for proper t ire maintenance, and it is the dr iv­
er's responsib ility to ma inta in correct t ire
p ress ure , even if under- inflation has not
reached the leve l to t rigger illumination of the
TPMS low tire pressure telltale .
Your veh icle has also been equ ipped with a
TPMS malfunction indicato r to indicate when
the system is not ope rating properly. The
TPMS malfunc tion indica to r i s combined wi th
the low t ire p ressu re tell ta le. When the sys ­
tem detec ts a malf unct ion, the te lltale will
flash for approximately one minute and then remain continuo usly ill uminated . This se­
q uence will cont inue upon subsequent vehicle
start-ups as long as the ma lfunction ex ists.
When the malfunction indicator is ill uminat ­
ed, the system may not be able to detect or
signa l low t ire pressure as intended . TPMS
malfunct ions may occ ur for a variety of rea­
sons, including the ins talla tion of replace­
ment or alternate tires o r whee ls on the veh i­
cle that prevent the TPMS from funct io ni ng
p roperly . Always check the TPMS malfunct ion
t ellta le afte r replacing one o r more t ires or
wheels o n your veh icle to ensure tha t the re­
p lacemen t or a lternate tires and wheels allow
the TPMS to continue to function properly .
Introduction
The tire pressure monitoring system monitors
air pressure in all four road wheels while the
vehicle is moving .
As soon as the tire pressu re mo nitor ing sys­
tem senses a s ignificant loss o f air pressure in
one or severa l ti res, text messages and yellow
symbo ls appear in the instr ument cluster dis ­
p lay to alert the driver. The
[al warning light
Tire s an d wheel s 207
in the instrument cluster comes on when the
ti re is significant ly underinflated
Q page 34.
The wa rni ng lig ht [al also illu minates i n the
case of a system mal fun ct io n.
Be aware that t ire pressure is a lso dependent
o n the tempe ratu re of the t ire. For eve ry 18 ° F
(10 °C) incre ase in tir e te mper ature, tire pres­
s u re inc reases by about 1.5 psi (0 .1 bar). The
ti re warms up while the vehicle is moving and
ti re p ress ure rises . So you sho uld ad just tire
pressure only when they a re
cold, when the
temperature of the tires is roughly the same
as the ambient a ir temperature.
In order to keep the tire press ure monitoring
system p roperly ca librated, t ire press ure on
all four tires sho uld be checked at regu lar in­
terva ls.
The tire pressure is shown on the label located
on the dr iver's side B-pillar (v is ib le when the
door is open) .
A WARNING
When the tire pressure mo nitoring system
war ning light is lit , one o r more of your
tires is s ignificantly under-infla ted . You
shou ld stop and check your tires as soon as
pos sib le, and in flate t hem to the proper
p ress ure a s in dic ate d on the ve hicle's ti re
p ress ure lab el
¢page 19 3. D riving on a
significantly under -inflated ti re causes t he
tire to over heat and can lead to tire failure .
Under-inflat ion also is like ly to impair the
vehicle's handling and stopping ab ility.
@ For the sake of the environment
D riving wit h un der -inflated tires red uces
fuel efficiency an d tire t read life.
(D Tips
- E ach tire should be chec ked monthly
w hen the tem perature of the tires is
about the same as amb ient a ir tempera­
t u re and set to the recommended infla­
tion pressure as specified on the tire
pressure label
¢ pag e 193.
•
•

208 Tir es and whee ls
- The tire pressure monitoring system
helps the driver to keep an eye on tire
pressures. But the driver st ill has the re­
sponsibility for maintaining the correct
tire pressure.
- Tire pressure must only be adjusted
when the temperature of the tires is
about the same as ambient air tempera­
ture.
- When tires are replaced, the sensors and
valves should not be exchanged . The
valve core, nut, valve sealing and seal
washer (rep lacement kit) needs to be re­
placed. If necessary, the valve and the
whee l electronics have to be rep laced.
- The tire pressure monitoring system on
your Audi was calibrated us ing tires w ith
"RO" identification. We recommend us­
i ng these tires.
