2011 AUDI R8 SPYDER jump start

Safety belts . . . . . . . . . . . . . . . . . . . 109
General notes . . . . . . . . . . . . . . . . . . . . 109
Why safety be lts? . . . . . . . . . . . . . . . . 110
Ill ustrating the princ iple of an
accident . . . . . . . . . . . . . . . . . . . . . . . . 111
H ow are safety belts worn correctly? 112
Safety belt pretens ioners . . . . . . . . . . 115
Airbag system ........ .... ... .. 117
Important th ings to know . . . . . . . . . . 117
F ront airbags . . . . . . . . . . . . . . . . . . . . 121
M oni toring the Advanced Airbag
Sys tem . . . . . . . . . . . . . . . . . . . . . . . . . 128
Knee air bags . . . . . . . . . . . . . . . . . . . . . 132
Side airbags . . . . . . . . . . . . . . . . . . . . . 135
Child Safety ............. .. .. . .
Important things to know . ... .. .. . .
C hild safety seats . ..... ... .. .. .. . .
Instal ling a child safety seat . ... .. . .
Addit ional Information ........... .
Vehicle operat ion ..... .. .. .. . .
Intelligent technology .. .. .. . .
Not ice about data recorded by vehicle
control modules .......... .... .. . .
Electronic Stabilization Program ( ESP)
Rear spoiler .................... .
Braking .. .. .. ... ....... .... ... . .
P owe r stee ring .................. .
Driving w ith your qu attro ® ... .. .. . .
E ne rgy management ... ... .. .. .. . .
D ry s ump lubr ication ... ... .. .. .. . .
Driving and environment .... .
Break -in period . .. ..... ... .. .. .. . .
Driving through water on roads ... . .
Cata lytic converter ............ .. . .
Sporty driving . ........... .. .. .. . .
Operation and maintenance .. .. .. . .
Trailer towing ................... .
Vehicle care .................. .
Cleaning and protection ..... .
General information ...... .. .. .. . . 138
13
8
143
1 4 6
149
150
150
150
150
152
153
154
155
1 5 5
157
158 158
158
158
159
159 160
161
161
16 1
Ca re of exte rior . . . . . . . . . . . . . . . . . . 16 1
Ca re of inter io r . . . . . . . . . . . . . . . . . . . 165
Table of contents 3
Fuel supply and filling your
fuel tank ... .. .... . ... ...... ... .
170
Gasoline . . . . . . . . . . . . . . . . . . . . . . . . 170
Fuel tank. . . . . . . . . . . . . . . . . . . . . . . . 171
Checking and filling ..... ... .. .
Engine compartment lid .......... .
Engine oil ... .. .. .. . ............ .
E n gine cooling system ............ .
Brake fluid .. .. .. .. . .. .... ...... .
Battery ......... .. ............. .
Rep lacing the battery ............ .
Windsh ie ld washer container
Tires and wheels ... ..... ... .. .
175
175
178
181
184
184
18 7
188
189
T ires . . . . . . . . . . . . . . . . . . . . . . . . . . . 189
T ire pressure mo nitoring system
Consumer Information ...... .
Warranty coverages .............. .
Operating your veh icle outs ide the
U .S .A . or Canada ... . .. .. ..... ... .
A udi Se rvice Repair Manuals and
Literature . .. .. .. .... ........... .
Maintenance . .. .. .. ............. .
Additional accessories, modif ications
and parts rep lacement ........... .
Decla rat io n of Compliance,
T elecommunication or Electron ic
Systems .. .. .. .. .. ............. .
Do-it-yourself service ........ .
What do I do now? ........... .
Tru nk escape handle ........... .. .
B reakdown kit ... .. . .. ... .... ... .
Tire repa ir ... .... .. . .. .. ..... ... .
What shou ld I be awa re of when
h . t
' ? c anging a ,re. . . ............... .
Jump-starting .. ...... ........... .
Emergency towing with commercial
tow truck ....... .. ............. .
Fuses and bulbs .............. .
Electr ica l fuses .... .............. .
Bu lbs ... .. .. .. .. .. . .. .... ...... . 206
209
2
09
209
209
209
211
2 12
213
213
2 13
213
213
216
219
222
223
223
224
•
•

186 Checking and filling
-When disconnecting the battery, first
disconnect the negative cable and then
the positive cable.
