2010 SKODA FABIA inflation pressure

Instruments and warning lights
31
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
Traction control system (TCS)*

The warning light
 lights up if the TCS
system is switched off.
Further information about the TCS
page 138.
Tyre pressure monitoring system*

The warning light
 lights up, if there is a substantia
l drop in inflation pressure in one
of the tyres. Reduce the speed and check or
correct as soon as possible the inflation
pressure in the tyres
page 178.
An audible signal sounds as an additional warning signal.If the warning light flashes
, there is a system fault. Visit the nearest specialist garage
and have the fault rectified. Further information about the tyre pressure monitoring system
page 142.
WARNING

When the warning light
 lights up, immediately reduce the speed and
avoid sudden steering and brake manoeuvr
es. Please stop the vehicle without
delay at the nearest possible stop and in
spect the tyres and their inflation pres-
sures.
Under certain circumstances (e.g. sporty style of driving, wintry or unpaved
roads) the warning light
 can be delayed or does not light up at all.
Note
If the battery has been disconnected, the warning light
 comes on after switching on
the ignition. The warning light must go out after driving a short distance.Selector lever lock*

(automatic gearbox)
If the
green
warning light
 lights up, operate the brake pedal. This is necessary, in
order to be able to move the selector lever out of the position
P or N.
Further information about the selector lever lock
page 100.
Traction control system (TCS)*

The warning light
 comes on for a few seconds when the ignition is switched on.
The warning light flashes when a control cycle is activated while driving.The warning light
 lights up permanently if there is a fault in the TCS system.
The fact that the TCS system operates together with the ABS means that the TCS warning light will also come on if the ABS system is not operating properly. If the warning light
 comes on immediately after starting the engine, the TCS system
can be switched off for techni
cal reasons. In this case, the TCS system can be switched
on again by switching the igni
tion on and off. If the warning light goes out, the TCS
system is fully functional again. Further information about the TCS
page 138, “Traction control system (TCS)*”.
Note
If the battery has been disconnected
and reconnected, the warning light
 comes on
after switching on the ignition. The warning light must go out after driving a short distance.Electronic stability programme (ESP)*

The warning light
 comes on for a few seconds when the ignition is switched on.
If the ESP helps to stabilise the vehicle (f
or example when applying and releasing a
braking force to an individual wheel), then the indicator light
 flashes.
The warning light
 lights up permanently if there is a fault in the ESP system.
The fact that the ESP system operates together with the ABS means that the ESP warning light will also come on if the ABS system is not operating properly. If the warning light
 comes on immediately after starting the engine, the ESP system
can be switched off for technical reasons. In
this case, the ESP system can be switched
on again by switching the igni
tion on and off. If the warning light goes out, the ESP
system is fully functional again. Further information on the ESP
page 137, “Electronic stab
ility programme (ESP)*”.
s3j8.a.book Page 31 Tuesday, April 20, 2010 1:10 PM

Passive Safety
113
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
SafetyPassive SafetyBasic informationDriving the safe way Passive safety measures reduce the risk
of injury in accident situations.
In this section you will find important info
rmation, tips and notes on the subject of
passive safety in your vehicle. We have
combined everything here which you should
be familiar with, for example, regarding seat
belts, airbags, child seats and safety of
children. It is therefore important, in partic
ular, to comply with the notes and warnings
in this section for your own interest and in the interest of those travelling with you.
WARNING

This chapter contains important information on how to use the vehicle for
the driver and his occupants. You will find further information on safety, which concerns you and those travelling with you, in the following chapters of this Owner's Manual.
The complete on-board literature should always be in the vehicle. This
applies in particular, if you rent out or sell the vehicle.Safety equipment The safety equipment is part of the occupant protection and it can reduce the risk of injuries in accident situations.“Do not put at risk” your safety and the safety of those travelling with you . In the event of an accident, the safety equipment can redu
ce the risk of injuries. The following list
contains part of the safety
equipment in your vehicle:

three-point seat belts for all the seats;

belt force limiters for front seats;

belt tensioners for front seats;

seat belt height adjusters for front seats;

front airbags for the driver and the front passenger*;

side airbags*;

head airbags*;

anchoring points for child seat using the “ISOFIX” system;

anchoring points for child seat using the “Top Tether” system;

head restraints adjustable for height;