- If you should put different whee ls and
ti res on yo ur vehicle (e.g. w inter wheels
and tires), yo u m ust be certain that the
whee ls and tires are compatible with the
tire pressure monitoring system . Other­
wise the system w ill reg ister a ma lfunc­
tion and a fault message will be d is­
played . For more information, contact
your authorized Audi dealer .
- For Declaration of Compliance to United
States FCC and Industry Canada regula­
tions
~ page 212 .
Programming a new set of tires
App lies to vehicles: with tire pressure monitor ing system
When driving with a new set of ti res, you can
p rogram them to the t ire pres sure monitoring
system using the menu disp lay.
"' Turn the ign ition on .
"' Se lect the menu :
Set > Tir e pr ess ure >
Wheel chang e.
"' Confirm that you wo uld like to begin the
programming p rocess. The message
Wheel
s ens ors are being in it iali sed. Thi s m ay ta ke
a fe w minute s .. .
appears in the instrument
cluster disp lay. You can switch between programmed tire sets
at any time without reinitializing the system .
(D Tips
If the programming process was not com­
pleted successfully, the message
Wheel
s en sor s could not be initi alised
appea rs in
the disp lay and the
11118' indicator light
turns on. If this happens, repeat the pro­
cedure .

212 Consumer Information
malfunctions. Because of the way electronic
components are interconnected with each
other, such malfunctions can also have an ad­
verse affect on other systems that are not di­
rectly involved. This means that you risk both
a substantial reduction in the operational
safety of your vehicle and an increased wear of
vehicle parts~.&, .
Authorized Audi dealers will perform this
work in a professiona l and competent manner
or, in special cases, refer you to a professional
company that specializes in such modifica­
tions.
_& WARNING
Improper repairs and modifications can
change the way vehicle systems work and
cause damage to the vehicle and serious
personal injury .
(D Note
If emergency repairs must be performed
elsewhere, have the vehicle examined by
an authorized Audi dealership as soon as
possible.
Declaration of
Compliance, Telecom­
munication or
Electronic Systems
-
Radio Frequency Devices and Radiocommuni­
cation Equipment User Manual Notice.
The manufacturer is not responsible for any
radio or TV interference caused by unauthor­
ized modifications to this equipment.
Devices
The following devices each comp ly with FCC
Part 15.19, FCC Part 15.21 and RSS-Gen Issue
1:
-Cell phone package
- El ectronic immob ilizer
- Homelink® universal remote control
- Remote control key
- Tire pressure monitoring system
FCC Part 15.19
T his device complies with part 15 of the FCC
Rules. Operation is subject to the following
two conditions :
(1) This device may not cause harmful inter­
ference, and
(2) this device must accept any inte rfer ence
received, including interference that may
cause undesired operation.
FCC Part 15.21
CAUTION:
Changes or modifications not expressly ap­
proved by the party responsible for compli­
ance could void the user's authority to operate
the equipment.
RSS-Gen Issue 1
Operation is subject to the following two con­
ditions:
(1) this device may not cause interference,
and
(2) this device must accept any interference,
including interference that may cause unde­
sired operation of the device .

214 What do I do now?
Using TM S, tire damage caused by foreign
bodies up to about
0.16 inch (4 mm ) in diam­
eter can be sealed reliably.
The foreign object must s tay in the t ire.
The tir e sea lant mu st not be us ed :
- for cuts or punctures in the tire which are
larger than 0.16 inch (4 mm)¢ fig. 155
(D
- for damage to the rim@
- if you have been driving with very low tire
pressures or tires with no air @
Using the
TM S is described in the section
¢ page 214, Preliminary steps.
TMS can be used at temperatures down to -
4 °F (-20 °C).
A WARNING
Take the following precautions after re­
pairing the tire:
-
- Do not drive faster than SO mph (80 km/
h)!
- Avoid full-throttle acce leration, heavy
braking and fast cornering.
- The vehicle's road behavior can be affect­
ed.
