2010 Seat Alhambra bulb

Contents 4
Engine oil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Engine coolant . . . . . . . . . . . . . . . . . . . . . . . . . . .
Vehicle battery . . . . . . . . . . . . . . . . . . . . . . . . . . .
Wheels and tyres . . . . . . . . . . . . . . . . . . . . . . . . .
Wheels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Wheel trims* . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Changing a wheel* . . . . . . . . . . . . . . . . . . . . . . .
If and when . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
In case of emergency . . . . . . . . . . . . . . . . . . . . .
Emergency locking and unlocking . . . . . . . . . . .
Tools* . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fuses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Changing bulbs . . . . . . . . . . . . . . . . . . . . . . . . . .
Starting assistance . . . . . . . . . . . . . . . . . . . . . . .
Towing and tow starting . . . . . . . . . . . . . . . . . . .
Technical Data. . . . . . . . . . . . . . . . . . . . . . .
General notes on the technical data . . . . . . .
Outstanding information . . . . . . . . . . . . . . . . . .
Data on fuel consumption . . . . . . . . . . . . . . . . .
Towing a trailer . . . . . . . . . . . . . . . . . . . . . . . . . .
Wheels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Te ch n ica l D ata. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Checking fluid levels . . . . . . . . . . . . . . . . . . . . . .
Petrol engine 1.4 110 kW (150 PS) . . . . . . . . . .
Diesel engine 2.0 TDI 100 kW (135 PS) . . . . . . .
Diesel engine 2.0 TDI 100 kW (135 PS)
Automatic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Diesel engine 2.0 TDI 103 kW (140 PS) . . . . . . .
Diesel engine 2.0 TDI 103 kW (140 PS)
Automatic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Dimensions and capacities . . . . . . . . . . . . . . . .
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 309
313
318
323
323
336
339
345
345
348
353
356
360
371
375
379
379
379
381
382
382
383
383
384
385
387
388
390
392
393

Lights and visibility113
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a
Lights and visibility
Lights
Introduction
The legal requirements regarding the use of vehicle lights in each country
must be observed.
The driver is personally responsible for the correct use and adjustment of the
lights in all situations.
Additional information and warnings:
xSEAT information system Ÿpage 70
xChanging bulbs Ÿpage 360
WARNING
If the headlights are set too high and the main beam is not used correctly,
there is a risk of dazzling or distracting other road users. This could result
in serious accident.
xAlways make sure that the headlamps are correctly adjusted.
xNever use the main beam or flashed headlamps as this could dazzle
other drivers.

Lights and visibility 114
Warning lamps
Several warning and control lamps should light up for a few seconds when
the ignition is switched. This signals that the lamp is working properly. They
will switch off after a few seconds.
WARNING
If the warning lamps and messages are ignored, the vehicle may stall in
traffic, or may cause accidents and severe injuries.
xNever ignore the warning lamps or text messages.
xStop the vehicle safely as soon as possible.
xPark the vehicle at a suitable distance away from the traffic ensuring
that the exhaust system is not in contact with inflammable material, for
example, dry grass, fuel, oil, etc.
xA faulty vehicle represents a risk of accident for the driver and for other
road users. If necessary, switch on the hazard warning lamps and put out
the warning triangle to advise other drivers.
Caution
Failure to heed the warning lamps and text messages when they appear may
result in faults in the vehicle.
lights upPossible causeSolution

Driving light totally or partially
faulty.
Replace the corresponding
bulb Ÿpage 360.
If all the bulbs are OK, the vehi-
cle should be taken to a spe-
cialised workshop if necessary.
Fault in adaptive light.Ÿpage 118.

Rear fog light switched on.
Ÿpage 116.
Fog lights switched on

Left or right turn signal.
The warning lamp flashes twice
as fast when a vehicle or trailer
turn signal is faulty.If necessary, check the vehicle
and trailer lighting.
Headlight on or flasher on.Ÿpage 115.
+Headlight adjustment (Light
Assist) on.Ÿpage 117.
flashesPossible causeSolution
Fault in the adaptive light sys-
tem.Contact a specialist workshop
Ÿpage 117.