adjustable steering column.
The specified safety equipment works togeth
er, in order to optimally protect you and
those travelling with you in accident situat
ions. The safety equipment does not protect
you or the people travelling with you, if
you or your occupants adopt an incorrect
seated position or the equipment is
not correctly adjusted or used.
For this reason you will be provided with information on why this equipment is very important, how it protects you and the occupants, what should be observed when using the equipment and how you and the peop
le travelling with you can make full use
of the existing safety equipment. This
Owner's Manual contains important warning
notes, which you and those travelling with
you should pay attention to in order to
reduce a risk of injury. Safety concerns everybody!Before setting off The driver is always fully responsibl
e for his occupants and for the oper-
ating safety of the vehicle.For your own safety and the safety of the pe
ople travelling with you, please pay atten-
tion to the following points before setting off.
Ensure that the lighting and the turn signal system are functioning properly.

Inspect the tyre inflation pressure.
s3j8.a.book Page 113 Tuesday, April 20, 2010 1:10 PM

Intelligent Technology
142
You will place great stresses on the power steering system if the steering is turned to full lock when the vehicle is stationary. Turn
ing the steering to full lock in such a situa-
tion will be accompanied by noises. It is still possible to fully steer the vehicle if the power steering fails or if the engine is not running (vehicle being towed in). The only
difference is that gr
eater physical effort
is required. It is possible that the hydraulic pump of
the power steering will not run due to the low
vehicle network voltage if the battery has gone flat and the engine must started with the help off jump leads. This condition will
be indicated by lighti
ng up of the warning
light. The power steering operates again if the ba
ttery is charged to a specific range when
engine is running. It also op
erates again, if the engine
can be started with its own
battery. If there is a fault in the power steering, the warning light lights up in the instrument cluster
 page 26.
Caution
Do not leave the steering at full lock fo
r more than 15 seconds when the engine is
running - risk of damagi
ng the power steering!
Note
Have the steering inspected as soon as possible by a specialist garage if there is a leak or fault in the system.
Tyre pressure monitoring system*The tyre pressure monitoring system compares with the aid of the ABS sensors the speed and also the rolling circumference of the individual wheels. If the tyre inflation pressure is significantly changed and thus the rolling circumference of a wheel, the warning light
 lights up in the instrument cluster
page 31. The tyre pressure moni-
toring system functions late or too sensitively if:
the structure of the tyre is damaged,

the vehicle is loaded to one side or with a load on the roof,

the wheels of an axle are loaded heavily (e.g. when towing a trailer or when driving
uphill or downhill),
the vehicle is operated in unfavourable wi
nter conditions or
on an unfirm ground,

snow chains or emergency wheel* are mounted,

the driver has a sporty style of driving (with sharp acceleration and high speed
when cornering). Basic setting of the system After changing the tyre inflation pressures
or after changing one or several wheels, a
basic setting of the system mu
st be carried
out as follows.

Inflate all tyres to the specified inflation pressure
page 178.

Switch on the ignition.

Press button
 
fig. 131
for more than 2 seconds. While pressing the button,
the warning light
 lights up. At the same time the basic values are stored, which is
confirmed with an acoustic sound and then the warning light
 goes out.
Fig. 131 Button for setting the tyre inflation pressure control value
s3j8.a.book Page 142 Tuesday, April 20, 2010 1:10 PM

Intelligent Technology
143
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data

If the warning light
 does not go out after the basic setting, there is a fault in the
system. Have the vehicle inspected by your nearest specialist garage. Functional description After the basic setting of the system the “adaptation” of the tyre inflation pressures and then the tyre pressure control in the individual tyres are performed. Warning light
 lights up
If the tyre inflation pressure of at least one wheel is insufficiently inflated in comparison to the stored basic value, the warning light
 
lights up. Inflate all tyres to the
specified inflation pressure
page 178, “Tyre life” and then perform a basic setting of
the system. Warning light
 flashes
If the warning light flashes, there is a system fault. Have the vehicle inspected by your nearest specialist garage.
WARNING

When the warning light
 lights up, immediately reduce the speed and
avoid sudden steering and brake manoeuvr
es. Please stop the vehicle without
delay at the nearest possible stop and in
spect the tyres and their inflation pres-
sures.
The driver is responsible
for the correct tyre inflation pressures. For this
reason, the tyre inflation pressu
res must be checked regularly.

