2010 SKODA FABIA remove seats

Lights and Visibility
57
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data

You should clean the wiper blades regu
larly with a windscreen cleaner in
order to avoid any smears. Clean a wiper blad
e with a sponge or cloth if it is very
dirty, for example from insect residues.
Replace the wiper blades once or twice a year for safety reasons. The wiper
blades are available from specialist garages.Replacing the wiper blade on the rear window wiperTaking off the wiper blade– Fold windscreen wiper arm out from the windscreen and position the wiper blade
at right angles to the wiper arm
fig. 48
.
– Hold the window wiper arm at the top end with one hand.– With the other hand unlock the locking button in the direction of arrow and
remove the wiper blade.
Attaching a wiper blade– Position the wiper blade onto the wiper arm and lock the locking button . – Check whether the wiper bl
ade is correctly attached.
The same remarks apply here as for
page 56.
Rear mirrorYou can adjust the exterior mirrors electrically*.Adjust the rear mirror before commencing to drive so that there is a clear view to the rear.Dimming the interior mirror– Pull the lever on the bottom edge of the mirror toward rear (the lever on the inte-
rior mirror must point forwards in it home position).
Heating of the external mirror*– Turn the rotary knob to position
 fig. 49
.
Adjusting the left-hand exterior mirror*– Turn the rotary knob to position
. The movement of the mirror surface is identical
to the movement of the rotary knob.
Adjusting the right-hand exterior mirror*– Turn the rotary knob to position
. The movement of the mirror surface is identical
to the movement of the rotary knob.
The vehicle can also be equipp
ed with a second rear mirror*, which is attached above
the inner main rear mirror. Th
e second rear mirror* enables an extensive look into the
area of the rear seats, e.g. to check on the seated passengers. You can adjust it in the horizontal as well as vertical direction re
gardless of the inner main rear mirror.
WARNING (continued)
Fig. 48 Wiper blade for rear windowAA
AA
Fig. 49 Inner part of door: Rotary knob
s3j8.a.book Page 57 Tuesday, April 20, 2010 1:10 PM

Seats and Storage
60 Adjust the angle of the seat backrest– Relieve any pressure on the seat backrest
(do not lean on it) and turn the hand-
wheel to adjust the angle of the backrest.
The driver's seat should be adjusted in such a way that the pedals can be fully pressed to the floor with slightly bent legs. The seat backrest on the driver's seat should
be adjusted in such a way that the upper
point of the steering wheel can be easi
ly reached with slightly bent arms.
WARNING

Only adjust the driver seat when the vehicle is stationary - risk of injury!

Take care when adjusting the seat! Adjusting the seat without care can lead
to bruises or injuries.
The seat backrests must not be angled too far back when driving otherwise
this will affect proper operation of the se
at belts and of the airbag system - risk
of injury!Head restraintsFig. 51 Head restraint: Adjusting / pulling outBest protection is achieved if the top edge of
the head restraint is at the same level as
the upper part of your head.
Adjusting the height of a head restraint– Grasp the side of the head restraint with both hands and push the head restraint in
the direction of axle of the metal guide rods, in the direction of arrow to the top or to the bottom
fig. 51
on the left.
– Move the head restraint downwards if required by pressing the locking button
 fig. 51
on the right and by pressing with the other hand the head restraint down-
wards.
Removing and installing a head restraint– Pull the head restraint out of the seat backrest as far as the stop. – Press the locking button in the direction of arrow
fig. 51
and pull the head
restraint out.
– To re-insert the head restraint, push it do
wn into the seat backrest far enough until
you hear the locking button engage.
The position of the front, rear outer head restraints and the rear middle head restraint* is adjustable for height. The head restraints must be adjusted to ma
tch the size of the seat occupant. Correctly
adjusted head restraints together with the
seat belts offer effective protection for the
occupants
page 114.
WARNING

The head restraints must be correctly adjusted in order to offer effective
protection for the occupants in the event of an accident.
Do not drive under any circumstance with removed head restraints - risk of
injury!
If the rear seats are occupied, the rear
head restraint must not be in the
lower position.
A3
s3j8.a.book Page 60 Tuesday, April 20, 2010 1:10 PM

Seats and Storage
61
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
Heating the front seats*You can electrically heat the seat cushions and the seat backrests of the front seats. – By pressing the rocker switch in the posi
tion or switch on the front seat
heating to 25% or 100% of its power output
fig. 52
.
– To switch off the heating shift the rocker switch into the horizontal position.
WARNING

If, as an occupant, you have a subdued
pain and/or temperature sensitivity,
e.g. through medication, paralysis or beca
use of chronic illness (e.g. diabetes),
we recommend not to use the seat heating of the driver or front passenger seat. This can lead to burns on the back, the
posterior and the legs
which are difficult
to heal. If the seat heating is used, we
recommend to make regular breaks in
your journey when driving long distances,
so that the body can recuperate from
the stress of the journey. Please consult your doctor, who can evaluate your specific condition.
Caution

