2011 Acura TL display

ÛÝÛÝ
If you sometimes f ind that the
temperature reading is a f ew
degrees above or below the actual
temperature, you can adjust it by
f ollowing these instructions:
You can choose this item to
customize f rom ‘‘METER SETUP’’
by pressing the INFO ( / ) button
repeatedly.
Press the SEL/RESET button to
enter the setting.
When your selection is successf ully
completed, the display changes as
shown above, and then goes back to
the customize item screen.
If the ‘‘SETTING INCOMPLETE’’
message appears, go back to
‘‘LANGUAGE SELECTION’’ and
repeat the procedure again.
The displayed number is the current
adjustment above or below the
outside temperature.
Adjust the outside temperature value
by pressing the INFO ( / ) button
repeatedly. Press the SEL/RESET
button to set the desired value.
Adjust Outside Temp. Display
CONT INUED
Multi-Inf ormation Display
Inst rument s and Cont rols
101
Canadian models
U.S. models
10/07/29 11:52:49 31TK4620_106
2011 TL

ÛÝ
µ
µ
µ
Î
Î
When your selection is successf ully
completed, the display changes as
shown above, and then goes back to
the customize item screen.
If the ‘‘SETTING INCOMPLETE’’
message appears, go back to
‘‘ADJUST OUTSIDE TEMP.
DISPLAY’’ and repeat the
procedure again. You can select the reset timing of
the Trip A information: Trip A,
Average Fuel Economy A,
Average Vehicle Speed A, and
Elapsed Time A.
You can choose this item to
customize f rom ‘‘METER SETUP’’
by pressing the INFO ( / ) button
repeatedly. WITH REFUEL The Trip A
inf ormation is reset every time you
ref uel your vehicle.
MANUAL ONLY You can reset
the Trip A inf ormation when Trip A
is displayed (see page ). There are three reset choices you
can make:
IGN OFF The Trip A information
is reset when you turn the ignition
switch to the LOCK (0) position. Models equipped with the
keyless access system have an
engine start/stop button instead
of an ignition switch. VEHICLE
OFF (LOCK) Mode is the
equivalent of LOCK (0). For
more inf ormation, see pagesand . 81
:
178 181
Trip Computer Trip A Inf o Reset
Multi-Inf ormation Display
102
U.S. models Canadian models
10/07/29 11:52:59 31TK4620_107
2011 TL

ÛÝ
Press the SEL/RESET button to see
the selections.
Select the desired setting by
pressing the INFO ( / ) button,
then enter your selection by pressing
the SEL/RESET button. When your selection is successf ully
completed, the display changes as
shown above, and then goes back to
the customize item screen.
If the ‘‘SETTING INCOMPLETE’’
message appears, go back to ‘‘TRIP
COMPUTER TRIP A INFO RESET’’
and repeat the procedure again.
CONT INUED
Multi-Inf ormation Display
Inst rument s and Cont rols
103
10/07/29 11:53:06 31TK4620_108
2011 TL

ÛÝÛÝ
Adjust Alarm Volume
Select the warning alarm volume
f rom three levels.
You can choose this item to
customize f rom ‘‘METER SETUP’’
by pressing the INFO ( / ) button
repeatedly. Press the SEL/RESET button to see
the selections.
Select the desired level by pressing
the INFO ( / ) button, then enter
your selection by pressing the SEL/
RESET button.
When your selection is successf ully
completed, the display changes as
shown above, and then goes back to
the customize item screen.
If the ‘‘SETTING INCOMPLETE’’
message appears, go back to
‘‘ADJUST ALARM VOLUME’’ and
repeat the procedure again.
Multi-Inf ormation Display
104
10/07/29 11:53:13 31TK4620_109
2011 TL

ÛÝÛÝ
Auto Interior Illumination
While the headlight switch is turned
on, the interior lights gradually dim,
as the outside light level gets low.
You can customize at which outside
light level the lights start to dim.
ThereareMAX,HIGH,MID,LOW
and MIN levels and OFF for the auto
interior illumination settings.
If you want the illuminations to start
dimming as early as possible, select
MAX. For illuminations to start
dimming as late as possible, select
MIN. Choose HIGH, MID, or LOW
f or levels in between.
To disable the auto interior
illumination f unction, select OFF. You can choose this item to
customize f rom ‘‘METER SETUP’’
by pressing the INFO ( / ) button
repeatedly.
Press the SEL/RESET button to see
the selections.
Select the desired setting by
pressing the INFO ( / ) button,
then enter your selection by pressing
the SEL/RESET button.
CONT INUED
Multi-Inf ormation Display
Inst rument s and Cont rols
105
10/07/29 11:53:22 31TK4620_110
2011 TL

ÛÝ
When your selection is successf ully
completed, the display changes as
shown above, and then goes back to
the customize item screen.
If the ‘‘SETTING INCOMPLETE’’
message appears, go back to ‘‘AUTO
INTERIOR ILLUMINATION’’ and
repeat the procedure again. When this item is set to ON, you will
see some guidance messages on the
multi-inf ormation display. You can
change this setting between on and
of f . For more inf ormation on start
guidance messages, see page .
You can choose this item to
customize f rom ‘‘METER SETUP’’
by pressing the INFO ( / ) button
repeatedly.
182
Keyless Start Guidance Screens
On models with keyless access system
Multi-Inf ormation Display
106
10/07/29 11:53:28 31TK4620_111
2011 TL

ÛÝ
Select ON or OFF by pressing the
INFO ( / ) button, then enter
your selection by pressing the SEL/
RESET button. Press the SEL/RESET button to see
the selections. When your selection is successf ully
completed, the display changes as
shown above, and then goes back to
the customize item screen.
If the ‘‘SETTING INCOMPLETE’’
message appears, go back to
‘‘KEYLESS START GUIDANCE
SCREENS’’ and repeat the
procedure again.
Multi-Inf ormation Display
Inst rument s and Cont rols
107
10/07/29 11:53:34 31TK4620_112
2011 TL

ÛÝ
ÛÝ
ÛÝ
You can customize the MEMORY
POSITION LINK setting in
position setup.
While ‘‘POSITION SETUP’’ is shown,
press the SEL/RESET button to
enter the customize mode.
Each time you press the INFO( / )
button, the screen changes
as shown in the illustration. Press
the INFO ( / ) button until
you see the custom setting then
press the SEL/RESET button to
enter your selection.
Position Setup
Multi-Inf ormation Display
108
: Press the SEL/RESET button.
: Press the INFO button ( / ). Seepage109
.
10/07/29 11:53:40 31TK4620_113
2011 TL