2011 AUDI R8 SPYDER sensor

60 Clear v is ion
Moving w iper blades to the service
posit ion
.. Do not lift the wiper arms away from the
glass when they are in their parked position;
this would damage the paint on the front
lid .
.. When there is a risk of frost, make sure that
the wiper b lades are not frozen to the wind­
shield .
.. Move wipe r blades to the se rvice posit ion
¢page 61.
The windshield wipers and washer on ly work
when the ignition is turned on.
To reduce the sensit iv ity of the sensor, move
switch @down . To increase the sens itiv ity,
move the switch up. The higher you adjust the
sens itivity, the faste r th e sensor will react
when it senses moisture on the w indshield.
The pauses between w iper turns depend not
on ly on the sensitivity setting, but on the ve ­
hicle speed as well.
Du ring a temporary stop, e.g . at a t raff ic sig­
na l, the set wipe r speed is automatically re­
duced by one stage.
When the igni tion is tu rned on, the washer
jets are heated.
_& WARNING
- Wipe r blades a re cruc ial for safe driving!
Only when they are in good cond ition are
they able to clear the windows properly
to provide uncompromising visibility.
Worn or damaged wiper blades are a safety hazard ¢
page 61, Replacing
front wiper blades!
- The light/ra in sensor is only des igned to
assist and support the dr iver .
It remains
entirely the d river 's responsibility to
mon itor outs ide weather conditions and
to manually activate the w ipers as soon
as rain o r dri zzle red uces visibi lity
thro ugh t he windshie ld.
- T he windshie ld must not be treated with
water-repe llent materials. They can in­
crease glare under poor visib ility condi­
tions such as wetness, darkness, or when the s
un is low on the horizon . In addi­
tion, they can cause the w indshield w ip­
ers to chatter .
(D Note
In freezing or near freezing conditions:
- Always check that the w iper b lades are
not frozen to the g lass before you turn
the wipers on . Loosen a wiper blade
wh ich is frozen in place before operating
the wipers to prevent damage to the
w iper blade or the wiper motor.
- Do not use the w ipers to clear a frosted
window. Us ing the wipers as a conven­
ient ice scraper will destroy the wiper
blades .
- Before you take your veh icle to an auto­
matic car wash, make sure you have the
w indshield w iper system switched off
(lever in position 0), otherwise the w ind­
shield w iper system could get damaged
in the car wash if it should suddenly
come on .
(D Tips
-The windshie ld w ipers are switched off
w hen the ignit ion is turned off. Act ivate
t he winds hield wipers after the igni tion
is switched back on by moving the wind­
shield wiper lever to any position.
- Worn or d irty windshield wipe r blades
cause smearing, which can affect the op­
eration of the light/rain sensor . Check
the cond ition of your windsh ield wiper
blades regularly.
- When the wipers are switched on man­
ually and in ra in cond itions, the auto­
matic headlights turn on
¢ page 55 or
off during the day when the wipers are
no longer operating . The automat ic
head lights fu nction is avai lab le in this
case on ly w hen the light switch is in the
"A UTO" posit ion ¢
page 55, fig. 63.
-Make su re the washer fluid reservoir is
t opped off before goi ng on a long tr ip.
Look up ¢
page 188 for checking and
filling the washe r containe r.

-If you switch off the ignition w ith the
windshield wiper lever still in the inter­
val w ipe pos ition and then come back a
while later and dr ive off , the rain sensor
will reactivate itself after the vehicle
speed has exceeded 4 mph (6 km/h) .
Service position
It is only possible to change wiper blades if
you move the wiper arms to the service posi­
tion .
In order to use the windshield wipers, the
front lid must be comp letely closed.
Moving w ipe r blade s to the service
position
.. When there is a risk of frost, make sure that
the wiper b lades are no t frozen to the wind­
shield .
.. Switch the ign ition on .
.. Move the wiper lever to pos ition
0
c::> page 59, fig. 69 .
.. Press the I RESE T I button unt il the Display
type
menu appears in the Driver Informa­
tion System display .
.. Using the rocker switch and the
!RESET I b ut­
ton, select the
Set > Wiper s > Front > Serv ­
ic e position on
function . The wind sh ield
wiper arms move to the service pos it ion.
Moving w ipe r blade s to park po siti on
.. Make certain that the wiper arms are ly ing
against the w indshie ld .
.. Switch the ignition on and move the wipe r
lever from position
O to 4 c::> page 59 ,
fig. 69. The wiper arms will move back to
t h e park pos ition .
(D Note
Never drive your vehicle when the wind­
shield w iper arms are in the service pos i­
tion and pulled away from the windshie ld.
When you dr ive faster than
4 mp h (6 km/
h), the w iper arms a utomat ica lly re turn to
t he par k position and could ca use pa int
d amage to the front lid!
Clear vi sion 61
@ Tips
- Yo u can also turn on t he service position,
for example, if yo u want to protect the
w indshield from icing by using a cover.
- Th e service posit io n moves to
off auto­
matically when you operate the wind­
shield wiper lever, or speed exceeds
4 mph (6 km/h).
Replacing front wiper blades
Wiper blades in good condition help keep the
windshield clear.
Fi g. 70 Unl atching w ipe r blade s
Fig. 71 Re mov ing w iper b lades
Removing the wiper blade
.. Move the wipers to the service pos it ion
c::> page 61.
.. Fold the windsh ie ld w iper arm away from
the glass .
N 0
i ,:. .., m
.. On the upper end of the wiper arm at the
corr uga tion, squeeze the p lastic ret ainer to­
gethe r on both s ides in the direction of the
arrow
c::> fig. 70.
.. Rotate the w iper b lade in the direction of
the arrow @
c::> fig. 71 away from the wiper
arm .
.. Lift the wiper b lade off in the d irection of
t he arrow @.