You should not kneel on the seats or otherwise apply pressure at specific points in
order to avoid damaging the heating elements of the seat heaters.
Do not use the seat heating if the seats are not occupied by persons or if objects
are fastened or stored on them, for example a child seat, a bag etc. A fault of the heating elements in the seat heating can occur.
Do not clean the seats moist
page 160.
Note
The seat heating should only be switched
on when the engine is running. This has a
significant effect of saving
on the battery capacity.
Rear seatsFolding the rear seats forwardsFig. 53 Fold the seat cushion forwards / unlock the seat backrestTo enlarge the luggage compartment, the rear
seats can be folded forwards, if neces-
sary remove the seat cushions
page 62. The rear seats can be folded forward indi-
vidually on vehicles with divided rear seats*.Folding seats forwards– Before folding the rear seats forwards, yo
u must adapt the position of the front
seats in such a way that they are not damaged when the rear seats are folded forwards.
– Pull up the seat cushion in direction of arrow
fig. 53
and fold forwards in
direction of arrow .
– Unlock the seat backrest by pressing th
e securing knob and fold it forwards
 fig. 53
on the right.
– Pull the head restraint out of the seat backrest.
Fig. 52 Rocker switch: Front seat heatingA1
A2
A1
A2
AA
s3j8.a.book Page 61 Tuesday, April 20, 2010 1:10 PM

Seats and Storage
62– The head restraints can be inserted into
the relevant holes of the folded forward
seat cushions
fig. 54
.
– Fold the seat backrests fully fowards.Move seats into the initial position– Install the head restraint in the slightly lifted seat backrest.– Then push the seat backrest back into th
e upright position until the securing knob
clicks into place - check by
pulling on the seat backrest.
– Make sure that the red pin is covered
page 61, fig. 53
on the right.
– Move the seat cushion into its original position.
WARNING

Ensure that the seat belts are not da
maged when operating the seat back-
rests. Under no circumstances must the rear seat belts be jammed by the folded back seat backrests.
The belts and the belt locks must be in their original position after folding
back the seat cushions and the seat backrests - they must be ready to use.
Pay attention that the seat backrest is correctly interlocked. It is only then
that the three-point seat belt can reliably fulfil its function.
The seat backrests must be securely interlocked in position so that no
objects in the luggage compartment ca
n slide into the passenger compartment
if there is sudden braking - risk of injury!
Note
If the housing of the net partit
ion* is installed, first of all fold th left seat backrest
forward and then the right double seat backrest.
Inserting head restraints in the seat cushions– The rear head restraints can be inserted
into the relevant holes of the folded
forward seat cushions.
Removing the seat cushionThe luggage compartment can be increased in size by removing the rear seat.Removing– Fold the seat cushion forwards completely. – Press the wire clamps in the direction of the arrow
fig. 55
and remove the seat
cushion from its holder.
AB
Fig. 54 Rear seats: Inserting head restraints in the seat cushions Fig. 55 Removing seat cushions
s3j8.a.book Page 62 Tuesday, April 20, 2010 1:10 PM

Seats and Storage
65
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
Caution
Do not place any objects with sharp edges in the nets - risk of net damage.Folding hooks*Folding hooks for attaching small items of lu
ggage, such as bags etc., are provided on
both sides of the luggage compartment
fig. 58
.
An item of luggage weighing up to
10 kg can be attached to the hook.
WARNING
Please refer to the following guidelines
page 63.
Luggage compartment cover You can use the luggage compartment cover behind the head restraints for storing
light and soft items.
Fig. 59 Remove / install the luggage compartment coverThe luggage compartment cover can be remo
ved as required if one must transport
bulky goods. – Unhook the support straps
fig. 59
.
– Remove the luggage compartment cover from the holders with adequate
blows to the bottom side of the cove
r in the area between the holders.
– To re-install, place the cover on the cont
act surfaces of the side trim panel and
position the mounts on the cover above
the holders at the side trim panel.
– Interlock the cover with adequate blows to
the top side of the cover in the area
between the holders.
– Attach the support straps on the boot lid. The luggage compartment cover is foreseen for
storage of small objects of up to 2.5 kg.
in weight.
WARNING
No objects should be placed on the
luggage compartment cover, the vehicle
occupants could be endangered if th
ere is sudden braking or the vehicle
collides with something.
Fig. 58 Luggage compartment: folding hook (Fabia)
A1
A2
A3
A2
A1
s3j8.a.book Page 65 Tuesday, April 20, 2010 1:10 PM

