2010 SKODA FABIA Eco

Seats and Storage
61
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
Heating the front seats*You can electrically heat the seat cushions and the seat backrests of the front seats. – By pressing the rocker switch in the posi
tion or switch on the front seat
heating to 25% or 100% of its power output
fig. 52
.
– To switch off the heating shift the rocker switch into the horizontal position.
WARNING

If, as an occupant, you have a subdued
pain and/or temperature sensitivity,
e.g. through medication, paralysis or beca
use of chronic illness (e.g. diabetes),
we recommend not to use the seat heating of the driver or front passenger seat. This can lead to burns on the back, the
posterior and the legs
which are difficult
to heal. If the seat heating is used, we
recommend to make regular breaks in
your journey when driving long distances,
so that the body can recuperate from
the stress of the journey. Please consult your doctor, who can evaluate your specific condition.
Caution

You should not kneel on the seats or otherwise apply pressure at specific points in
order to avoid damaging the heating elements of the seat heaters.
Do not use the seat heating if the seats are not occupied by persons or if objects
are fastened or stored on them, for example a child seat, a bag etc. A fault of the heating elements in the seat heating can occur.
Do not clean the seats moist
page 160.
Note
The seat heating should only be switched
on when the engine is running. This has a
significant effect of saving
on the battery capacity.
Rear seatsFolding the rear seats forwardsFig. 53 Fold the seat cushion forwards / unlock the seat backrestTo enlarge the luggage compartment, the rear
seats can be folded forwards, if neces-
sary remove the seat cushions
page 62. The rear seats can be folded forward indi-
vidually on vehicles with divided rear seats*.Folding seats forwards– Before folding the rear seats forwards, yo
u must adapt the position of the front
seats in such a way that they are not damaged when the rear seats are folded forwards.
– Pull up the seat cushion in direction of arrow
fig. 53
and fold forwards in
direction of arrow .
– Unlock the seat backrest by pressing th
e securing knob and fold it forwards
 fig. 53
on the right.
– Pull the head restraint out of the seat backrest.
Fig. 52 Rocker switch: Front seat heatingA1
A2
A1
A2
AA
s3j8.a.book Page 61 Tuesday, April 20, 2010 1:10 PM

Seats and Storage
68 Remove carrier rails– Slacken the check points on the carrier rails using the vehicle key or a flat screw-
driver
page 67, fig. 63
.
– Grasp the carrier rail
at the position
page 67, fig. 63
and slacken it by
pulling in the direction of the arrow.
You can take out the removable storage
compartments* in order to facilitate the removal
page 78, “Removeable storage
compartments* in the luggage compartment”.
– Grasp the carrier rail at the position ,
slacken it by pulling in the direction of
the arrow and take it out.
– The carrier rail on the other side of
the luggage compartment can be removed in
the same way.
Install carrier rails– Position the carrier rails on the
sides of the luggage compartment.
– Press both check points on each carrier rail up to the stop.– Check the attachment of the
carrier rails by pulling it.
WARNING
Pay attention when installing that the ca
rrier rails and the variable loading floor
are correctly fixed, otherwise
the occupants are at risk.
Divide the luggage compartment with variable loading floor*
The luggage compartment can be divided with the variable loading floor. – Lift up the part with the holder and se
cure it by sliding it into the grooves
 fig. 64
.
Net partition* (Combi)Use the net partition behind the rear seatsFig. 65 Pull out the net partition / roll upPulling out– Open the right rear door. – Fold down the rear seat backrests slightly forwards, which makes it possible to clear
the access for unrolling the net partition.
– Pull the net partition at the bracket out of the housing in direction of the
holders
fig. 65
.
– Insert the cross rod into one of the mounts .– Insert the other end of the cross rod by pressing into the second mount.– Press both ends of the cross rod
forward into the function position.
– Then push the seat backrest back into th
e upright position until the locking button
clicks into place - check by pulling on the seat backrest

.
AB
AA
A1
AA
A2
Fig. 64 Divide the luggage compart- ment
AA
AB
AC
AC
s3j8.a.book Page 68 Tuesday, April 20, 2010 1:10 PM

Seats and Storage
69
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
Folding– Pull the cross rod back slightly, first on the one side then on the other side and take
the cross rod out of the mounts
page 68, fig. 65
.
–
Hold
the cross rod in such a way that the net partition can roll up slowly and
without damage into housing .
If you wish to use the entire luggage
compartment, you can remove the luggage
compartment cover
page 66.
WARNING

