2011 Acura TL display

ÛÝ
ÛÝ
Memory Position Link
On models with keyless access system
When Memory Position Link is set
to ON, the driver’s seat and the
outside mirrors move to the
positions stored in memory. To
cause the memory to activate, open
the driver’s door with the remote
transmitter. On models with keyless
access system, open the driver’s
door with the remote, or grab the
door handle while carrying the
remote.
To set the memory positions, see
page .
For inf ormation on using the remote,
see page . You can choose this item to
customize f rom ‘‘POSITION
SETUP’’ by pressing the INFO
( / ) button repeatedly. Press the SEL/RESET button to see
the selections.
Select ON or OFF by pressing the
INFO ( / ) button, then enter
your selection by pressing the SEL/
RESET button.
164
167
CONT INUED
Multi-Inf ormation Display
Inst rument s and Cont rols
109
10/07/29 11:53:48 31TK4620_114
2011 TL

When your selection is successf ully
completed, the display changes as
shown above, and then goes back to
the customize item screen.
If the ‘‘SETTING INCOMPLETE’’
message appears, go back to
‘‘MEMORY POSITION LINK’’ and
repeat the procedure again.
Multi-Inf ormation Display
110
10/07/29 11:53:53 31TK4620_115
2011 TL

ÛÝ
then press the SEL/RESET button
to enter your selection. While ‘‘KEYLESS ACCESS SETUP’’
is shown, press the SEL/RESET
button to enter the customize mode.KEYLESS ACCESS BEEP KEYLESS ACCESS
LIGHT FLASH DOOR UNLOCK MODE
There are three custom settings for
the keyless access setup:
CONT INUED
On models with keyless access system
K eyless A ccess Setup
Multi-Inf ormation Display
Inst rument s and Cont rols
111
: Press the INFO button ( / ).
: Press the SEL/RESET button. Seepage112
.
Seepage113 .
Seepage114 .
10/07/29 11:54:01 31TK4620_116
Û
Ý
ÛÝ
Each time you press the INFO
( / )
button, the screen chan ges
as shown in the illustration. Pres s
the INFO ( / ) button until you
see the setting you want to customize,
2011 TL

ÛÝ Û
Ý
Press the SEL/RESET button to see
the selections.
When your selection is successf ully
completed, the display changes as
shown above, and then goes back to
the customize item screen.
To select whether the driver’s door
or all doors unlock when you open
the driver’s door with the remote or
by grabbing the door handle (while
carrying the remote), f ollow these
instructions:
You can choose this item to
customize f rom ‘‘KEYLESS ACCESS
SETUP’’ by pressing the INFO
( / ) button repeatedly. Select DRIVER DOOR or ALL
DOORS by pressing the INFO
( / ) button, then enter your
selection by pressing the
SEL/RESET button . If the ‘‘SETTING INCOMPLETE’’
message appears, go back to ‘‘DOOR
UNLOCK MODE’’ and repeat the
procedure again.
Door Unlock Mode
Multi-Inf ormation Display
112
10/07/29 11:54:09 31TK4620_117
2011 TL

ÛÝ
Û
Ý Press the SEL/RESET button to see
the selections.
Select ON or OFF by pressing the
INFO ( / ) button, then enter
your selection by pressing the
When KEYLESS ACCESS LIGHT
FLASH is set to ON, some
exterior lights blink twice
when you unlock the doors by
grabbing the driver’s door handle
while carrying the remote.
You can choose this item to
customize f rom ‘‘KEYLESS ACCESS
SETUP’’ by pressing the INFO
( / ) button repeatedly.
The same exterior lights blink once
when you lock the doors by pushing
the door lock button while carrying
the remote.
Keyless Access Light Flash
CONT INUED
Multi-Inf ormation Display
Inst rument s and Cont rols
113
10/07/29 11:54:16 31TK4620_118
SEL/RESET button.
2011 TL

ÛÝ
When your selection is successf ully
completed, the display changes as
shown above, and then goes back to
the customize item screen. When KEYLESS ACCESS BEEP is
set to ON, the beeper sounds twice
when you unlock the doors by
grabbing the drivers door handle
while carrying the remote.
If the ‘‘SETTING INCOMPLETE’’
message appears, go back to
‘‘KEYLESS ACCESS LIGHT
FLASH’’ and repeat the procedure
again. You can choose this item to
customize f rom ‘‘KEYLESS ACCESS
SETUP’’ by pressing the INFO
( / ) button repeatedly.
When you lock the doors by pushing
the door lock button while carrying
the remote, the beeper sounds once.
Keyless Access Beep
Multi-Inf ormation Display
114
10/07/29 11:54:23 31TK4620_119
2011 TL

ÛÝ
Press the SEL/RESET button to see
the selections.
When your selection is successf ully
completed, the display changes as
shown above, and then goes back to
the customize item screen.
Select ON or OFF by pressing the
INFO ( / ) button, then enter
your selection by pressing the SEL/
RESET button. If the ‘‘SETTING INCOMPLETE’’
message appears, go back to
‘‘KEYLESS ACCESS BEEP’’ and
repeat the procedure again.
Multi-Inf ormation Display
Inst rument s and Cont rols
115
10/07/29 11:54:29 31TK4620_120
2011 TL

ÛÝ
INTERIOR LIGHT
DIMMING TIME
HEADLIGHT AUTO OFF TIMER
While ‘‘LIGHTING SETUP’’ is
shown, press the SEL/RESET
button to enter the customize mode. Here are the three custom settings
f or the lighting setup:
AUTO LIGHT SENSITIVITY
Lighting Setup
Multi-Inf ormation Display
116
: Press the SEL/RESET button. : Press the INFO button ( / ). See page
117.
See page 118.
See page 119.
10/07/29 11:54:37 31TK4620_121
then press the SEL/RESET button
to enter your selection.Û
Ý
ÛÝ
Each time you press the INFO
( / )
button, the screen chan g
as shown in the illustration. Pres s
the INFO ( / ) button until you
see the setting you want to customize, es
2011 TL