2011 AUDI R8 SPYDER set clock

Instrument s and warning /indicator lights 11
Tachometer (engine rev counter)
The tachometer indicates the engine RPM
(revolutions per minutes) .
You should shift to the next lowest gear when
the speed is below 1500 RPM. The beg inning
of the red zone in the tachometer indicates
the maximum permiss ible engine speed for
all gears once the eng ine has been broken in
a nd when i t is wa rm. You sho uld shift to the
n ex t hi gher gea r, switc h the R tron ic sport
mode
off or remove your foot from the accel ­
erator pedal befo re reaching this a rea in the
ga uge.
(D Note
The needle in the tachometer~ page 10,
fig.
3 @ may only be in the red area of the
gauge fo r a short time or the engine could
be damaged. The location whe re the red
zone beg ins va ries depending on the en­
g ine.
Digital clock with date display
Your vehicle is equipped with a quartz con­
trolled digital clock.
F ig. 4 I n stru ment cl uste r w ith t he d ig ita l cl ock
D ate and time are set using the knob~ fig. 4.
To set the hour
• Pull the knob (hour d isplay flashes) and turn
it to the left o r rig ht.
To set the minutes
• Pull the knob as many times as necessary
u nti l the min ute display flashes .
• Turn the knob to the left or right.
To set the date
• Pull the knob a s many times as necess ary
until the day, month o r year disp lay flashes.
• Tur n the knob to the left or rig ht.
To hide or display the date
• Pull the knob as many t imes as necess ary
until the date di sp lay fla shes.
• Turn the knob to the le ft or rig ht.
Wh en th e date d isp lay s tops blin king, this
means the time and da te have been s uccess ­
f ully s to red.
Wi th the ig nition
off, push ing or pu lling the
Set/Che ck button
~ pag e 10, fig. 3@ can
tu rn o n the display field light ing for a few sec­
on ds.
Engine coolant temperature gauge
The engine coolan t ga uge ~ page 10, fig. 3@
onl y works when t he ig nition is on. To prevent
damage to your engine, please note the fol­
lowing important points.
Engine cold
As long as the need le remains a t the left end
of the gauge, the engi ne still has not reac hed
its operating tem perature. Avoid high eng ine
speeds, heavy engine loads and heavy throt­
tle.
Normal temperature
When the engine has re ached it s operat ing
temperature, the need le w ill move into the
midd le of the gauge and rema in the re .
If th e
engine is working hard at high outside tem­
peratures, the needle may turn further to the
right. This is no cause for concer n as long as
the . warn ing light i n the instrument clus ter
does not illuminate .
Warning light.
When the warning light .starts to flash, this
can mean one of two t hings : either the cool­
ant
temperature i s too h igh, or the coolant
l e vel is too low~ page 32 . IIJ,,

24 Driver information system
Menu display
Introduction
.____ __ ®
Fig. 13 Wiper lever: Controls for the men u disp lay
. Displa Type
~Set
!: Cfiecl< --,
Menu off
Fig. 14 Display: Start me nu
Some functions in your vehicle can be set, ac­
tivated, and controlled by
Menus (e.g. Acous­
tic park assist*). With these menus you can al­
so select the information shown in the Driver
Information System, which operates only with
the ign ition switched on . Operation is control­
led by the
I RESET ! button and the rocker
switch on the wiper lever¢ fig. 13.
The
Start menu shows you the different dis­
play types:
Set
Check
Menu off
Each display type in the Start menu contains a
submenu with additiona l opt ions .
Set Clock
¢page25
Computer
¢page25
Speed warning
¢ page29
Language
¢page25
Units (distance, fuel consump­
tion, temperature)
¢page25
Displays
Lights
¢ page55
Wipers (service position)
¢page 61
Doors (unlocking and locking
mode)
¢page39
Parking aid*
¢page89
Check Service
Chassis number
r::;, page 226
Keys
Menu off The menu display is hidden and
the lap timer appears.