62 Clear vis ion
Install ing th e wiper blade
.,. Pla ce the rounded end of the wiper onto the
end of the w iper arm in the
op pos ite direc ­
tion to the arrow @
r=;, fig. 71.
.,. Squeeze the corrugation on the w iper until
you hear it click in the wiper arm .
.,. Fold the wiper arm back onto the wind­
shield .
.,. Switch the ign ition on and move the wiper
lever down briefly
r=;, page 59, fig . 69 . The
wipe r will move back to the park position.
_& WARNING
- Clean yo ur wiper blades regularly w it h a
windshield washer solution to prevent streaking. If the wipe r blades are very
dirty, for examp le with insects, carefu lly
clean the w iper blades with a sponge or a
soft brush.
- For your safety, you should replace the
wiper blades once or twice a year. See
your authorized Aud i dealer for replace­
ment blades.
(D Note
- The w iper blades may only be changed
r=;, page 61 in the service position! Other­
wise, you r isk damaging the paint on the
front lid o r the windsh ield wiper motor .
- To prevent damage to the wiper system:
-Always loose n blades which a re fro zen
t o the windshield before operating
w ipers.
- Do not use gasoline, kerosene, paint
t hinne r, or o ther solven ts on o r near
t he wipe r blades .
- Do not attemp t to move the wipers by
hand.
{D) Tips
The front wiper b lades are different
lengths; the blade o n the dr ive r's side is
longer .
Mirrors
Automatically dimming inside mirror
The automatic dimming function can be
turned on and off if required .
Fig . 72 Inside rearv iew mirror: auto d imming on/off
button and ind icator lig ht
Disabling auto d imming
.,. Press button ® r=;, fig. 72 -the green indica­
tor light @ goes out .
Activating /reactivating auto dimming
.,. Press button @¢ fig. 72 -the green indica-
tor light @ goes on .
Automatic dimming function
The automatic dimming function is act ivated
every time the ign it ion is turned on . T he g reen
indica tor light is lit to indicate auto d imming
is active.
When dimming is act ivated, the inside m irror
will darken
automatically i n response to the
amount of light st riking the mirro r (such as
headlig hts from rearward approaching vehi­
cles). Even in dimming mode, the mirror sur­
face turns bright when:
- t he in terior lig ht is swi tched on
- reverse gear is engaged.
Senso rs for automatic headlight s
With the help of the sensors in the mirror,
when the light switc h is in the
AUTO posit ion,
the low beams are switched on and off auto­ matically depending on the amb ient light con-
ditions. ..,.