- Before reconnecting the battery, make
sure all electrical consumers are switch­ ed off. Reconnect the positive cable first
and then the negative cable. Never inter­
change the cables -this could start a fire!
- Never charge a frozen or a thawed-out
battery. It could explode!
If a battery has
frozen, then it must be replaced. A dis­
charged battery can freeze over at 32 °F
(0 °C).
-Make sure the vent hose is always attach­
ed to the opening on the side of the bat­
tery.
- Never use batteries which are damaged.
Danger of explosion! Always replace a
damaged battery .
.&, WARNING
California Proposition
65 Warning:
- Battery posts, terminals and related ac­
cessories contain lead and lead com­
pounds, chemicals known to the State of
California to cause cancer and reproduc­
tive problems. Wash hands after han­
dling.
(D Note
- Do not disconnect the vehicle battery
when the ignition is switched on or when
the engine is running, otherwise, you will
damage electronic components in the
electrical system.
- If your vehicle is going to stand for a
long period of time without being driven,
protect the battery from "freezing", oth­
erwise it will be damaged and will then have to be replaced. Charging the battery
Connections for
charging the battery are lo­
cated in the luggage compartment.
Fig. 147 L uggage compartment: battery cover
Fig. 148 Luggage compartment: connectors for a
charger and jump start cables
Do not connect the negative cable directly to
the negative terminal on the battery. Connect
it to a
jump start pin instead c:, fig. 148.
.,. Always read and heed all WARNINGS c:, A
in Working on the battery on page 185 and
¢ A -
... Switch off the ignition and all electrical con­
sumers .
.,. Open the luggage compartment lid
c:>page42 .
.,. Remove the battery cover c:, fig. 147.
.,. Connect the terminal clamps from the
charger to the battery terminal (red= "posi­
tive") and the jump start pin
c:, fig. 148
(black or brown= "negative") as specified.
.,. Only now plug the mains lead for the charg­
ing equipment into the wall outlet and turn
it on .
.,. When the battery is fully charged: Turn the
charging equipment off and remove the
mains lead from the wall outlet .
.,. Now remove the clamps for the charging
equipment.

Tightening wheel bolts
.,. Fit the wh eel b olt wrench ove r the wheel
bolt and push it down as far as it will go
1l.
.,. Close your grip around the
end of the
wrenc h handle fo r maximum torque and
turn each wheel bolt
clockwi se u nti l it sits
t ight.
H ave the
tightening torque of the whee l bolts
checked as soon as possible with a torque
wrench . It shou ld be 120 Nm.
Chec k the
tire pre ssure as soon as possible.
Return the vehicle tool kit to its proper place.
A WARNING
Loose ning t he wheel bo lts is prohib ited;
da nger of an accident!
@ Tips
- Never try and use the hexagona l socke t
i n the handle of the screwdr iver to loos­
en or tighten the w heel bolts.
- If yo u have dete rm ined t hat wheel bolts
a re cor roded and difficult to t urn, the
bo lts must be rep laced befo re checking
the to rque.
- Unti l the tig hte ning torque is checked,
d rive at redu ced speeds as a pre caution.
Notes on wheel change
Pl ease read the information¢ page 199, New
tires and replacing tires and wheels,
if you are
going to use a spare tire which is different
from the tires on your veh icle.
Afte r you change a tire:
- Check the tire pressure on the spare imme­
dia tely after mounting.
- Have the whee l bolt t ightening torque
chec ked w ith a torq ue wrench as soon as
poss ible by your author ized A udi dealer or a
qu alified service sta tion.
1 ) You need th e appropr iate adapter to tighte n the a nti­
t h eft wheel bolts
c:, page 216.
What do I do now? 219
- With stee l and alloy whee l rims, the whee l
bolts are correctly tightened at a torque of
90 ft lb (120 Nm) .
- If you notice while changing a tire that the
wheel bo lts are corroded and difficu lt to
turn, then they should be rep laced before
you check the tightening torque.
- Replace the flat tire with a new one and
have it installed on your vehicle as soon as
possible. Remount the wheel cover.
Until then , d riv e with e xtra care and at re­
duced speeds.