Seats and Storage
66
Caution
When closing the boot lid, jamming and da
mage to the luggage compartment cover or
the side trim panel can occur
if handled in an unprofessional way. Therefore, check the
following before closing:
The mounts of the cover must be interlocked on the holders of the side trim
panel .
The items which are transported must not exceed the level of the luggage compart-
ment cover.
The cover must not be jammed in the seal of
the boot lid when it is in the opened
position.
There must be no object in the gap between the opened cover and the rear seat
backrest.
Please ensure that the heating elements
of the rear window heater are not
damaged as a result of objects placed in this area.
Note
When opening the boot lid, lift the luggage compartment cover - risk that objects placed in this area can slip forward!Further positions of the luggage compartment cover You can use the luggage compartment cover behind the head restraints for storing light and soft items.Fig. 60 Luggage compartment cover in the lowe
r position / stowed behind the rear seats
The luggage compartment cover can also be
put into the lower position on the
supporting elements
fig. 60
- left.
The luggage compartment cover can also
be stowed behind the rear seats
fig. 60
-
right.Foldable luggage compartment cover (Combi)Fig. 61 Luggage compartment: Foldable luggage
compartment cover / removing the foldable
luggage compartment coverPulling out– Pull the foldable luggage compartment cover in direction of arrow as far as the
stop into the secured position
fig. 61
.
Folding– Press the cover in the handle area in di
rection of arrow , the cover rolls up auto-
matically.
Removing– Have the foldable luggage compartment cover removed to transport bulky goods
by pressing on the side of
the cross rod in direction of arrow and taking it out
by moving it in direction of arrow
fig. 61
.
A3
A2
A1
A2
A3
A4
s3j8.a.book Page 66 Tuesday, April 20, 2010 1:10 PM

Seats and Storage
67
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
WARNING
No objects should be placed on the luggage compartment cover, the vehicle occupants could be endangered if th
ere is sudden braking or the vehicle
collides with something.
Caution
Please ensure that the heating elements of the rear window heater and the foldable luggage compartment cover are not damaged as
a result of objects transported in this
area.Variable loading floor in the luggage compartment* (Combi)Remove variable loading floorFig. 62 Luggage compartment: Fold up variable loading floor / removeThe variable loading floor makes it easier to handle bulky goods and creates an even luggage compartment floor when the rear seats are folded forward. The maximum permissable surface load of the variable loading floor is 75 kg.Removing the variable loading floor– Unlock the variable loading floor by turning the locking bolts by approx. 180° to
the left
fig. 62
.
– You can fold together the variable loading
floor by moving it in the direction of the
arrow.
– Lift up the variable loading floor in direction of arrow
fig. 62
and take out the
loading floor by pulling in direction of arrow
fig. 62
.
Installing the variable loading floor– Place the variable loading floor once
folded together onto the carrier rails.
– Fold open the variable loading floor.– Lock the variabble loading floor by turning the locking bolts by approx. 180° to
the right.
WARNING
Pay attention when installing that the ca
rrier rails and the va
riable loading floor
are correctly fixed, otherwis
e the occupants are at risk.
Note
If the variable loading floor* is installed
page 67 in the luggage compartment, no
flexible storage compartment or fixing net*
page 64 can be installed.
Remove carrier railsFig. 63 Luggage compartment: Slacken
check points / remove carrier rails
AA
A1
A2
AA
s3j8.a.book Page 67 Tuesday, April 20, 2010 1:10 PM

Seats and Storage
68 Remove carrier rails– Slacken the check points on the carrier rails using the vehicle key or a flat screw-
driver
page 67, fig. 63
.
– Grasp the carrier rail
at the position
page 67, fig. 63
and slacken it by
pulling in the direction of the arrow.
You can take out the removable storage
compartments* in order to facilitate the removal
page 78, “Removeable storage
compartments* in the luggage compartment”.
– Grasp the carrier rail at the position ,
slacken it by pulling in the direction of
the arrow and take it out.
– The carrier rail on the other side of
the luggage compartment can be removed in
the same way.
Install carrier rails– Position the carrier rails on the
sides of the luggage compartment.
– Press both check points on each carrier rail up to the stop.– Check the attachment of the
carrier rails by pulling it.
WARNING
Pay attention when installing that the ca
rrier rails and the variable loading floor
are correctly fixed, otherwise
the occupants are at risk.
Divide the luggage compartment with variable loading floor*
The luggage compartment can be divided with the variable loading floor. – Lift up the part with the holder and se
cure it by sliding it into the grooves
 fig. 64
.
Net partition* (Combi)Use the net partition behind the rear seatsFig. 65 Pull out the net partition / roll upPulling out– Open the right rear door. – Fold down the rear seat backrests slightly forwards, which makes it possible to clear
the access for unrolling the net partition.
– Pull the net partition at the bracket out of the housing in direction of the
holders
fig. 65
.
– Insert the cross rod into one of the mounts .– Insert the other end of the cross rod by pressing into the second mount.– Press both ends of the cross rod
forward into the function position.
– Then push the seat backrest back into th
e upright position until the locking button
clicks into place - check by pulling on the seat backrest

.
AB
AA
A1
AA
A2
Fig. 64 Divide the luggage compart- ment
AA
AB
AC
AC
s3j8.a.book Page 68 Tuesday, April 20, 2010 1:10 PM