_& WARNING
Broken glass of automatic dimming mirror
can cause electrolyte fluid leakage. Elec­
trolyte fluid can irritate sk in, eyes, and res­
piratory system .
- Repeated or prolonged exposure to elec­ trolyte can cause ir ritation to the resp ira­
tory system, espec ially among people
with asthma or other respiratory condi­
ti ons. Get fres h ai r i mmedia tely by leav­
ing the vehicle or, if that is not possible,
open windows and doors all the way.
- If electrolyte gets into the eyes, flush
them thoro ughly with large amounts of
clean water for at least 15 min utes;
med ica l attent ion is recommended.
- If e lectrolyte contacts sk in, f lush affect­
ed area with clean water for at least 15
minutes and then wash affected area
with soap and water; medical attention
is recommended . T horoughly wash af­
fected clothing and shoes before reuse .
- If swallowed and person is conscious,
rinse mouth w ith water for at least 15
min utes . Do not i nd uce vom it in g unless
inst ructed to do so by medical professio­
nal. Get medical atten tion immediately.
CD Note
liquid electro lyte leaked from a b roken
m irror glass will damage any p lastic surfa­
ces it comes in contact with. Clean up spil­
led electro lyte immediately wi th clear wa ­
t er and a sponge.
(D Tips
- If yo u switch off the automatic dim·
ming function on th e in sid e mirror , au ­
t o mati c dimming of the out sid e mirror s
w ill likewi se be di sabled .
-Check to make sure there are no objects
preventing light from reaching the inside
mirro r.
- Do no t attach any sticke rs to the wind ­
sh ield in front of t he two light sensors,
as this would interfere with both the au ­
tomatic operation of the headlights and
Clear vi sion 63
the a utomatic dimming of the inside
mirror(s) .
Outside mirrors
The outsid e mirrors ar e electrically adjusted .
Fig. 73 Forward sect io n of dr iv er's armrest: powe r mir ­
ro r control s
Adjusting the outside mirrors
.,. Turn the adjust ing knob to position © (driv­
er 's s ide) or in pos ition ® (passenger side)
r::!) fig. 73.
... Press the knob in the appropriate dire ction
to move the mi rror surface so that yo u have
a good view to the rear .
Heated mirrors
... Tu rn the knob to position @.
Folding both out side mirro rs flat*
.,. Turn the knob to @.
Depend ing on the outside temperature, the
mirror surfaces are heated until the ignition is
switched off - even if the knob is no longer in
pos ition @.
You are we ll-advised to fold* the outside mir­
rors in maneuvering in tight spaces or when
leaving the car parked close to other vehicles.
CD Note
- Curved (i .e. convex) mirror surfaces in­
crease yo ur field of view. Remember that
vehicles or other objects will appear smaller and farther away than when
seen in a flat m irror . If you use this mir­
ror to estimate distances of following ve-
hicles when chang ing lanes, you could ..,.

Parking system
Parking system
advanced
Introduction
Applies to vehicles: with pa rkin g system advanced
D D
Fig. 92 Park ing mode l: Reve rse parking
F ig . 93 Parking mode 2: Pa rallel parking
Vehicles w ith the park ing system are equ ipped
with a
rear view camer a in addition to the
acoust ic and visual park ing system .
You ca n choose between two modes to help
you when parking your vehicle . Use "parking
mode 1" when park ing in a parking space o r
ga rage
Q fig . 92. If you are goi ng to be paral­
l el par king, use "parking mode 2"
~ fig. 93.
Par king system 89
General Information
Applies to vehicles: wit h parking system advanced
Fig. 9 4 View from top: Rea rvi ew camera coverage area
---
---------
Fi g. 95 Side view: Rearv iew came ra coverage area
Sen sor s in the bumper
Sensors a re located in the front and rear
bumpers . If these detect an obstacle, a udible
and visual signals warn you. The range at
which the sensors begin to meas ure is approx­
i mately:
front s
ide 3 ft (0.90 m)
center 4 ft (1.20 m)
side 2 ft (0.60 m)
rear center 5.2 ft (1.60 m)
The closer you get to the obstacle, the shorter
the interva l between the audible signals . A
continuous tone sounds when the obstacle is
less than approximately 1 foot (0.30 meters)
away . Do not continue dr iving farther .
If the distance to an obstacle rema ins con­
stant, the volume of the distance warn ing
gradually drops after about fo ur seconds ( this
does not apply in the cont inuous tone range) .
II>