A WARNING
- If you are going to equ ip your vehicle
with tires or rims which differ from those
which were facto ry installed, then be
sure to read the information ¢
page 199,
New tires and replacing tir es and
wheels.
- Always sto re the tools secu rely in lug­
gage compartment. Othe rwise, in a n ac­
cident o r su dden maneuver they cou ld fly
forwdrd, CciU5ing injury to pd55enger5 in
the vehicle.
(D Note
Do not use comme rcially avai lab le tire
sea lants. Otherwise, the e le ctr ic al com po­
nen ts of t he tire p ressu re monitoring sys­
tem * wi ll no longe r work proper ly an d the
sensor fo r the tire pressure mon itor ing
system will have to be rep laced by a quali­
fied wor kshop.
Jump-starting
General
If necessary, the engine can be started by
connecting it ta the battery of another vehi­
cle.
If the engi ne should fail to start because of a
discharged or weak battery, the battery ca n be.,.. •
•

220 What do I do now?
connected to the battery of another vehicle,
using a pair of jumper cables to start the en­
gine.
Both batteries must be rated at 12 volts. The
capacity (Ah) of the booster battery must not
be substantially less than the capacity of the
discharged battery.
Jumper cables Use
only jumper cables of sufficiently large
cross section to safely carry the starter cur­
rent. Refer to the manufacturer's specifica­
tions.
Use only jumper cables which have
insulated
terminal clamps and are properly marked for
distinction :
plus(+) cable: in most cases colored red
minus(-) cable: in most cases colored black
A WARNING
Batteries contain electricity, acid, and gas .
Any of these can cause very serious or fatal
injury. Follow the instructions below for
safe handling of your vehicle's battery.
- Always shield your eyes and avoid lean­
ing over the battery whenever possible.
- A discharged battery can already freeze
at temperatures just below 32 °F (0 °C).
Before connecting a jumper cable, the
frozen battery must be thawed com­
pletely, otherwise it could explode.
- Do not allow battery acid to contact eyes
or skin. Flush any contacted area with
water immediately.
- Improper use of a booster battery to
start a vehicle may cause an explosion.
- Vehicle batteries generate explosive gas­
es. Keep sparks, flame and lighted ciga­
rettes away from batteries.
- Do not try to jump start any vehicle with
a low acid level in the battery.
- The voltage of the booster battery must
also have a 12-Volt rating. The capacity
(Ah) of the booster battery should not be
lower than that of the discharged bat­
tery. Use of batteries of different voltage or substantially different
"Ah" rating
may cause an explosion and personal in­
jury.
- Never charge a frozen battery. Gas trap­
ped in the ice may cause an explosion.
- Never charge or use a battery that has
been frozen . The battery case may have
be weakened .
- Use of batteries of different voltage or
substantially different capacity (Ah) rat­
ing may cause an explosion and injury.
The capacity (Ah) of the booster battery should not be lower than that of the dis­
charged battery.
- Before you check anything in the engine compartment, always read and heed all
WARNINGS
9 page 175, Working in the
engine comportment.
(!) Note
-Applying a higher voltage booster bat ­
tery will cause expensive damage to sen­
sitive electronic components, such as
control units, relays, radio, etc.
- There must be no electrical contact be­
tween the vehicles as otherwise current
could already start to flow as soon as the
positive(+) terminals are connected.
(D Tips
- The discharged battery must be properly
connected to the vehicle's electrical sys­
tem.
- Switch off any car phone, or follow the
car phone instructions for this situation.

Use of jumper cables
Make sure to connect the jumper cable
clamps in exactly the order described below'
Fig . 162 Luggage co m pa rtme nt: connec tor s for a
ch arge r and jump start cab les
F ig . 163 Ju m p sta rt usin g t he batte ry in a not her ve hi­
cl e: A -Fem ale socket , B · Dis charge
The batte ry is located in the luggage compart­
ment ¢
page 185. The front lid can be opened
in an emergency
C? page 43 .
Do not connect the negat ive cable directly to
the negative termina l on the battery. Connect
it to a
j u mp start pin instead ¢ fig. 162.
Connect the posi tive cable (red) to the
posit ive t ermin al
1. Connect one end of the red jumper cable
¢
fig. 163 (D to the positive te rm inal of
d ischarged battery @.