Ensure that the seat backrest on the rear seats is securely interlocked in
position when the vehicle is fitted with three-point safety belts for the middle rear seat. It is only then that the three-point seat belt can reliably fulfil its func-tion.
First check for yourself that the cross road is inserted into the mounts in
the front position!
If the net partition is located behind th
e rear seats, then always make sure
that the rear seat backrest is correctly interlocked.Using the net partition behind the front seatsFig. 66 Pull out the net partition / roll upPulling out– Open the right rear door.
– Fold the surfaces of the seats and seat backrests of the rear seats forward. – Pull the net partiton net at the plate out of the housing
fig. 66
.
– First of all insert the cross rod into the mount on one side.– Insert into the mount on the other side the second end of the cross rod.– Press both ends of the cross rod
forward into the function position.
Folding– Pull the cross rod back slightly, first on the one side then on the other side and take
the cross rod out of the mounts
fig. 66
.
–
Hold
the cross rod in such a way that the net partition can roll up slowly and
without damage into housing .
– Fold the rear seats back into their original position.
WARNING
First check for yourself that the cross road is inserted into the mounts in the front position!Removing and installing net partition housingRemoving– Open the right rear door.
ACAB
AC
AA
AB
AC
ACAB
AC
Fig. 67 Rear seats: Net partition housing
s3j8.a.book Page 69 Tuesday, April 20, 2010 1:10 PM

Seats and Storage
70– Fold the surfaces of the seats and seat backrests of the rear seats forward. First the
right then the left backrest.
– Push the net partition housing
page 69, fig. 67
in the direction of arrow
and take it out of the mounts of the rear se
at backrests on the right in the direction
of the arrow .
Installing– Position the net partition housing into the mounts of the rear seat backrests. – Push the luggage net partition housing in
the opposite direction of arrow as far
as the stop.
– Fold the rear seats back into their original position.Bicycle holder in the luggage compartment*Install cross member– Remove the luggage compartment cover
page 66; if necessary we recommend
to remove, the net partition*
page 69.
– Take the head restraints out of the rear
seat backrests and fold the rear seats in
order to extend the luggage compartment as desired.
– Release the fixtures at the ends of
the cross member by fully loosening and
slightly pulling up
the securing screws . The fixtures open when they are not
already opened.
– Position the cross member with the fixed
(not pulled out) part onto the right (in
direction of travel) lashing eye and then the pull out part onto the left lashing eye.
– Press the fixtures on both sides of the cross member until they lock in place and
tighten the securing screws .
– Check the attachment of the cross member by pulling it.
WARNING
When transporting the bicycles in the
luggage compartment, ensure the safety
of the passengers transported.Install bicycle carrier– Position the approved bicycle carrier on
the middle of the cross member, after
pulling up the screw push the frame side rail (alu-part) towards the cross member and screw the screw into the nut
fig. 69
.
– Slacken the screw and take it out of the moveable part of the fixture; position
the moveable part of the carr
ier, depending on bicycle size
, into one of the possible
positions, so that it does not come in contact with the boot lid. We recommend to place the moveable part of the fixture in such a position that the holes are visible between the screw and the moveable part.
– Insert the screw into the desired position and tighten.
AA
A1
A2
A1
Fig. 68 Install cross member
AB
AC
AA
AB
AC
Fig. 69 Install bicycle carrier
AA
AA
ABAA
AB
s3j8.a.book Page 70 Tuesday, April 20, 2010 1:10 PM

Seats and Storage
71
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
Put bicycle into the bicycle carrierFig. 70 Put in the bicycle / fastening the front wheel– Remove the front wheel before putti
ng the bicycle into the vehicle.
– Slacken the quick tension jack on the fixi
ng axle of the bicycl
e carrier and adjust
according to the width
of the bicycle fork.
– Fit the bicycle fork onto
the fixing axle and tighten with the quick tension jack
 fig. 70
.
– Position the left pedal of the bicycle forward, in order to attach the front wheel
more easily.
– Slacken the screw
page 70, fig. 69
and push the bicycle
holder together with
the attached bicycle to the le
ft (in the direction of the arrow), so that no collision
between the steering arm and the side wi
ndow of the luggage compartment can
occur.
– Carefully guide the boot lid to the bottom
without letting it go and at the same time
check if there is adequate room between
the steering arm of the bicycle and the
window of the boot lid. If necessary adapt
the position of the moveable part of the
bicycle carrier in such a way that no collision can occur
page 70.
– It is best to push the removed front wheel between the crank of the left pedal and
the bicycle frame, attach it wi
th a strap to the front fork
fig. 70
, and/or to a fixing
point.
– Make sure that it does not lead to da
mage of the trim panel of the luggage
compartment, the bicycle and the placed objects.
– Perform the installation of the second
fixture and the attachment of the bicycle
analogously.
WARNING
Place the bicycles in the bicycle carrier in such a position that no collision between the steering arm and the side
and/or rear window can occur.
Note
If the front wheel is equipped with disc brake, attach the wheel in such a way that the brake disc is opposite the frame.Secure the stability of the bicycles with a strapFig. 71 Securing the bicycles with clamps / securing the bicycles with a strap– To slacken the rubber part of the clamp,
push both parts against each other and
open the clamp.
– Position the clamp with the rubber part to the front (in direction of travel) as far as
possible below the saddle
rod and close the clamp
fig. 71
.
– When transporting two bi
cycles tension the strap
fig. 71
between the saddle
rods, by pushing the bicycles apart.
– Hang the carabines at the ends of the strap into the lashing eyes behind the rear
seats.
– Pull the strap through the tensioning clasp,
first of all on the one side and then on
the other side.
AA
s3j8.a.book Page 71 Tuesday, April 20, 2010 1:10 PM

