2011.5 Citroen C5 RHD wheel
[x] Cancel search: wheelPage 141 of 340
IX
139
DRIVING
6-SPEED ELECTRONIC
GEARBOX SYSTEM
)
automatic mode: gear lever in
position A
,
)
sequential mode: gear lever in
position M
,
)
SPORT
mode: gear lever in po-
sition A
and a press on button 1
.
Six-speed electronic gearbox system
which offers a choice between the
comfort of fully automatic operation or
the pleasure of manual gear changing.
There are two driving modes:
- automatic
operation for elec-
tronic control of the gears by the
gearbox,
- manual
operation for sequential
gear changing by the driver,
In automated mode, it remains possi-
ble to change gear manually by using
the steering mounted control paddles,
when overtaking, for example.
A SPORT
programme is available in
automated mode, providing a more
dynamic driving style.
Mode selection
The steering mounted paddles
cannot be used to select neutral
or to engage or disengage reverse
gear.
+.
Change up paddle to the right of
the steering wheel.
)
Press the back of the "+"
steering
mounted paddle to change up a
gear.
-.
Change down paddle to the left of
the steering wheel.
)
Press the back of the "-"
steering
mounted paddle to change down
a gear.
Steering mounted control paddles
Page 149 of 340
IX
!
147
DRIVING
Never select positions P
or R
if the vehicle is not stationary.
If, while the vehicle is moving, po-
sition N
is engaged inadvertently,
allow the engine to idle before en-
gaging position D
or M
.
Moving off
)
To start the engine, the gear lever
must be in position P
or N
.
)
Operate the starter.
)
When the engine is running,
place the gear lever on R
, D
or M as required.
)
Check, in the instrument panel,
the position engaged.
)
Release the brake pedal and ac-
celerate.
)
To avoid a possible difference
between the position of the gear
lever and the actual position of
the gearbox, always exit from
position P
with the ignition on
and brake pedal applied.
Otherwise, when the ignition is on or
the engine is running:
)
reposition the gear lever in posi-
tion P
,
)
put your foot on the brake pedal
and then select the gear you want.
Park
This position of the gear le-
ver is used to prevent the
vehicle from moving when
you are stationary.
)
To select position P,
move the
gear lever back to the highest
position (towards R
), then push
it forwards and then to the left.
)
To exit position P
, move the gear
lever to the right and then to the
position you want.
)
Only engage this position when
the vehicle is completely sta-
tionary. In this position, the front
wheels are locked. Make sure
that the gear lever is correctly
positioned.
Reverse gear
Only engage this position
when the vehicle is station-
ary. To prevent snatching,
do not accelerate too soon
after selection.
Neutral
Never select position N
if
the vehicle is moving.
Page 152 of 340
IX
150
DRIVING
FIXED CENTRED CONTROLS STEERING WHEEL
1
Rotation
-
Scroll the various pages of information on the instrument panel screen.
- Move through the various menus on the instrument panel screen.
- Increase/decrease values.
Short press
-
Open the menu on the instrument panel screen (only when stationary).
- Select and confi rm information.
Long press Trip computer zero reset (if the trip computer page is displayed).
2
Short press
- Cancel the current operation.
-
Return to the previous screen on the instrument panel screen.
Long press Return to the initial page on the instrument panel screen.
3
Short press Increase the speed in steps of 1 mph (1 km/h)/storing the speed.
Maintained press Increase the speed in steps of 5 mph (5 km/h).
4
Short press
Decrease the speed in steps of 1 mph (1 km/h)/storing the speed.
Maintained press Decrease the speed in steps of 5 mph (5 km/h).
5
Short press Suspend or resume cruise control/speed limiter (depending
on the mode selected).
6
Short press Select cruise control or speed limiter mode (the cycle on this
button will always begin with selection of the speed limiter).
7
Short press Deactivate cruise control/speed limiter.
8
Short press
- Pick up an incoming call.
- Hang up the current call.
- Open the telephone short-cut menu.
- Confi rm on the list and the telephone menu.
Long press Refuse an incoming call.
9
Short press/Long press Horn.
10
Short press Activate/deactivate Black Panel mode (night driving).
11
Short press Activate the voice command.
Long press Navigation instruction repeat.
Page 154 of 340
IX
152
DRIVING
SPEED LIMITER
System which prevents the vehi-
cle from exceeding the speed pro-
grammed by the driver.
When the limit speed is reached, the
accelerator pedal no longer has any
effect.
The speed limiter is switched on
manually: a speed of at least 20 mph
(approx. 30 km/h) must be pro-
grammed.
The speed limiter can in no way re-
place respect for speed limits or vigi-
lance and responsibility on the part
of the driver.
Steering mounted controls
The speed limiter switches are lo-
cated on the left-hand side of the
steering wheel.
Displays in the instrument panel
The speed limiter information is dis-
played in zone A
of the instrument
panel.
Programming
)
Press on button 4
to select speed
limiter mode " LIMIT
".