- Tires sealed w ith
TMS are intended only
for
temporar y, short-te rm u se . Dam­
aged tires must be rep laced . Drive care­
fully to the next professional repair fa ­
cility.
- After using the tire sea lant the tire pres­
sure monitoring system may no longer
work properly. Drive carefully to the next professional repair fac ility.
- TMS must NOT be used,
- for cuts or pu nctures in the ti re whi ch
are larger than 0.16 inch (4 mm)
- for damage to the r im
- if you have been dr iv ing with very low
tire pressures or t ires with no air
- Seek profess ional assistance if it is not
poss ible to repair the tire with the tire
sealant.
- The tire sealant must not come into con­
tact with sk in, eyes or clothing. -
If you get any ti re sea lant in yo ur eyes or
come into contact w ith it, rinse the af­
fected area thoroughly with clean water. Find a phys ician immediately!
- Change any clothing contaminated with
tire sealant immediately.
- Do not inha le the vapor!
- If you have swallowed tire sealant, rinse
your mouth thoroughly right away and
drink plenty of water.
- Do not induce vomit ing! Find a physi­
c ian immediately!
- I f you have allergic react ions, find a
phys ic ian immediately.
- Keep the tire sealant away from children.
(D Note
Do not use commercially avai lab le tire
sealants. The e lectr ica l components of the
tire pressure monitoring system will no longe r work properly .
@) For the sake of the environment
Used sealant bottles can be dropped off at
a recycling facility.
(D Tips
- If sea lant has run out, allow it to dry.
Then you can peel it off.
- Have the t ire sea lant rep laced every 4
years at a dealership.
Preliminary steps
Some preliminary steps are necessary for tire
repair.
.. If you have a flat tire, park the vehicle as far
as possible from moving traffic .
.. App ly the
parking b rake firmly .
.. Engage a gear.
.. Check whether a repair using the Tire Mobili­
ty System is poss ible ¢ page 213 .
.. Have a ll passengers
leave the vehicle and
stay away from the danger zone¢.&_ .
.. Take the
se alant bottl e and the electric air
pump from the luggage compartment un-
de r the floor ¢ page 213, fig. 154. ...

.. Remove the "max. 50 mph" (80 km/h) stick­
er from the sealant bottle and affix it to the
instrument cluster in the driver's v iew .
A WARNING
-Turn the hazard flashers on if you have a
flat tire in moving traffic. In this way you
protect yourself and other road users.
- Make sure that all passengers are in a
safe place, out of the dange r zone (fo r
example, behind a guard ra il).
(D Note
Part icular care is necessary if you are mak­
ing a t ire repair on a steep incline.
@ Tips
Obey all laws.
Making a tire repair
Tire repair consists of the following sections.
F ig. 156 Parts of the Tir e Mob ility System
F ig . 1 57 Con nector for the Ti re Mob ility System
l) The e lectr ic a ir pump s houl d never r un for long er than
8 m inutes.
What do I d o now ? 215
Assembling Ti re Mobility System
.. Open the lid @of the ele ctr ic air p ump
<:!) fig. 156 .
.. Pull the plug @and the pressure hose®
w ith the gauge out of the housing .
.. Screw the pressure hose® of the electric
air pump onto the flange @ of the sealant
bott le @ .
.,. Push the sea lant bottle w ith the flange
down into the recess @ on the lid of the
electric a ir pump.
.. Remove the dust cap from the valve of the
defe ctive tire .
.. Screw the hose @onto the valve (?)
c::> fig. 157.
.. Insert the plug@<::> fig. 156 into t he socket
for the c igarette lighte r.
Inf lating tire
.. Move the switch @ .::!)fig. 15 7 on the elec­
tric air pump
l} to position I. After 5 mi­
nutes, tire pressure m ust have reached at
least 1.8 bar .
.. Switch t he e lectr ic air pump off -sw itch in
position
0 . If the required tire pressure of at
least 1.8 bar has not been reached, follow
th e instruct ions in the section
Re-inflating
tire .
Re-inflating tire
.. Remove the hose from the valve and pull the
plug out of t he socket .
