2011 AUDI A3 window

Reactivating the system after battery
disconnection
Reactiva ting the convenience close/open feature
If the vehicle bat tery is disconnected and then reconnec ted,
t h e automatic closing and op ening f unctio n will not work
u ntil it is r eactiva ted. To reactivat e this feature, perform the
fo llowing ste ps:
Reactivating close /open feature
- Pull and hold the power window switch until the window is
com pletely closed.
- Release the switch .
- Pull the switch again for o ne second. The a utomatic
closing/opening is now reactivated .•
Panoramic sliding sunroof
A pp lies to vehicles : w ith panoramic sliding sunroof
Description
The pa no ram ic s lid ing sunroof is opera ted wi th t he toggle switc h
=> fig. 42 when the ignit ion in on.
T he panoramic sliding sun roof can sti ll be opened or closed for about
1 0 m in utes after the ig nition has been switched off. However , as
soon as the driver's or passenger 's door is opened, the sw itch for the
roof is inoperat ive. •
Con tro ls a nd e quip ­
m en t Vehicle
OP-eration
Opening and closing
Applies to vehicles : with pano ram ic sliding sunroof
Opening and closing panoramic sliding
sunroof
............... ...... ....................... .
;;;;;;;;;; ;;;;;::: ::::· ::;:;;::;;;;;;;;;; ;;;;i
1·············~1
.............. . ............. . ............. . .............. . ............ ..
• •
Fig. 42 Sectio n o f th e
roo f line r To gg le
s wit ch fo r the
p anora mic sli ding
s u nro of
Th e panoramic slid ing sunroof is opened in two stages. First,
the roof lifts up and t hen it can be opened .
Lifting
-Tap the switc h@ ~ fig. 42 b riefly, an d the roof lifts a uto-
matically (pop -u p position) .
Opening automatically (independent
operation)
-Tap t he switch (D ~ fig. 42 b riefly , and the roof moves to
t h e
lift position .
-Tap the switch (D briefly a second time , and the roof
moves to the
low wind noise comfort position .
- Press the switch (D until the roof is fully open. In this
position increased wind no ise may occur .
Vehicle care Do-it-yourselt service iTechnical data

Rear reading light
Press the switch "<~ to turn on and off the reading light .•
Luggage compartment light
A dome light in the rear roof liner illuminates the luggage
compartment. An additional light is provided on the
inside of the rear lid .
The light is located on the left side of the trunk .
With the switch at the center position, the rear dome light is auto­ matically switched on as soon as the rear lid is opened. The rear dome
light goes out 30 seconds after the rear lid is closed .
If the rear lid is left open for more than 10 minutes, both the rear
dome light and the light in rear lid are switched off to conserve the
battery charge. •
Vision
Applie s to veh icl es: w ith lig ht p ackag e or illum inated vanity mirror
Sun visors
Using the sun visors makes driving safer.
n,ISJ_
G
(
-
1
Fig. 59 Sun visor
Contro ls a nd e quip ­
m en t Vehicle
OP-eration
Clear vision
The sun visors for the driver and front passenger can be removed
from their center mountings and moved toward the door windows
(D
=> fig. 59 to protect against side glare .
The vanity mirror in the sun visors is covered by a lid. When you slide
the lid @open the mirror illumination comes on automatically.
When you slide the lid shut or fold the sun visor back up, the illumi­
nation also goes out.
There is a folding visor between the visors for the driver and the passenger which can be used to cover the space above the rear view
mirror .•
Mirrors
Manual anti-glare adjustment
Standard setting
- Move the small lever (located on the bottom edge of the
mirror) to the front.
Anti-glare setting
- Move the small lever (located on the bottom edge of the
mirror) to the rear. •
Vehicle care Do-it-yourselt service iTechnical data