Under certain circumstances (e.g. sporty style of driving, wintry or unpaved
roads) the warning light
 can be delayed or does not light up at all.

The tyre pressure monitoring system does not take away the responsibility
from the driver for the correct tyre inflation pressure.
Note
The tyre pressure monitoring system:
does not replace the regular tyre inflatio
n pressure control, because the system
cannot detect an even pressure loss;

cannot warn in case of very rapid tyre inflation pressure loss, e.g. in case of sudden
tyre damage. In this case ca
refully bring the vehicle to a standstill without sudden
steering movements and without sharp braking.Diesel particle filter* (diesel engine)In the diesel particle filter the resu
lting soot particles are collected and
burnt during the combustion of diesel fuel.Code
7GG
, 7MB
or 7MG
on the vehicle data sticker, see
fig. 132
, indicates that your
vehicle is equipped with a diesel particle fi
lter. The vehicle data st
icker is located on
the floor of the luggage compartment and is
also stated in the Service schedule.
The diesel particle filter filters the soot particles completely from the exhaust. The soot is collected in the diesel particle filter and
burnt regularly. To assist this procedure, we
recommend not to drive regu
larly over short distances.
If the diesel particle filter is clogged or there is a fault, it is indicated by the warning light 
page 33, “Diesel particle filter*
 (diesel engine)”.
WARNING

The diesel particle filter
achieves very high temp
eratures. Therefore do not
park at points where the hot filter comes into direct contact with dry grass or other combustible materials - risk of fire!
Never use additional underbody protection or corrosion-protection agents
for the exhaust pipes, catalytic converters,
heat shields or diesel particle filter. Fig. 132 Vehicle data sticker
s3j8.a.book Page 143 Tuesday, April 20, 2010 1:10 PM

Driving and the Environment
149
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
Checking tyre inflation pressures Tyres which are correctly inflated save fuel.Always ensure that your tyres are inflated to the correct pressure at all times. The rolling resistance will be increased if the tyre filling pressure is too low. This will not only increase fuel consumption but also tyre we
ar and the driving behaviour will worsen.
Always check the inflation pr
essure of the tyres when
cold
.
Do not drive with
winter tyres
all year round for this costs about 10 % more fuel.
Winter tyres are also louder.No unnecessary ballast Transporting ballast costs fuel.The fact that every kilogram of extra
weight
increases your fuel consumption means
that it is worth taking a look in the luggage compartment to avoid transporting any unnecessary ballast. It is particularly in town traffic, when one
is accelerating quite often, that the vehicle
weight will have a significant effect upon
the fuel consumption. A rule of thumb here
is that an increase in weight of 100 kilograms will cause an increase in fuel consump- tion of about 1 litre/100 kilometres. You may frequently also leave a
roof rack fitted
on just out of convenience, although
you no longer need it. The increased aerodyna
mic drag of your vehi
cle causes it to use
about 1 l more fuel than normal at a speed of 100 - 120 km/h, even when you are not carrying a load on the roof.Saving electricity Generating electricity costs fuel.– Switch off electrical components as
soon as you no longer need them.
When the engine is running, th
e alternator generates and supp
lies electrical power. If
more electrical components of the electrical system are switched on, more fuel is needed to operate the alternator.
Keeping a log of your fuel consumptionIf you really wish to keep a close check on your
fuel consumption
, it is best to enter
the figures in a logbook. This does not take much time but is a very worthwhile exer-cise. It enables you to detect any change (p
ositive and negative) at an early stage and
to take any appropriate action. If you find that your fuel
consumption is too high, you should reflect on how, where
and in what conditions you have driven
the vehicle since you last refuelled.
Environmental compatibilityEnvironmental protection has played a major role in the design, selection of materials and manufacture of your new Škoda. Particular emphasis has been paid to a number of aspects, including: Design measures
Joints designed to
be easily detached.

Simplified disassembly due to the modular structure system.

Improved purity of differ
ent classes of materials.

Identification of all plastic parts in
accordance with VDA Recommendation°260.

Reduced fuel consumption
and exhaust emission CO
2.

Minimum fuel leakage during accidents.

Reduced noise.
Choice of materials
Extensive use of re
cyclable material.

Air conditioning filled with CFC-free refrigerant.

No cadmium.

No asbestos.

