2010 SKODA FABIA language

Instruments and warning lights
22Warning against excessive speeds*This function enables you to set a speed limit, e.g. if you drive in town. A text in the display is intended to draw your attention
to the fact that you have exceeded the set
speed limit.Warning against excessive speeds– Select the menu point
Speed warning --- km/h.
.
– Drive e.°g at a speed of 50 km/h.– Press button
fig. 20
. Speed warning 50 km/h
is displayed in the informa-
tion display*. You can increase or reduce
this value with the aid of the button .
– After repeated pressing of the button , the value is stored.After pressing again, the value is erased and
--- is shown in the information display*.
You can set the desired speed in steps of 5 km/h by pressing the button , even when the vehicle is stationary. Confirm the
set speed by pressing the button .
If you now exceed the set speed limit,
Speed 50 km/h exceeded
will be shown on the
display. This text is shown until you lower the speed below the set limit or you switch off the displayed text with the button
fig. 20
.
An audible signal sounds as an additional warning signal.The set speed limit remains stored even after switching off the ignition.
MAXI DOT display (information display)*IntroductionThe information display provides you with information in a convenient way concerning the
current operating state of your vehicle
. The information system also
provides you with data (depending on the equipment installed in the vehicle) relating to the radio, mobile phone,
multi-functional indicator, navigation system, the unit
connected to the MDI input and the automatic gearbox. Certain functions and operatin
g conditions are always being checked on the vehicle
when the ignition is switched on and also while driving. Functional faults, if required repair work
and other information are indicated by red
symbols
page 24 and yellow symbols
page 24.
Lighting up of certain symbols is comb
ined with an acoustic warning signal.
Information and text
s giving warnings
are also shown in the display
page 26.
The display of text is possible in the following languages:
Czech, English, German, French, Italian,
Spanish, Portuguese, Russian and Chinese.
You can select the desired language in the setting menu.The following information can be shown in
the display (depending on the equipment
installed on the vehicle):
Fig. 20 Multi-functional indicator: Control elements
AB
AA
AB
AAAB
AB
Main menu
 page 23
Door, luggage compartment door and bonnet ajar warn- ing
 page 23
Service Interval Display
page 17
Selector lever position for an automatic gearbox
page 99
s3j8.a.book Page 22 Tuesday, April 20, 2010 1:10 PM

Instruments and warning lights
24Shown in the menu
Vehicle status
, if there is at least one error message. After selecting
this menu the first of the error messages is displayed. Several error messages are shown on the display under the message e.g.
1/3
. This indicates that the first of a total
of three error messages is displayed. The respective messages are displayed one after the other in an interval of 5 seconds. Chec
k as soon as possible the displayed error
messages. As long as the operational faults are not
rectified, the symbols are always indicated
again. After the first display, the symbol
s are indicated without information for the
driver. If a fault occurs, a warning signal will also
sound in addition to the symbol and text in
the display:
Priority 1 - three warning signals

Priority 2 - one warning signal
Red symbols A red symbol signals danger.– Bring the vehicle to a stop. – Switch the engine off.– Investigate the function indicated.– Obtain professional assistance. Meaning of the red symbols: Three
successive warning signals will sound if a red symbol appears.
Yellow symbols A yellow symbol signals a warning.Check the relevant function as soon as possible. The meaning of the yellow symbols: One
warning signal will sound if a yellow symbol appears.
If several operational faults of priority 2
exist, the symbols appear one after the other
and are each illuminated for about 5 seconds.SetupYou can change certain settings by means
of the information display. The current
setting is shown on the information display
in the respective menu at the top below the
line. You can select the following information (d
epending on the equipment installed on
the vehicle):
Language

MFD Data (MFA DATA)

Time

Winter tyres

Units

Alt. speed dis.

Service Interval (Service)

Factory Setting

Back
After selecting the menu point
Back
you will reach one level higher in the menu.

Engine oil pressure too low
page 29

Overheated clutches of the automatic gear- box DSG*
 page 98

Check engine oil level, engine oil sensor faulty
 page 29
s3j8.a.book Page 24 Tuesday, April 20, 2010 1:10 PM

Instruments and warning lights
25
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
Language Here you can set in which language the
warning and information texts should be
displayed. Displays of the MFA Here you can switch off or on certain di
splays of the multi-
functional indicator.
Time Here you can set the time, the time format (12 or 24 hour indicator) and the time change summer/winter time. Winter tyres Here you can set at which speed a warning si
gnal should sound. This function is used
for e.g winter tyres with the permissibl
e maximum speed less than the maximum
speed of the vehicle. When exceeding the speed, the following is
displayed on the information display*:
Winter tyres max. speed ... km/h (Winter tyres maximum ... km/h)
Measures Here you can set the units for temperat
ure, consumption and distance driven.
Second speed Here you can switch on the display of
the second speed in mph or in km/h
2).
Service Here you can have the kilometers still to
be driven and the days until the following
service interval shown and the Service Interval Display reset. Factory Setting After selecting the menu point
Factory Setting
the factory setting of the information
display is established again.2)Valid for countries where the values are indicated in British measuring units.
s3j8.a.book Page 25 Tuesday, April 20, 2010 1:10 PM