Clear vision
Applies to veh icles : w ith automat ically dimm ing inside mirror
Automatically dimming inside mirror
The automatic dimming function can be turned on and
off if required .
Disabling auto dimming
Fig . 60 I nside rea r
v ie w mirror
- Press butt on @ ~ fig . 60 brie fly, -the green indic ator
light ® goes out.
Activating/reactivating auto dimming
- Press button @ briefly, -the green indicator ligh t® goes
on.
Automat ic dimming function
The automatic dimming function is activated every time the ignition
is turned on. The g ree n indicator light is lit to indica te auto d imming
is active.
W hen dimm ing is act ivated, the inside mir ror w ill darke n
automati­
cally
in response to the amou nt of light striking the mirror (such as
head lights from rearward approaching vehicles). Even in d imming
mode, the mirror surface turns br ight when:
• the interior light is switched on
• reverse gear is engaged.
& WARNING
Broken glass of automatic dimming mirror can cause electrolyte
fluid leakage . Electrolyte fluid can irritate skin , eyes, and respira­
tory system .
• Repeated or p rolonged expo sur e to electrolyte can cau se irrita­
tion to the resp iratory system, esp ecially among people with
asthma or other r espiratory conditions. Get fre sh air immediately
by le aving the vehicl e or, if that is not po ssible , open window s and
doors all the wa y.
• If ele ctrolyte gets into the eye s, flush them thoroughly with
large am ount s of clean water f or at lea st 15 minute s; medical
attention is re commended .
• If electrolyte contacts skin , flush affected area with clean
water for at l east 15 minutes and then wash aff ected area with
s oap and water; medical attention is rec ommended . Thoroughly
wash affected clothing and shoe s before reu se.
• If swallowed and person i s con sciou s, rinse mouth with water
for at least 15 minutes. Do not induce vomit ing unle ss instru cted
to do so by medical profe ssional. Get medical attenti on immedi­
ate ly .
0 Note
Liquid e lectrolyte leaked from a broken mir ror g lass will damage any
plastic surfaces it comes in contact with. Clean up spi lled electrolyte
immediately with clear wate r and a sponge.
[I) Tips
• Check to make su re t he re are no obje cts preventing light from
reac hing the inside mirror.
• Do not attach any st ick er s to the w indshield in front of the light
sensor, as this would interfere with the a utomatic operation of the
head lights and the a utomat ic dimming of the inside mir ror. •

Clear vision High wiper speed
- Move the lever up to posi tion ® ·
One-touch wiping
- Move the lever to position 0, when you want to wipe the
w indsh ie ld
briefly .
Automatic wiper/washer
-Pull t he lever to posi tion ® (t oward t he s tee ring w heel)
and hold.
- R elease t he lever . T he washer stops and the wipers keep
goi ng for about four seco nds .
Turning off the wipers
- Move the lever bac k to posi tion ®·
The w indshield wipe rs an d washer only wo rk when the igni tion is
tur ned on. If you switch off t he ig nition w ith the winds hield wiper
lever st ill in the inte rval wipe pos it ion and then come back a wh ile
later and drive off , the ra in sensor wi ll reactivate itself after the
vehicle speed has exceeded 4 mph (6 km/ h).
The r ain senso r* is only activated with the wipe r lever set to position
@ . When it starts to rain, the rain sensor will automatically act ivate
t he in term itte nt w ip ing mode .
To red uce the sensit iv ity of the sensor, move sw itch @dow n. To
increase the sensitivity, move the switch up. The higher you adjust the
sensitivity, the faster the sensor will react when it senses moistu re on
the windshield .
Th e rain senso r wipe r inte rvals dep end on the sensi tivi ty set ting a s
well as veh icle speed. During brief stops , wiper motion will ad just in
re lation to the amoun t of rain on the w indshield.
Automatic wiper/was her: To eliminate water droplets, the wind ­
shield wiper pe rforms one afterwipe operation after severa l secon ds w
hile driv ing. You can switch this funct ion off by moving the lever to
posi tion ® within 10 seco nds of the afterw ipe o per ation . T he afte r­
w ipe funct ion is reactivated the next time the ignition is switc h.
When the ignition is turned on, the washer jets are heated *.
& WARNING
• Wiper bl ades are crucial for safe driving! Only when they are in
good condition are they able to cl ear the windows properly to
pro vide uncompromised vi sibility. Worn or damaged wiper bl ade s
are a safety hazard=>
page 69, "Replacing front w iper blades"!
• The light/rain sensor* is only designed to assist and support
the driver. It remains entirely th e driver's responsibility to
monitor outs ide weather condit ions and to manually ac tivate the
wip ers as soon as rain or dr izzle reduces visibility through the
windshield.
• The windshield must not be treated with water-repellent
mater ial s. They can increase glare under poor visibility conditions
such as wetness, darkness, or when the sun is low on the horizon.
In addition , they can cause the windshield wipers to chatter.
0 Note
• In the case of frost, check whether the windshield wiper blades are
fro zen to the windsh ie ld. Switching on t he w indshield wipe rs can
damage the wiper blades!
• Do not use the wipers to clear a frosted w indow . Using the wipe rs
as a convenient ice scraper will destroy the wiper blades.
• Prior to us ing a car was h, the winds hield wiper system must be
sw itched off (lever in posit io n 0). This helps to prevent unintentional
switching on and demage to t he windshield woper sys tem. ..,.