Reduction in the “vaporisation” of plastics.
Manufacture
Solvent-free cavity protection.
s3j8.a.book Page 149 Tuesday, April 20, 2010 1:10 PM

Towing a trailer
152
Towing a trailerTo w i n g a t r a i l e rTechnical requirements The towing device must satisfy certain technical requirements.Your vehicle is designed primarily for tr
ansporting persons and luggage. It can,
however, also be used for towing a traile
r - provided certain technical equipment is
fitted. If your vehicle has been eq
uipped with a towing device
from Škoda Original Accesso-
ries, then the towing device satisfies all technical and legal requirements. Your vehicle is fitted with a 13-pin power so
cket for the electrical connection between
the vehicle and trailer. If the tr
ailer which you wish to tow has a
7-pin connector
, you
can use a suitable adapter
12) from Škoda original accessories.
This work must be carried out in accordance
with the manufacturer's specifications if
a towing device is retrofitted. Specialist garages are familiar with details re
lating to retrofitting a towing device and
for any necessary modifications to the cooling system.
WARNING
We recommend that you have the towing device from Škoda original accesso-ries installed by a specialist garage. He
is familiar with all the relevant details
relating to retrofitting such equipment. There is a risk of an accident if the towing device is not properly fitted!General Maintenance There are a number of points to pay attention to when towing a trailer.Trailer load The permissible trailer load must
on no account be exceeded.
You can negotiate appropriately steeper inclin
es and descents if you do not make full
use of the permissible trailer load. The trailer loads specified only apply for
altitudes
up to 1 000 metres above mean sea
level. On petrol engines without forced indu
ction, the engine power output drops with
increasing height due to a lowering of air pr
essure and thus the ability to climb, this
means that the trailer load must be reduced by 10% for every further increase of 1 000 metres in height above sea le
vel. The towed weight is the weight of the (laden) vehicle
and the (laden) trailer together. One should ta
ke this into account before driving up to
higher altitudes. Petrol engines with forced induction use an air pressure correction method, so that their power output does
not depend on the he
ight above sea level.
The trailer and drawbar load information on the type plate of the towing device are merely test data for the towing device
The data relating to your vehicle, which
is often less than this test data, can be found in your vehicle registration docu- ments. Distribution of the load Distribute the load in the trailer in such a
way that any heavy items are located as close
as possible to the axle. Secure th
e items to preven
t them slipping.
Tyre pressure Correct the tyre inflation pressure on yo
ur vehicle for that of “fully laden”,
page 178.
The inflation pressure of the tyres fitted to
the trailer adjust in accordance with the
manufacturer's recommendation. Exterior mirrors You have to have additional ex
terior mirrors fitted if you are not able to see the traffic
behind the trailer with the standard rear-view mirrors. Both exterior mirrors should be attached to folding arms. Adjust the mirrors so that they provide you with an adequate field of view to the rear. Headlights Before starting off with a hitched trailer, al
so check the setting of the headlights. Alter
the setting as necessary with the aid of the headlight beam adjuster
page 51.
12)In some countries the adapter is supplied with the towing device.s3j8.a.book Page 152 Tuesday, April 20, 2010 1:10 PM

Wheels and Tyres
178
Wheels and TyresWheelsGeneral information
New tyres do not offer optimal grip at first and should therefore be run in for about
500 km at a moderate speed and an appropri
ately cautious style of driving. You will
also profit from longer tyre life.
The tread depth of new tyres may differ be
cause of design features and the config-
uration of the tread (depending on the type of tyre and the manufacturer).
Drive over curbs on the side of the road
and other such obstacles slowly and,
where possible, at a right angle in order
to avoid damage to tyres and wheel trims.

Inspect your tyres from time to time
for damage (punctures, cuts, splits and
bulges). Remove foreign bodies from the tyre profile.
Damage to tyres and wheels is frequently
not visible. Unusual vi
brations or pulling
of the vehicle to one side coul
d be a sign of tyre damage.
Please reduce your speed
immediately and stop if you su
spect that a wheel is damaged.
Inspect the tyres for
signs of damage (bulges, splits, etc.). If no
visible damage is present, please drive at an
appropriately slow speed and carefully to the nearest specialist garage in order to have your vehicle inspected.
Also protect your tyres from contact with oil, grease and fuel.