Seats and Storage
76Storage compartments on the front passenger side*On some vehicles, the storage compartments are not equipped with lids.Opening and closing the storage compartments on the front passenger side– Pull the handle of the lid in direction of arrow
fig. 79
and fold it open.
– Swivel the flap until it is heard to lock. A pin holder is located
inside the lower flap.
WARNING
The storage compartments must always be closed when driving for safety reasons.
Cooling of storage compartment on front passenger side* The storage compartment ca
n be fitted for vehicles with an air-condi-
tioning system with a closable inlet for cooled air.– You can switch the cooling system on or off using the control dial
fig. 80
.
Opening the air inlet when the air conditioning system is on causes fresh or interior air to flow into the storage compartment. We recommend that you switch off the cooling if it is operating in the heating mode or if you are not using the cooling system for the storage compartment.Storage compartment on the driver's sideUnlockable compartment below the steering wheel on the left.
Fig. 79 Dash panel: Storage compart- ments on the front passenger side
Fig. 80 Storage compartment: Using cooling system Fig. 81 Dash panel: Storage compart- ment on the driver's side
s3j8.a.book Page 76 Tuesday, April 20, 2010 1:10 PM

Heating and air conditioning system
82Set heatingRecommended settings of
heating controls for:
Note
We recommend that you leave the air outlet vents
3 page 80, fig. 89
in the opened
position.
Setup
Setting of the control dial
Button
Air outlet vents 3
Air outlet vents 4
Defrosting the windscreen and side windows
To the right up to
the stop
3

Do not switch on
Closing
Open and align with the side
window
Free windscreen and side win- dows from mist
Desired tempera-
ture
2 or 3

 
Do not switch on
Closing
Open and align with the side
window
The fastest heating
To the right up to
the stop
3

briefly switched on
Opening
Opening
Comfortable heating
Desired tempera-
ture
2 or 3

Do not switch on
Closing
Opening
Fresh air mode - ventilation
To the left up to the
stop
Desired position

Do not switch on
Opening
Opening
A1
AA
AB
AC
s3j8.a.book Page 82 Tuesday, April 20, 2010 1:10 PM

Heating and air conditioning system
83
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
Climatic (semi-automatic air conditioning system)*Description Climatic is a combined cooling an
d heating system with electronic
control of the convenience temperature in the vehicle interior. It makes it possible to optimally control the air temperature at any season of the year.Description of the Climatic It is important for your safety and for your
driving comfort that the Climatic is operating
properly. The air conditioning system operates when switch
page 83, fig. 91
is
pressed and the following
conditions are met:

engine running,

outside temperature above +2°C and

blower switch switched on (positions 1 to 4).
If the cooling system is switched on, the temperature and air humidity drops in the vehicle. The wellbeing of the occupants of the
car is enhanced as a result of this partic-
ularly at high outside temperatures and a
high air humidity. The system prevents the
windows misting up during th
e cold season of the year.
The heating effect is dependent upon the c
oolant temperature, thus
full heat output
only occurs when the engine has reached its operating temperature. It is possible to briefly activate recirculat
ed air mode in order to enhance the cooling
effect

.
Air at a temperature of about 5°C may flow
out of the vents under certain circum-
stances when the cooling system is operatin
g. Lengthy and uneven distribution of the
air flow out of the vents (in particular at the leg area) and large differences in temper-ature, for example when getting out of the ve
hicle, can result in chills in sensitive
persons. The air inlet in front of the windscreen must
be free of ice, snow or leaves in order to
ensure that the heating and cooling systems operate properly.
After switching on the cooling
Condensation
from the evaporator of the air condi-
tioning may drip down and form a puddle be
low the vehicle. This is quite normal and
not an indication of a leak!
WARNING

For your own safety and that of other road users, ensure that all the
windows are free of ice, snow and misting. Please familiarize yourself about how to correctly operate
the heating and ventilation systems, how to demist
and defrost the windows, as well as with the cooling mode.
You should not leave recirculated air mode on over a longer period of time,
as “stale” air may result in fatigue in the driver and occupants, divert your attention and also cause the windows to mist up. The risk of having an accident increases. Switch recirculated air mo
de off as soon as the windows begin
misting up.
Note

We recommend that you do not smoke in
the vehicle when the recirculating air
mode is operating since the smoke which is drawn at the evaporator from the interior of the vehicle forms deposits in the evapor
ator of the air conditioning system. This
produces a permanent odour when the Climat
ic is operating which can only be elimi-
nated through considerable effort and
expense (replacement of compressor).
Using the system
AC
AE
Fig. 91 Climatic: Control elements
s3j8.a.book Page 83 Tuesday, April 20, 2010 1:10 PM