Checking and refilling levels 296
Closing the tank cap
xScrew on the tank cap clockwise until it you hear it click into position.
xPress the tank flap until you hear it click into place. The tank flap must be
flush with the body contour.
WARNING
Do not continue refilling once the fuel nozzle has switched itself off. The
fuel tank may be filled too much. As a result, fuel may spurt out and spill.
This could lead to a fire, explosion and severe injuries.
Caution
xAlways remove any fuel spilled on the vehicle paintwork immediately to
avoid damage to the wheel housing, the tyre and vehicle paintwork.
For the sake of the environment
Spilt fuel can contaminate the environment.
Refilling precautions
Information on bulb replacement Ÿpage 360.
Checklist
Never work on the engine or in the engine compartment if you are not familiar
with the operations to be carried out, the applicable safety standards and
especially if you do not have the instruments, liquids and tools necessary
Ÿpage 304, “Working in the engine compartment”! Have the work carried
out by a qualified workshop if you are uncertain. Check the following regu-
larly, preferably when you refuel:
xWindscreen washer fluid level Ÿpage 124
xEngine oil level Ÿpage 309
xEngine coolant level Ÿpage 313
xBrake fluid level Ÿpage 210
xTyre pressure Ÿpage 323
xVehicle lighting required to guarantee road safety:
–Indicators
– Side lights, dipped headlights and full beam headlights
– Rear lights
–Brake lights
– Rear fog light Ÿpage 116
WARNING
Not following the checklist prepared for your own safety could lead to acci-
dents and severe injuries.
xAlways follow the check list and perform the necessary operations.

If and when 360
Changing bulbs
Introduction
Changing bulbs requires a certain amount of manual skill. If you are unsure,
SEAT recommends that you consult an qualified workshop or request assist-
ance from a specialist. In general, a specialist is required if other vehicle
components must be removed or if the discharge lamps must be replaced.
You should store spare light bulbs in the vehicle for safety-relevant lights.
Spare bulbs may be obtained from the Official dealers and workshops. In
some countries, it is a legal requirement to carry spare bulbs in the vehicle.
Driving with faults and blown bulbs on the vehicle exterior lighting is against
the law.
Additional bulb specifications
The specifications of some headlamp bulbs and bulbs for the tail lamps fitted
at the factory may be different to those of conventional bulbs. Bulb informa-
tion is displayed on the bulb socket or on the bulb itself.
Additional information and warnings:
xLights and visibility Ÿpage 113
xWorking in the engine compartment Ÿpage 304
xVehicle tools Ÿpage 353
xFuses Ÿpage 356
WARNING
If the road is not well-lit and the vehicle is not clearly visible to other
drivers, there is a risk of accident.
WARNING
Failure to replace bulbs correctly may cause serious accidents.
xBefore carrying out any work in the engine compartment please read
and observe the warnings Ÿpage 304. In any vehicle, the engine compart-
ment is a hazardous area and could cause severe injury.
xDischarge lamps work with high-voltage and can cause serious or fatal
injury if handled incorrectly.
xH7 and discharge lamps are highly pressurised and could explode
when being changed.
xOnly replace the bulbs concerned when they have cooled.
xNever replace bulbs alone if you are not familiar with the operations
necessary. If you are not sure about procedures then visit a qualified work-
shop to carry out the necessary work.
xNever touch the bulb glass directly. Fingerprints will be evaporated by
the heat of the operating bulb thus “fogging” up the reflector.
xThe headlamp frameworks in the engine compartment and the tail
lamps contain sharp elements. Always protect your hands when changing
bulbs.
Caution
After changing a bulb, if the rubber covers and plastic caps are not replaced
correctly on the headlamp framework, the electrical installation may be
damaged, especially if water is allowed to enter.