2. Connect the other end of the red jumper
cable to the positive termina l@ of the
booster battery @.
Conn ect the negat ive cable (black ) to the
n egati ve ter minal
3. Connect one end of the black jumper ca­
b le @ to the negative terminal of the
booster battery @.
What do I d o now ? 221
4. Secure the other end to the jump start pin
@for the discharged battery @.
Starting the engine
~ Start the engine of the veh icle providing as­
sistance and al low it to run at idle.
~ Now sta rt the engine of the vehicle with the
discharged battery .
~ If the engine does not start: Stop trying af­
ter 10 seconds and then try again after
about 30 seconds.
~ Disconnect the cable while the engine is
running in exactly
reverse order to that de ­
scribed .
The ba ttery is ven ted to the ou tside to prevent
gases from entering the vehicle interior . Make
sure that the jumper clamps are well connect­
ed with their
metal parts in full contact with
the battery term inals .
.&, WARNING
To avoid serious personal injury and dam­
age to the veh icle, heed all warnings and
instructions o f the jumper cable manufac­
turer . If in doubt, call for road service.
- Ju mper cables m ust be long enough so
that the vehicles do not touch.
- When connecting jumper cables, make
sure that they cannot get caught in any
mov ing parts in the engine compart­
ment.
- Before you check anything in the engine
compartment, always read and heed a ll
WARNINGS ¢
page 175, Working in the
engine compar tment.
(D Note
Improper hook-up of jumper cables can ru ­
in the generator .
- Always connect POSITIVE(+) to POSI ­
TIVE(+), and NEGATIVE( -) to NEGATIVE
( - ) ground post of the battery manager
control unit.
- Check that all screw p lugs on the battery
cells are screwed in firm ly. If not, tighten
plugs prior to connecting clamp on nega-
-
tive battery terminal. .,..

222 What do I do now ?
-Please note that the procedure for con ­
necting a jumper cable as described
above applies spec ifically to the case of
your vehicle be ing jump started. When
you are giving a jump start to another ve­
hicle, do
not connect the negative( -) ca­
ble to the negat ive( -) terminal on the
discharged battery ©-Instead, securely
connect the negative (- ) cable to either a
solid metal component that is firmly
bo lted to the engine b lock or to the en­
gine block itself . If the battery that is be ­
ing charged does not vent to the outside,
escaping battery gas cou ld ign ite and ex­
plode!
Emergency towing
with commercial tow
truck
General hints
Your Audi requires special handling for tow­
ing.
The following information is to be used by
commercia l tow truck operators who know
how to operate their equipment safely.
- Never tow your Audi, towing will cause dam­
age to the engine and transmission .
- Never wrap the safety chains or winch cables
around the brake lines.
- To prevent unnecessary damage, your Audi
must be transported with a car carrier (flat
bed truck).
- To load the vehicle on to the flat bed, use
the towing loop found in the vehicle tools
and attach to the front anchorage
~ page 222.
A WARNING
A vehicle being towed is not safe for pas­
sengers. Never allow anyone to ride in a
vehicle being towed, for any reason.
(D Note
The vehicle has very low ground clearance.
Make sure that no damage is caused to the
-
underside of the vehicle when it is being
loaded onto a f lat bed truck .
Front towing loop
Do not install the front towing loop until it is
needed.
Fig. 164 Right front bumper without grille : Tow ing
loop
fully screwed in
On the right front in the bumper, there is a
threaded hole behind the air intake grill into
which the towing loop is screwed.
"' Remove the towing loop from the vehicle
tool kit~
page 213.
"'Pull the lower part of the grill forwa rd and
out .
"' Screw the towing loop tightly into the
threaded ho le as far as it wi ll go ¢
fig. 164.
When it is no longer needed, unscrew the
towing loop and put it back into the on-board
toolkit. Make sure to have the towing loop stored in the vehicle at all times.
When installing the grill for the air duct, be
sure that the tabs on the grill are first insert­ ed into their guides on the vehicle. Then push
the grill into position.
A WARNING
= If the towing loop is not screwed in as far
as it will go, the thread can pull out when
the veh icle is towed -potential r isk of an
accident.