Communication
109
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
The buttons operate the functions for the operating mode of the current telephone.Operate the telephone via the information display*The display of texts in the menu
Phone
is possible in the following languages:
Czech, English, German, French, Italia
n, Spanish, Russian and Portuguese.
In the menu
Phone
you can select the following menu points:

Phone book

Dial number

Call register

Voice mailbox

Bluetooth

Settings

Back
Phone book In the menu point
Phone book
is the list of the loaded contacts from the telephone
memory and the SIM card of the mobile phone. In the phone phonebook there are 2 500 free memory locations available. Dial number In the menu point
Dial number
, you can write any telephone number. Select in
sequence the desired digits with the aid of
the handwheel and confirm it by pressing
the handwheel. You can select the numbers
0 - 9
, the symbols
+, , # and the func-
tions
Delete, Call, Cancel
.
Call register In the menu point
Call register
, you can select the following menu points:

Missed calls

Received calls

Last calls
Voice mailbox In the menu
Voice mailbox
, it is possible to set the number of the voice mailbox and
then dial the number. Bluetooth In the menu
Bluetooth
you can select the following menu points:

User
- the overview of the stored users

New user
- Search for new telephones which are in the reception range

Visibility
- Switching on the visibility of
the telephone unit for other devices

Media player
Active device

Paired devices

Search

Phone name
- the possibility to change the name of the telephone unit (pre-set
SKODA UHV) Settings In the menu
Settings
you can select the following menu points:

Phone book
Update

List
Surname

First name

Ring tone
Back Return in the basic menu of the telephone.
Note
The readout of the menu
Phone
and the voice control are no
t possible in the Chinese
language.
s3j8.a.book Page 109 Tuesday, April 20, 2010 1:10 PM

Communication
110
Voice controlDialogueThe period, in which the telephone system is ready to receive voice commands and carry out the voice commands, is called DI
ALOGUE. The system gives audible feedback
and guides you if necessary th
rough the relevant functions.
You can end the dialogue at any time by pressing the PTT button
 on the adapter*
 page 108, fig. 106
or on the multifunction steering
wheel* (press for a long period
of time to start or briefly press to end)
page 108 or end it with the voice command
CANCEL
.
When receiving an incoming call, the dialog
ue is immediately in
terrupted and you can
accept the call by pressing the button
 on the multifunction steering wheel* or by
pressing the button for receiving a call directly on your telephone. If a voice command is not detected, the system answers with “
Sorry?
” and a new entry
can be performed. After the 2nd error the system repeats the aid. After the 3rd error the answer “
Cancel
” is given and the dialogue is ended.
Optimum understanding of the voice commands depends on the following factors:
Speak with a normal tone of voice withou
t intonation and excessive voice pauses.

Avoid insufficient articulation.

Close the doors, windows and sliding roof, in order to reduce or stop disturbing
exterior noise.
It is recommended to speak louder at higher speeds, so that the tone of your voice
is louder than the increased surrounding noise.
During the dialogue avoid additional nois
e in the vehicle, e.g. simultaneously
talking occupants.
Do not speak, if the system makes an announcement.

The microphone for voice control is directed to the driver. Therefore, the device
may respond less well to commands of the front passenger.
Voice commandsThe voice control is possible in the following languages:
Czech, English, German, French, Italia
n, Spanish, Russian and Portuguese.
Voice commands for operating
the telephone control unit
After giving the command
DIAL NUMBER
, the system requests the entry of a tele-
phone number. The telephone number can be entered as an interconnected spoken row of digits (complete number), in the form
of order of digits
(separation through a
brief voice pause) or through individually
spoken digits. After each order of digits
(separation through brief voice pause) all of
the digits detected up to now are repeated
by the system. The digits
0 - 9
, symbols
+, , # are permitted. The system
detects no continuous digit
combinations such as twenty-three, but only
individually spoken digits (two, three).
Call name– Press the PTT button.
Voice command
Action
HELP
After this command the system repeats all possible commands.
CALL XYZ
With this command you call up the contact from the phone book
page 110.
DIAL NUMBER
After this command a phone number can be entered which establishes a connection to the requested party.
REDIAL
After this command the system selects the last selected number.
MUSIC
Play music from the mobile
phone or another paired
device.
OTHER OPTIONS
Selection for setting Bluetooth
®, dialogue etc.
CANCEL
The dialogue is ended.
s3j8.a.book Page 110 Tuesday, April 20, 2010 1:10 PM