Immediately replace any dust caps of
the valves which have got lost.

Mark wheels before removing them so that
their previous dire
ction of running can
be maintained when mounted them again.
Always store wheels or tyres which been removed in a cool, dry and, where
possible, dark place. Tyres which are not fixed to a wheel trim should be stored upright. Unidirectional tyres* The direction of rotation of the tyres is mark
ed by arrows on the
wall of the tyre. This
indicates the direction of rotation of the tyre, and it is essential that the tyres are fitted on to run in this direction. Only then are
the tyres able to provide the optimal proper-
ties in terms of grip, low nois
e, wear-and-tear and aquaplaning.
Further information concerning th
e use of unidirectional tyres
page 182.
WARNING

New tyres during the first 500 km do not offer optimal grip and should
therefore be run appropriately - risk of accident!
Never drive with damaged tyres - risk of accident!Note
Please observe the various differing legal requirements regarding tyres.Ty re l i feThe life of your tyres very much depends on the following points: Tyre pressure The working life of tyres will be shortened considerably if the tyres are insufficiently or over-inflated and this will have an adverse
effect on the handli
ng of your vehicle.
Correctly inflated tyres are of particular importance when travelling at
high speeds
. It
is therefore good to check the pressure at
least once a month and also before setting
off on a long trip. Please do not forget the spare wheel* when checking the tyres. The tyre inflation pressures for
summer tyres
are indicated on the inside of the fuel
filler flap
fig. 147
. The inflation pressures for
winter tyres
are 20 kPa (0.2 bar) higher
than those for summer tyres
page 182.
Fig. 147 An opened fuel filler flap with a tyre size and tyre inflation pressure table
s3j8.a.book Page 178 Tuesday, April 20, 2010 1:10 PM

Wheels and Tyres
179
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
The tyre pressure should be
at the highest pressure specified for your vehicle at all
times. Always check the inflation pressure of tyres
when cold. Do not reduce the higher pres-
sure of warm tyres. Adapt the inflation pressure of the tyres accordingly if your vehicle is carrying a significantly higher payload. Tyre inflation pressure - Tyre size 185/55 R15 The same inflation pressure values apply to ty
res of the tyre size 195/55 R15 as to tyres
of the tyre size 185/55 R15 which are intended to be used with snow chains, see the inside of the fuel filler flap. The tyres of the tyre size 185/55 R15, which are intended to be used with snow chains and are fitted on models Fabia Combi Scout, have the following inflation pressure values in kPa. Driving style Fast cornering, sharp acceleration and brak
ing (squealing tyres) increase wear-and-
tear on your tyres. Balancing wheels The wheels of a new vehicle are balanced. There are a wide range of influences when driving which may result in an imbalance
and which makes themselves felt through
vibration in the steering.
You should have the wheels rebalanced si
nce any imbalance increases wear-and-tear
on the steering, the suspension and tyres. A wheel must also be rebalanced when a new tyre is fitted and each time a tyre is repaired. Wheel alignment errors Incorrect wheel alignment at the front and rear
will not only increase wear-and-tear on
the tyres but will also has an adverse effect on vehicle safety. Contact your specialist garage if you notice any unusual tyre wear.
WARNING

If the inflation pressure is too low,
the tyre must perform a higher rolling
resistance. At higher speeds the tyre will warm up as a result of this. This can result in tread separation and even a tyre blowout.
Immediately replace the damaged rims or tyres.

Tyres which are 6 years old or more should only be fitted in exceptional
cases and when adopting an approp
riately cautious style of driving.
For the sake of the environment
Tyres which are insufficiently inflated increase your fuel consumption.Wear indicatorsThe base of the tread of the original tyres has wear indicators 1.6 mm high, installed at right angles to the direction of travel. These
wear indicators are lo
cated at 6 - 8 points
depending on the make and are evenly spaced around the circumference of the tyre
Engine
Partial load
Full load
1.2/63 kW TSI
220/230
220/230
1,4/63 kW
220/290
1.2/77 kW TSI
230/300
1.6/77 kW
230/300
1,2/55 kW TDI CR
230/300
1.6/66 kW TDI CR
220/290
1.6/77 kW TDI CR
220/290
Fig. 148 Tyre tread with wear indicators
s3j8.a.book Page 179 Tuesday, April 20, 2010 1:10 PM