@ Tips
Check carefully to make sure the hook-up i s secure.

234 Index
Fuel gauge . . . . . . . . . . . . . . . . . . . . . . . . . 12
Fue l ra nge . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Fuses Assig nment ................. .... . 223
Replacing ............... ...... .. . 223
G
Garage door opener . . . . . . . . . . . . . . . . . . 95
Genera to r
Warn ing/ indicato r ligh t .. .. .. .. .... .. 17
Glossary of t ire and load ing te rm ino logy 190
Glove compartment . . . . . . . . . . . . . . . . . . 70
Gross Veh icle Weight Ra ting (GVWR) ... 226
H
Headlig ht
D efect ive . . . . . . . . . . . . . . . . . . . . . . . . . 3 5
H eadlig ht flasher . . . . . . . . . . . . . . . . . . . . 58
Headlights . . . . . . . . . . . . . . . . . . . . . . . . . 55
H ead restraints . . . . . . . . . . . . . . . . . 68, 102
Ad justing ........................ 102
Heated Outside mirrors . . . . . . . . . . . . . . . . . . . . 63
Rear window defogger . . . . . . . . . . . . . . . 76
Seats .. .. .. ... .... ...... ... ... .. .. 76
Washer jets . . . . . . . . . . . . . . . . . . . . . . . 59
Heating . .... .. . .......... .. .. .... .. 72
H igh beam . . . . . . . . . . . . . . . . . . . . . . 5 5, 58
War ning/indicato r lights ... .. .. .... .. 16
H igh voltage wa rn ing la bel ....... .... 226
Hill hold assist
Starting on hills .......... .... .... .. 80
H ome link ® .. ... .. ..... ... .. .. .... .. 95
H orn ... .. .. ... .... ...... ... ... .. .. . 8
How many airbags does my vehicle have? 124
H ow often s houl d I check my t ire pres-
sures? .... .. ... ... .... ... .. .. .... . 195
H ow safety belt pretensioners work . ... 115
H ydroplaning . .. . ...... ... .. .. .... . 199
I
Ignition . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
Immobilizer .... .... ...... ... ... .. .. 1 2
Important things to do before driving . . . 99 Improperly worn sa
fety belts . . . . . . . . . . 11 4
Ind icator lig ht
Airbag system ................ .... 1 28
Cl ut ch overheat ing ............. .. .. . 36
C onvertib le top ................... . 16
No reve rse gear .. .. ... ..... ... .. .. . 35
PASSENGER AIR BAG OF F ..... ... . .. 128
Se lector lever defective . ..... ... .. .. . 35
In dic ator lights ...................... 14
Re d symbo ls in the ce nte r display . . . . . . 30
Ye llow symbo ls in the center display . .. 30
Infant seats ....................... 143
Installing child safety seats
Safety belts . . . . . . . . . . . . . . . . . . . . . . 146
Instrument clus ter and con trols ... .. .. . 10
Instr ument panel ill umination ...... .. . 56
Instr uments and controls
Genera l illustration . . . . . . . . . . . . . . . . . . 8
Interior ligh ts . . . . . . . . . . . . . . . . . . . . . . . 58
L uggage compartment . . . . . . . . . . . . . . 59
Intermittent wiping . . . . . . . . . . . . . . . . . . 59
J
Jump-start ing . ... . ... ... .... ... .. .. 219
K
Key ................................ 37
Battery replacement ........... ..... 38
Emergency key . . . . . . . . . . . . . . . . . . . . . 3 7
K ey replacemen t ................. .. 37
Remote maste r key . . . . . . . . . . . . . . . . . 3 7
K ick-down
R tronic ....... .. ................. . 87
K nee a irbags . ..... ... .. ..... ... .. .. 132
Desc ription .... .. .. ... ..... ... .. .. 132
How they wor k ... ... .. ..... .... . .. 134
Important sa fety instructions ........ 134
L
Lap timer
Delet ing total resu lts . ... .... ... .. .. . 28
Display ing split time ................ 27
Ending timing . . . . . . . . . . . . . . . . . . . . . 28
Eva luating times . . . . . . . . . . . . . . . . . . . 28
Interrupting timing ................. 27
Introduction ... .. .. ... ....... ... .. . 26