90 Parking system
Rear view camera coverage area
The rearview camera shows you the area be­hind your vehicle in the navigation system dis­
play. This area roughly corresponds to the
area in
¢ fig. 94 and (!) ¢fig. 95. Orientation
lines and colored surfaces are projected in the
area shown, which can help you with parking
and maneuvering. Objects that are located in
an area that is not captured by the camera@
¢ fig. 95 and that are closer to the bumper
will not appear on the navigation system dis­ play.
We recommend that you practice parking with
the rearview camera in a traffic-free location
or parking lot to become familiar with the sys­
tem, the orientation lines, and their function.
There should be sufficient light and good
weather conditions when doing so.
In the navigation system display, objects or
vehicles appear closer or further away if:
Objects or vehicles appear closer or farther
away in the navigation system if:
- you are driving in reverse gear from a level
surface onto an incline, or a downward
slope,
- you are driving in reverse gear toward pro-
truding objects.
The accuracy of the o rientation lines and blue
surfaces diminishes if:
- the rearview camera does not provide a reli­ able image, for example, in poor visibility
conditions or if the lens is dirty,
- the image on the screen is not visible due to
sun glare and reflection .
Caring for the rearview camera lens
The rearview camera is located in the center
of the vehicle above the rear license plate bracket. In order for the rearview camera to
function properly , the camera lens must be
kept clean and free of snow and ice .
- Dampen the lens with a household alcohol­
based glass cleaner , and clean the lens with
a dry cloth. - Remove
snow with a hand brush and ice
preferably with a de-icing spray
¢ (D .
A WARNING
--
-The parking system cannot replace the
driver's attention. The driver alone is re­
sponsible for parking and similar driving maneuvers .
- Sensors have blind spots in which objects
cannot be detected. Pay special attention
to small children and animals because
the sensors cannot always detect them .
- Always keep your eyes on the vehicle's
surroundings, using the rearview mirror
as well.
- Do not allow yourself to be distracted from traffic by the rearview camera pic­
tures in the navigation system display .
- If the position and the installation angle
of the camera has changed, for example,
after a rear end collision, do not continue
to use the system for safety reasons .
Have it checked by an authorized Audi
dealer or other qualified workshop.
(D Note
-Low obstacles already s ignaled by a
warning can disappear from the system's detection range as they are approached
and will not continue to be signaled. Ob­
jects such as barrier chains, trailer draw
bars, narrow painted vertical poles or
fences may not be detected by the sys­
tem, posing risk of damage.
- Never use warm or hot water to remove
snow or ice from the rearview camera
lens because the lens could crack.
- Never use products that are abrasive
when cleaning the lens.

Switching on and off
Applies to vehicles: with parking system advanced
Fig . 96 Section of the center console: Par k ass ist
switch
F ig. 97 Nav igatio n system dis p lay: visual distance d is ­
play
Switching on
.,. Switch the navigation system and the navi­
gation system disp lay on.
.,. Engage the reverse gear, or
.,. Press the
l""' I switc h in the center console
9 fig . 96. A short confirma tion tone so unds
and the indicato r light in the switch lights
up .
Sw itching between the rear v iew camera
and visual display
.,. Press the Graphic con trol button
9 page 9 2, fig . 98 to see the visua l dis­
play .
.,. Press the
Rear view contro l button to see
the rear view camera image
c) fig. 9 7.
Switching off
.,. Drive faster than 6 mph (10 km/h), o r
.,. Press the
l""' I switch, or
.,. Switch off the ignition .
Parking system 91
Segm ents in the visual display
The red segmen ts i n fro nt of and behind the
vehicle
c) fig . 97 he lp you to de termine the
distance between yo u and an obstacle. As
you r vehicle comes close r to t he obstacle, the
segments move closer to the vehicle . The col­
lision area has been reached when the next to
l ast segment is displayed. Do not continue
driv ing farther
c) .&. in General Information
on page
90!
A WARNING
- Th e nav igation system d isplay cannot
show, or c annot adequately show, cer­
tain o bjects (s uch as small posts o r gra­
ting), recesses in the groun d and pro­
trud ing parts on anothe r ca r.
- On ly use t he rearview came ra to assist
you if it shows a goo d, clear pict ure. For
examp le, the image may be affected by
the sun sh ining into the lens, d irt on the
lens or if there is a defect.
@ Tips
- The sensors m ust be kept clean and free
of s now and ice for the park assist to op­
erate .
- Yo u can change the vo lume and pitch of
the s ignals
c::> page 93 .
- What appea rs in the disp lay is time -de ­
layed.
-

94 Parking system
• Press the Settings control button.
- Front volum e -front sensor vol ume
- Front fr equenc y-front sensor frequency
-Rear volume -rear sensor volume
-Rear frequency -rear sensor frequency
-In-car entert ainment fader -when the park-
ing system is sw itched on, t he volume of the
active audio source is lowered .
The new ly adjusted value is briefly heard from
the signa l generator.
(D Tips
Changed settings are activated when park­
ing system is switched on aga in.
Error messages
Applies to vehicles: with parking system advanced
There is an error in the system if the LED on
the
IP.. ~ I sw itch is blinking and you hear a con­
tinuous alarm for a few seconds after switch­ ing on the parking system or when the park­
ing system is al ready act ivated. Have your au­
thor ized Audi dealer co rrect the e rror.
@ Tips
If an error has occurred before the ignition
is tu rned off, the LED in the~ switch will
blin k the next time the ignit ion is switched
on, reverse gear sele cted, and the a coustic
pa rking system is ac tiva ted .