30 Driver in formation system
To sto re ma ximum sp ee d
.. Turn off the ignit ion.
.. Briefly press the button in the instrument
cluster¢ page 29, fig. 26. The odometer
and the digital clock are now illuminated .
.. Press the button for at least 2 seconds. The
currently stored maximum speed appears in
the d isplay
or the crossed out symbol for
warning threshold 2, if no max imum speed
was set previous ly.
.. Press the fu nction selector sw itch in the
wiper lever@~ fig. 2 7 up or down to
change the set value. Val ues run up or down
in steps o f 6 mph (10 km/h) .
To delete maximum speed
.. Turn off the ignit ion.
.. Briefly press the button in the instrument
cluster~ page 29, fig. 26. The odometer
and the digi tal clock are now illuminated .
.. Press the button for at least 2 seconds. The
currently stored maximum speed appears in
the disp lay.
.. Press the
l ~R_E_S-E T~I button in the w iper lever
@ ¢fig. 2 7 until the crossed out speed
warning symbol for warning threshold 2 ap­
pears in the display.
A few seconds after the adjustment is com­
pleted, the illumination for the odometer and
the dig ita l clock will go out.
{D) Tips
This war ning threshold can also be con­
trolled through the trip computer
¢ page 25, Navigating the menu.
Warnings and symbols
Red symbols
A red symbol means DANGER.
.. Pull of the road and stop the veh icle.
.. Turn off the engine .
.. Check the ma lf u nct io ni ng system. Contact
your a uthorized Aud i dea ler o r a q ua lified
workshop for assistance.
-
USA mod els :
Ma lfunction in the brake sys-
tern
~page32
•
Canada mod els :
BRAKE
Malfunction in the brake sys-
tern
~page32
•
Engine coolant leve l too low/
COOL ANT engine coolant temperature
too high
~page32
Engine oil pressure too low
OIL PRES-¢page 33
SURE
When a red symbol appears, a warning tone
will sound three times in succession. The sym ­
bol cont inues to flash unt il the malfunction
has been repaired. If there is more than one
malfunction, the symbols appear one after
the other for about two seconds.
@ Tips
- The message for a malfunction can be
shown by pressing on the left knob.
- Dur ing route guidance on vehicles with a
navigation system, the warn ing symbol
is shown in the field above.
Yellow symbols
A yellow symbol means WARNING.
II
L ow fuel leve l
~page33
-
•
Check engine oil level
~page33
•
Engine oil sensor malfunction
¢page33
IJ
Worn brake pads
¢page33
•
USA models :
Speed warning 1
~page34
'

218 What do I do n ow ?
-On hard, slippery sur face (such as tiles)
use a rubber mat or similar to prevent
the jack from slipping.
- To help prevent injury to yourself and
your passenge rs:
- Do not raise the vehicle unti l you a re
sure the ja ck is sec urely engaged.
- Passenge rs must not rema in i n the ve­
h icl e when it is ja cked up.
- Make sure t hat passengers wait in a
safe p lace away from the vehicle and
well away from the road and traffi c.
- Make sure jack position is correct , ad­
just as necessary and then continue to ra ise the jack.
CD Note
A floo r jack or the pads on the hoist arms
m ust
n ot be posit ioned at the points
shown
-arrows-.
Remov ing the wheel
Follow these instructions step-by-step for
changing the wheel.
F ig . 161 Wh eel ch an ge : alignment pin in side the t op
hole
After you have loosened all wheel bolts and
ra ised the vehicle off the ground, perform the
following steps to remove and rep lace the
wheel :
Removing the wheel
" Use the
hexagon al socke t in the screwdri v­
e r handle
to comp letely turn out the top­
most wheel bolt and set it as ide on a
clean
surface . "
Sc rew the threaded end of the
al ignment
pin
from t he tool kit hand-tight into the
now vacant bolt ho le
c::> fig . 161.
" Then completely unscrew the other wheel
bolts as described above.
" Take off the whee l leaving the a lignment pin
in the bolt hole
c::> (D .
Putting on the wheel
"Lift the spare whee l and carefully s lide it
over the alignment p in to guide it in place
c::> (D .
" Use the hexagonal socket in the screwdriver
ha ndle to screw in and tighten a ll whee l
bolts
slightly .
"Unscrew the alignment p in and inse rt and
tighten the rema ining wheel bolt slightly
like the rest.
" Turn the jack hand le counter-clockwise to
lower the vehicle until the jack is fully re­
leased.
T he wheel bo lts must be clean and turn easily.
Check the contact s urfaces of whee l and hub .
Remove contaminants on these surfaces be ­
fore insta lling the wheel.
T he hexagonal socket in the screwdriver han­
dle makes it easier to handle the w heel bo lts.
The reversible blade shou ld be removed .
When mounting
u nidire ctional ti res, observe
the d irection o f rotation
c::> page 216.
CD Note
When remov ing or inst alling the whee l,
t he r im cou ld hi t the b ra ke ro tor and dam­
age the rotor . Work caref ully an have a
second person help you.
(D Tips
Never use the he xagonal socket in the han­
dle of t he screwdriver to loosen or tighten
the wheel bo lts .