.. Dr ive the veh icle slowly 10 meters backward
or forward . T his helps to distribute the seal­
ant bette r .
.. Remove the empty infla tion bottle and
s crew the hose ®®
c::> fig. 156 from the
electric pump directly onto the va lve .
.. Insert the plug@ into the socket for the
cigarette lighter .
.. Move the switch
@ Q fig. 15 7 on the elec­
tric air pump
l} to position I. After S mi­
nutes, tire pressure must have reached at
least 1.8 bar.

216 What do I do now?
• Switch the electric air pump off - switch in
position
0. If the required tire pressure of at
l east 1.8 bar has not been reached, it is not
poss ible to make a repa ir with the tire seal­
ant. Seek professional ass istance.
Di sas sembling T ire Mobilit y Sy stem
• Remove the hose from the valve and pull the
plug out of the socket.
• Screw the dust cap onto the valve.
• Place the empty sealant bottle back in the
original packaging and clip it in place under
the floor so that no tire sealant can run out into the vehicle .
• Start driving right away so that the sealant
is d istr ibuted in the tire.
.&_ WARNING
- Follow the manufacturer's safety instruc­
tions on the deca l for the air pump and
the sea lant bott le .
- If a tire pressure of 1.8 bar cannot be
achieved after pumping for S minutes,
the tire is too severely damaged. Do not continue to drive.
- Seek professional assistance if it is not
poss ible to repair the tire with the tire
sealant.
(D Tips
- Do not operate the electric ai r pump for
more than 8 min utes without stopping,
otherwise it can overheat. When the air
pump has cooled down, you can continue
to use it.
- If sealant has escaped, allow it to dry, then you can peel it off.
Final check
After driving for a short distance, t ire pressure
must be checked .
• After driving for about 10 minutes, stop and
check the t ire pressure.
• If tire pressure is still at least 1.3 bar, in ­
flate the t ire to specified pressure (see driv­
er's side B-pillar), dr ive to the next repair shop and have the tire and the sealant bot
­
tle replaced.
• If tire pressure is less than 1.3 bar, the t ire
is too severely damaged. Do not continue to
drive . Seek professional assistance.
.&_ WARNING
If t ire pressure is less than 1.3 bar after
d riving for 10 minutes, the t ire is too se­
ve rely damaged. Do not cont inue to drive.
See k professional ass istance.
(D Tips
After a tire repair, have the sealant bottle
r eplaced at a dealership. This restores full
funct ionality to the T ire Mobility System .
What should I be
aware of when
changing a tire?
Tires with unidirectional tread design
-
Tires with unidirectional tread design mu.st be
mounted with their tread pattern pointed the
right direction.
A un idirectional tire can be identified by ar­
row s on the sid ewall , which point in the di rec­
t ion of the rota tion. Yo u m ust follow the
speci fied direction o f rotation. This is necessa­
ry in order for these tires to develop t heir op ­
timum characteristics regarding grip, road
noise, wear, and hydrop lan ing .
· Anti-theft wheel bolts
A special adopter is needed to turn the anti­
theft wheel bolts.
Fi g. 158 Anti-theft wheel bolts w it h adapte r

Tightening wheel bolts
.,. Fit the wh eel b olt wrench ove r the wheel
bolt and push it down as far as it will go
1l.
.,. Close your grip around the
end of the
wrenc h handle fo r maximum torque and
turn each wheel bolt
clockwi se u nti l it sits
t ight.
H ave the
tightening torque of the whee l bolts
checked as soon as possible with a torque
wrench . It shou ld be 120 Nm.
Chec k the
tire pre ssure as soon as possible.
Return the vehicle tool kit to its proper place.
A WARNING
Loose ning t he wheel bo lts is prohib ited;
da nger of an accident!
@ Tips
- Never try and use the hexagona l socke t
i n the handle of the screwdr iver to loos­
en or tighten the w heel bolts.
- If yo u have dete rm ined t hat wheel bolts
a re cor roded and difficult to t urn, the
bo lts must be rep laced befo re checking
the to rque.