If and when361
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a
Indicator
Several warning and control lamps should light up for a few seconds when
the ignition is switched. This signals that the lamp is working properly. They
will switch off after a few seconds.
Checking the bulbs of a trailer
For vehicles with the factory fitted trailer system, certain trailer lights are also
controlled if the socket is correctly connected.
A fault on a trailer turn indicator is indicated on the instrument panel by the
indicator blinking twice as fast (
 or
) Ÿpage 113.
xGeneral fault of all indicators on one side.
xFault in one tail light (on some models, also the registration light).
xFault in two brake lights.
WARNING
If the warning lamps and messages are ignored, the vehicle may stall in
traffic, or may cause accidents and severe injuries.
xNever ignore the warning lamps or text messages.
xStop the vehicle safely as soon as possible.
Caution
Failure to heed the warning lamps and text messages when they appear may
result in faults in the vehicle.
Note
A fault in the LED on the tail lights will not be indicated. However, if the fault
affects all the LEDs then this will be indicated by the indicator .
Information for replacing bulbs
Checklist
To replace a bulb, carry out the following operations always in the order given
Ÿ:
1. Park the vehicle a safe distance from traffic and on suitable ground.
2. Connect the electronic parking brake Ÿpage 210.
3. Turn the light switch to position 0 Ÿpage 113.
4. Move the gear lever into the neutral position Ÿpage 113.
5. Automatic gearbox: Move selector lever to position P Ÿpage 201.
6. Stop the engine and remove the key from the ignition Ÿpage 195.
7. Manual gearbox: Select a gear Ÿpage 201.
8. Wait until all of the passenger compartment lights are turned off
Ÿpage 113.
9. Allow the corresponding bulb to cool.
10. Visually inspect fuses to see if any are blown Ÿpage 356.
11. Replace the bulb according to the instructions Ÿ. Bulbs should only
be replaced by new identical models. Bulb information is displayed on
the bulb socket or on the bulb itself.
12. In general, never touch the bulb glass directly. The heat of the bulb would
cause the fingerprint to evaporate and condense on the reflector. This
will impair the brightness of the headlight.
lights upPossible causeSolution
A vehicle exterior lighting
bulb is not working.Replace the faulty bulb.

If and when 362
13. Check if the new bulb is working. If the bulb is not working, it may not
have been correctly fitted, it could be damaged or the connector may not
be correctly connected.
14. Every time a bulb for the headlights is replaced, visit a specialised work-
shop to check the headlights.
WARNING
Failure to follow the checklist prepared for your own safety could lead to
accidents and severe injuries.
xAlways complete the operations given in the checklist and observe the
general rules of safety.
Caution
Always remove and fit headlights carefully to avoid damage to the paintwork
and other vehicle parts.
To replace halogen headlight bulbs
There is no need to remove the headlight to replace bulbs.
Complete operations only in the sequence given:
WARNING (continued)
Fig. 213 In the engine
compartment: Left-hand
side headlight lining.
dipped beam headlights,
daytime lights and
main beam headlights
and side lights.
AA
ABAC
Fig. 214 Left headlight

If and when363
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a
Note
The images show the left hand headlight from behind. The structure of the
right hand side headlight is symmetric.
page 362, fig. 213,
page 362, fig. 214 Indicators (small lamp
holder)Dipped beam head-
lightsDaylight driving lightsMain beam headlightsSide lights
1.Always take the checklist into account and take the necessary actions Ÿpage 361.
2.Open the bonnet ’ Ÿpage 304.
3.Remove the rubber cover on the rear of the headlight.
4.
Rotate the lamp holder
to the left all the way
and pull it out back-
wards with the bulb.
Rotate the lamp holder to the left all the way and
pull it out backwards with the bulb.
Press the wire clip down-
wards and pull the lamp
holder out with the
bulb.Pull the lamp holder
out backwards with the
bulb.
5.Depending on the model, the bulb is removed directly from the lamp holder or it may need to be rotated and then removed.
6.Replace the faulty bulb by a new identical bulb.
7.Place the bulb holder in the headlight and rotate to the right all the way.
Place the lamp holder in
the headlight and pull the
wire clip upwards until it
clicks into place.Place the lamp holder in
the headlight and insert
completely.
8.Insert the rubber cover.
AAABAC
A1A2
A3