236 Index
Parking systemadvanced
Switching on and
off ....... .... ... .. 91
Parts replacement ........... .. .... . 211
PASSENGER AIR BAG OFF light . . . . . . . . 128
Passive safety system . . . . . . . . . . . . . . . . . 99
Pedals .. .... .......... ...... ... .. . 104
Phys ica l pr inciples of a frontal collis ion . 111
Polishing .. .. ............. .. .. .. .. . 161
Pollen filter . . . . . . . . . . . . . . . . . . . . . . . . . 73
Power locking system ........ ... .... .. 39
Emergency locking .................. 42
Front lid . .... ........... .... .... .. 42
Locking .. .. ............. .. .. .. ... . 40
Locking and unlocking the vehicle from
inside ... .. ................ ... .. .. 41
Opening/clos ing the windows . .. .. .. .. 40
Sw itches . .. .. . .......... .. .. .... .. 41
Unlock ing .. .. . .......... .. .. .. .. .. 40
Power seats . . . . . . . . . . . . . . . . . . . . . . . . . 67
Power steering ................ .... . 1S4
Power windows ............. ... .. ... . 44
Power locking system . . . . . . . . . . . . . . . 40
Reactivating the system . .. .. .. .. .. .. 45
Pregnant women Special considerations when wearing a
safety belt . . . . . . . . . . . . . . . . . . . . . . . 114
Proper safety belt position . . . . . . . . . . . . 113
Proper seating pos ition
Driver ..................... ..... . 100
Fr ont passenger .............. .... . 101
Q
Quartz clock . . . . . . . . . . . . . . . . . . . . . . . . 11
R
Ra in sensor ............... .. .. .... .. S9
Defective .... ........... .. .. .. .. .. 35
Rear light Defective . . . . . . . . . . . . . . . . . . . . . . . . . 3 5
Rear spoiler . . . . . . . . . . . . . . . . . . . . . . . . 152
Warning/indicator light ...... .. .. .. . . 16
Rear view camera Parallel Parking .............. .... .. 92
Reverse parking .................. .. 92
Rear window . ... ....... ... .. .. .... .. 48 Rear
window defogger . . . . . . . . . . . . . . . . 76
Refueling ...... ... .. .............. . 172
Remote contro l
refer to Remote master key . . . . . . . . . . . 38
Remote contro l garage door opener
(Homelink ®) . ... .. ................ .. 95
Remote master key ...... ........... .. 37
Battery replacement . . . . . . . . . . . . 37, 38
Check light . . . . . . . . . . . . . . . . . . . . . . . . 3 7
Resetting the remote control . . . . . . . . . 38
Unlocking and locking .............. . 40
Repair manuals .. .. .......... ...... . 209
Rep lacement parts . ... .......... .. .. 211
Replacing Bu lbs ..... .... .. .. .............. . 224
Fuses ......... .. .. .............. . 223
Rims ......... .. ............. .... 199
Tires and wheels . ... .......... .. .. 200
Wheel rims .... .. ............. .... 201
Reporting Safety Defects . . . . . . . . 105, 106
Reset button . . . . . . . . . . . . . . . . . . . . . . . . 12
Retractor ... .... .. ............. .... 112
Reverse gear R tronic ........................... 85
Rims Replac ing . . . . . . . . . . . . . . . . . . . 199, 201
Rollbar
refer to Active rollover protection sys-
tem .. .. .. .... .. .. ...... .... ..... 107
R tronic ... ..... .. .. .............. .. 85
Description .... .. ................ .. 85
Gearbox malfunction ............. .. . 36
Kick-down . .... .. ............. .... . 87
Launch Control Program . .... ... .. .. . 87
Manual operation . .................. 86
Steering wheel with shift paddles ..... . 87
s
SAFE 12,38
Safe driving habits ................. .. 99
Safety belt position Safety belts worn by pregnant women 114
Safety bel t pretensione r
Service and disposal .............. . llS