- Unti l the tig hte ning torque is checked,
d rive at redu ced speeds as a pre caution.
Notes on wheel change
Pl ease read the information¢ page 199, New
tires and replacing tires and wheels,
if you are
going to use a spare tire which is different
from the tires on your veh icle.
Afte r you change a tire:
- Check the tire pressure on the spare imme­
dia tely after mounting.
- Have the whee l bolt t ightening torque
chec ked w ith a torq ue wrench as soon as
poss ible by your author ized A udi dealer or a
qu alified service sta tion.
1 ) You need th e appropr iate adapter to tighte n the a nti­
t h eft wheel bolts
c:, page 216.
What do I do now? 219
- With stee l and alloy whee l rims, the whee l
bolts are correctly tightened at a torque of
90 ft lb (120 Nm) .
- If you notice while changing a tire that the
wheel bo lts are corroded and difficu lt to
turn, then they should be rep laced before
you check the tightening torque.
- Replace the flat tire with a new one and
have it installed on your vehicle as soon as
possible. Remount the wheel cover.
Until then , d riv e with e xtra care and at re­
duced speeds.
A WARNING
- If you are going to equ ip your vehicle
with tires or rims which differ from those
which were facto ry installed, then be
sure to read the information ¢
page 199,
New tires and replacing tir es and
wheels.
- Always sto re the tools secu rely in lug­
gage compartment. Othe rwise, in a n ac­
cident o r su dden maneuver they cou ld fly
forwdrd, CciU5ing injury to pd55enger5 in
the vehicle.
(D Note
Do not use comme rcially avai lab le tire
sea lants. Otherwise, the e le ctr ic al com po­
nen ts of t he tire p ressu re monitoring sys­
tem * wi ll no longe r work proper ly an d the
sensor fo r the tire pressure mon itor ing
system will have to be rep laced by a quali­
fied wor kshop.
Jump-starting
General
If necessary, the engine can be started by
connecting it ta the battery of another vehi­
cle.
If the engi ne should fail to start because of a
discharged or weak battery, the battery ca n be.,.. •
•

224 Fuses and bulbs
Fuse panel@
Consumer
Automatically dimming in-
side mirror, ga rage door
8 opener (Homel ink), washer
pump relay, power outlets
relay
10
~ button
11 Pressure sensor, climate
controls
12 Airbag
Fuse panel @
No . II Consumer
1 Radiator fan (1)
2 Radia tor fan (2)
3 Exterior lighting
4 Exterior lighting
6 Blower regulator
Fuse panel @
No . II Consumer
1 Rear view camera
2
Tire pressure monitoring
system
4
Cell phone package, te le-
phone antenna amplifier
5 Instrument cluster
6 Networking gateway
7 Steering column lever
8
Diagnostic interface, brake
pedal switch, selector lever
9 Rain/light sensor
10 Light switch
11 Special functions control
module
15 Sound amplifier
Radio
Fuse panel E
No. Consumer
3 Auxiliary water pump
5 Supply terminal 15, starter
Amps
10
10 5
5
II Amps
40 40
40
40
40
II Amps
5
10
7.5 5
5
5
10 5
5
5
30
20
Amps
10
30
Fuse panel @
No. Consumer
6 Pump for brake booster
7 Horn
8 Wiper motor
9 Wiper motor
10 Headlight washer system
12 Power outlets and cigarette
lighter
Fuse panel
®
No. !!Consumer
1
2
4
6
7
8
~~·
E lectronic Stabilization Pro­
gram
Electronic Stabilization Pro­
gram
Rear window defogger
Power locking system
Interior lights, washer noz­
zles
Anti-theft alarm sys tem
Climate controls
Heated seats
Lumbar support
11 Control module for doors
12 Control module for doors
Bulbs
Note
Amps
15
20
30
30
30
20
ll Amps ,
10
25
30
20
20
5
10
25 10
30 10
Your vehicle is equipped with maintenance­
free headlights and rear lights. However, if a
bulb has to be changed, please consult your
authorized Aud i dealer or other qualified
workshop .