The selection is confi rmed by the
display of the function in zone A
of
the instrument panel.
Activation
)
Press on button 3
when the de-
sired maximum speed is dis-
played.
The information "ON"
then appears
in zone A
.
When the function is selected, the
last memorised speed and the infor-
mation "PAUSE"
are displayed.
With the engine running, you can ad-
just the memorised maximum speed,
displayed in zone A
, by pressing on:
)
Button 1
to increase the memo-
rised maximum speed.
)
Button 2
to decrease the memo-
rised maximum speed. Successive presses will modify the
maximum speed in steps of 1 mph
and a continuous press in steps of
5 mph.
Page 156 of 340
IX
154
DRIVING
CRUISE CONTROL
System which automatically main-
tains the vehicle speed programmed
by the driver, without any action on
the accelerator pedal.
The cruise control is switched on
manually: the vehicle speed must be
at least 25 mph (40 km/h) and you
must be in at least:
- 4th gear for manual gearboxes,
- 2nd gear for automatic gearboxes.
Displays in the instrument
panel
The programmed information is
grouped together in zone A
of the
instrument panel.
Programming
)
Press button 4
to select cruise
control mode " CRUISE
".
Steering mounted controls
The cruise control switches are lo-
cated on the left-hand side of the
steering wheel. The selection is confi rmed by the
display of the function in zone A
of
the instrument panel.
When the function is selected, no
cruising speed has yet been
memorised.
Once the desired speed has been
reached using the accelerator, press
button 1
or button 2
. The cruising
speed is then memorised and cruise
control is activated. The cruising
speed is displayed in zone A
of the
instrument panel, and "ON"
is dis-
played.
Adjustment of the memorised
speed while cruise control is
in operation
You can adjust the memorised speed,
displayed in zone A
, by pressing:
- Button 1
to increase the speed.
- Button 2
to reduce the speed.
Successive presses will modify the
cruise speed in steps of 1 mph and a
continuous press in steps of 5 mph. You can then release the accelera-
tor pedal. The vehicle will automati-
cally keep to the speed chosen.
The vehicle speed may vary slightly
from that memorised.
If during cruise control the system
cannot keep to the cruise speed
(e.g. on a steep descent), then the
speed fl ashes. If necessary, brake to
curb your speed.
Page 163 of 340
IX
161
DRIVING
Vehicle positions
High position
Changing a wheel (not possible if
speed > 6mph (10km/h)).
Mid-high position
For increased ground clearance (not
possible if speed > 25 mph (40 km/h)).
For use on diffi cult roads when trav-
elling at reduced speed, as well as
on car park ramps.
Position changes may only be
made when the engine is running.
The adjustable ground clearance
meets all types of situation. Apart
from a few specifi c situations, the
vehicle should be in the Normal
position.
)
Press once on one of the adjust-
ment controls.
The change in position is indicated
by a message on the instrument
panel screen.
Normal position
If the speed authorised for a particu-
lar position is exceeded, the vehicle
reverts automatically to the normal
position.
Low position
To facilitate loading or unloading the
vehicle.
For workshop inspections.
Not to be used in normal driving (not
possible if speed > 6mph (10km/h)).
Page 178 of 340
XI
176
PRACTICAL INFORMATION
TEMPORARY PUNCTURE
REPAIR KIT
Using the kit
The kit is located in the boot under
the fl oor.
)
Switch off the ignition.
)
Affi x the speed limitation sticker
to the vehicle's steering wheel
to remind you that a wheel is in
temporary use.
)
Check that the switch A
is in
position "0"
.
)
Connect the pipe of the car-
tridge 1
to the valve of the tyre to
be repaired.
)
Connect the compressor's elec-
tric plug to the vehicle's 12 V
socket.
)
Start the vehicle and leave the
engine running. Complete system consisting of a
compressor and a sealant cartridge
which permits the temporary repair
of the tyre so that you can drive to
the nearest garage.
This repair kit is available from
CITROËN dealers or a qualifi ed
workshop.
It is designed to repair holes of a
maximum diameter of 6 mm, locat-
ed exclusively on the tyre tread or
shoulder. Avoid removing any for-
eign bodies which have penetrated
the tyre.
Page 179 of 340
XI
!
177
PRACTICAL INFORMATION
)
Remove the compressor and un-
clip and store the cartridge in a
sealed bag to avoid staining your
vehicle with traces of fl uid.
)
Drive immediately for approxi-
mately two miles (three kilome-
tres), at reduced speed (between
15 and 35 mph [20 and 60 km/h]),
to plug the puncture.
)
Stop to check the repair and the
pressure.
)
Connect the compressor pipe di-
rectly to the valve of the repaired
wheel.
)
Switch on the compressor by mov-
ing the switch A
to position "1"
until the tyre pressure reaches
2.0 bars. If this pressure has not been
reached after approximately
fi ve to ten minutes, the tyre
cannot be repaired; contact a
CITROËN dealer to have your ve-
hicle repaired.