(]] Tips
• The w indshield wipers are switched off when the ign ition is tu rned
off . Activate the windshield wipers after the ignition is switched back
on by mov ing the w indshield wipe r leve r to any pos ition.
• Worn or dirty windshield w iper blades cause smearing, which can
affect the operat io n of the l ight/rain sensor*. Check t he condi tion of
your windshield wiper b lades regularly.
• The rain sensor is part of the inte rval wiping system . Turning off
the ignition will also deactivate the rain sensor. To reactivate the
sensor, switch off the inte rval wiping funct ion, the n switch it back on
again .
• Applies to veh icles with light/ra in sensor: When the w ipers are
switched on manually and in rain conditions, the automatic head­
lights* turn on~
page 56, "Switching the headlights on and off ·f!: "
or off during the day when the wipers are no longer operating. The
au tomatic headlights* func tion is available in t his case only when the
light switch is in the "AUTO" position~
page 56, fig. 49.
• Make su re the washe r fl ui d reservoir in the eng ine compartment is
topped off before going on a long trip. Look up::::)
page 243 for
check ing and fill ing t he washer conta iner.
• The wipers only operate with the hood completely closed. •
Contro ls a nd e quip ­
m en t Vehicle
OP-eration
Clear vision
Rear window wiper cs;J
The wiper lever is also used to operate the rear windo w
w iper and the automatic wiper/ washer function .
Fig . 63 Wi per lev er:
a ct iva ting the rear
w indow wi per an d
w ashe r
The rear window w iper and t he au tomatic wiper/washer func­
tions are activated as follows:
Intermittent wiping
- P ush the wipe r lever forward towards the dashboard and
to the
first position ©~ fig. 63 . T he rear window wiper
w ill wipe the win dow approx. every four seco nds.
Automatic wiper/washer function
- Push the wiper lever forward to the second stop, position
0 , and ho ld it there for as long as you want the rear
wiper/washer to operate.
- Release the lever aga in. T he wiper w ill keep run ning for
app rox . four seco nds .
Switching intermittent wiper action off
- Pull the lever a ll the way back to the original posi tion.
Vehicle care Do-it-yourselt service iTechnical data

Clear vision
in. WARNING
Wiper blades are crucial for safe driving! Only in good condition are they able to clear the windows properly to provide unrestricted
visibility. Worn or frayed wiper blades are a safety hazard!
=> page 69, "Replacing front wiper blades"
(D Note
In freezing or near freezing conditions:
• Always check that the wiper blades are not frozen to the glass
before you turn the wiper on. Loosen a wiper blade which is frozen in
place before operating the wiper to prevent damage to the wiper
blade or the wiper motor.
• Do not use the wiper to clear a frosted window . Using the wipers
as a convenient ice scraper will destroy the wiper blades.
[I) Tips
For better rearward vision when parking, the rear window wiper is
automatically activated one time when the windshield wipers are
switched on and reverse gear is engaged. •
Service position
Replacing the windshield wiper blades is only possible when
you move the wiper arms into the service position. In order to
use the windshield wipers, the hood must be completely
closed. When there is a risk of frost, make sure that the wiper
blades are not frozen to the windshield.
- Switch the ignition on. - Switch the
ignition off again and move the wiper lever
=:> page 65, fig. 62 from position Oto 1 within
10 seconds. The wiper arms now move into the field of
view in the windshield.
The service position can also be selected in the driver information
system*=>
page 22 .
(D Note
Never drive your vehicle when the windshield wiper arms are in the
service position and pulled away from the windshield. When you drive
faster than 4 mph (6 km/h) , the wiper arms automatically return
back to the park position and could cause paint damage to the engine
hood!
[I) Tips
• You can also turn on the service position, for example, if you want
to protect the windshield from icing by using a cover.
• The service position moves to
off automatically when you operate
the windshield wiper lever, or speed exceeds 4 mph (6 km/h). •

Clear vision
& WARNING (continued)
for example with insects, carefully clean the wiper blades with a
sponge or a soft brush.
• For your safety, you should replace the wiper blades once or
twice a year. See your authorized Audi dealer for replacement
blades.
0 Note
• The wiper blades may only be changed=> page 68 in the service
position! Otherwise, you risk damaging the paint on the hood or the
windshield wiper motor.
• You should not move your veh icle or press the windshield wiper
lever when the wiper arms are folded away from the windshield. The
windshield wipers wou ld move back into their original position and
could demage the hood and windshield.
• To help prevent damage to the wiper system, always loosen
blades which are frozen to the windshield before operating wipers.
• To help prevent damage to w iper blades, do not use gasoline,
kerosene, paint thinner, or other solvents on or near the wiper
blades.
• To help prevent damage to the wiper arms or other components,
do not attempt to move the wipers by hand .
(I) Tips
• Commercial hot waxes applied by automatic car washes affect the
cleanability of the glass surface.
• You can also use the service position, for example, if you want to
protect the windshield from icing by using a cover.
• You cannot act ivate the service position when the hood is open.
• Th e front wiper blades are different lengths; the blade on the
driver's side is longer.•
Changing the rear wiper blade
Removing the wiper blade
Fig. 66 Installing/re
moving wiper blade
- Fold the windshield wiper arm away from the glass.
- Pull the metal surround of the wiper blade out of the
retainer in the direction of the arrow =:> fig. 66. Hold the
wiper arm firmly by the upper end as you do this.
Attaching the wiper blade
-Adjust the position of the wiper blade in the retainer
~ fig. 66 (see close up).
- Press the wiper blade into the retainer. Hold the wiper arm
firmly by the upper end as you do this.
- Fold the wiper arm back onto the glass.
& WARNING
• To avoid streaks, you should clean the windshield wiper blades
regularly with window cleaner. For heavy soiling, for example,
insects, the wiper blades can also be cleaned with a sponge or a
cloth.
~

Seats and storage
General recommendations
Why is your seat adjustment so important?
The safety belts and the airbag system can only provide
maximum protection if the front seats are correctly
adju sted.
Th ere are several dif ferent ways you can ad just the d river's sea t and
t he front passenger's seat so that it confo rms to your body size .
It is
especially important t hat the seat be adjusted properly so that:
• you can easily and quickly reach a ll the switc hes and contro ls in the
ins trumen t pa nel
• your body is properly supported thus reducing phys ica l stress and
fatigue
• the safety be lts and airbag system can offer maximum protection
=>
page 145
In the follow ing chapters, you will see exactly how you can best adjust
your sea ts .
Th ere are special regulations a nd instr uctions for install ing a child
safety seat on the front passenger 's seat. Always heed the informa ­
tion regarding child safety p rovided in=>
page 167, "Child Safety ".
& WARNING
Incorrect seating posit ion of the driver and all other passengers
can result in seriou s personal injury.
• Always keep your feet on the floor when the vehicle is in
motion -never put your feet on top of the instrument panel, out
of the window or on top of the seat cushion! This applies especially
to the passengers. If your seating po sition is incorrect you
increase the ri sk of injury in the case of sudden braking or an acci-
Controls and equip ­
ment Safety first
Seats and storage
& WARNING
(con tinu ed)
dent . If the airbag inflates and the seating position is incorrect
this could result in per sonal injury or even death .
• It is important for both the dri ver and front passenger to keep
a distance of at least 10 inches (25 cm) between themselves and
the steer ing whee l and /or instrument panel. If you're sitting any
closer than this , the airbag system cannot protect you properly. In
addition to thi s, the front seats and head restraints must be
adjusted to your body height so that they can give you maximum
protection .
• Always try to keep as much distance as possible between your­
self and the steering wheel or instrument panel.
• Do not adjust the driver's or front passenger 's seat while the
vehicle is moving. Your seat may move unexpectedly, causing
sudden loss of vehicle control and personal injury . If you adjust
your seat while the vehicle is moving, you are out of position. •
Driver's seat
The correc t sea t posi tion is import an t f or sa fe and
rel axed dri ving.
We recomm end that you a djust th e d rive r's sea t in the
fo llowing man ner:
- Ad just the sea t in f ore and a ft dire ct io n so that y ou can
e asily pus h the pe dals to the floor while keep in g you r
kne es slightly bent=>
& in "W hy is yo ur seat a djust m en t
so imp ort an t?".
- Adj ust the sea tbac k so tha t when yo u sit wi th y our back
agai nst the se atba ck, you can sti ll gra sp th e to p of t he
s te er ing w hee l. _..
Vehicle care Technical data