Page 365 of 413

If and when 364
To replace the xenon headlights bulb
There is no need to remove the headlight to replace bulbs.
Complete operations only in the sequence given:Always seek the help of a specialist when changing the Xenon dipped beam
and full beam headlamps Ÿ in “Introduction” on page 360.
Note
The illustrations show the left hand headlight. The structure of the right hand
side headlight is symmetric.
Fig. 215 In the engine
compartment: Turn signal
cover.
Fig. 216 Turn signal indi-
cator lamp holder and
turning light .A1A2
Turn signal indicators Turning lights
1.Always take the checklist into account and take the necessary
actions Ÿpage 361.
2.Open the bonnet ’ Ÿpage 304.
3.Rotate the cover Ÿfig. 215 in the direction of the arrow and remove
it.
4.
Rotate the lamp holder
Ÿfig. 216 to the left all the way
and pull it out backwards with the
bulb.Press the wire clip downwards
and pull the lamp holder
Ÿfig. 216 out with the bulb.
5.Depending on the model, the bulb is removed directly from the lamp
holder or it may need to be rotated and then removed.
6.Replace the faulty bulb by a new identical bulb.
7.Place the bulb holder in the head-
light and rotate to the right all the
way.Place the lamp holder in the
headlight and pull the wire clip
upwards until it clicks into place.
8.Rotate the cover Ÿfig. 215 in the opposite direction to the arrow as
far as it will go.
A1A2
A1
A2
Page 366 of 413

If and when365
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a
To replace the front bumper bulbs
Complete operations only in the sequence given:
Fig. 217 On the right-
hand side of the front
bumper: Removing the
headlights
Fig. 218 Changing the
bulbs in the headlights.
1.Always take the checklist into account and take the necessary
actions Ÿpage 361.
2.Pull the cover forwards, in the direction of the arrow Ÿfig. 217.
3.Unscrew the attachment screw Ÿfig. 217 using the screwdriver
from the on-board tools Ÿpage 353.
4.Tilt the headlight slightly forward and extract it from its lateral
attachments Ÿfig. 218 (small arrows).
5.Release the connector Ÿfig. 218 and remove it.
6.Rotate the lamp holder Ÿfig. 218 to the left all the way, in the
direction of the arrow, and pull it out backwards with the bulb.
7.Replace the faulty bulb by a new identical bulb.
8.Place the bulb holder in the headlight and rotate to the right all the
way.
9.Insert the connector Ÿfig. 218 on the lamp holder Ÿfig. 218
. The connector must audibly click into place.
10.Place the headlight into its position Ÿfig. 218 (small arrows) and
tilt it backwards.
11.Tighten the attachment screw Ÿfig. 217 using the screwdriver.
12.Replace the cover on the bumper Ÿfig. 217.
A1
A1
A2
A1
A2
A1
Page 367 of 413
If and when 366
To replace the tailgate light bulbs
Complete operations only in the sequence given:
Fig. 219 On the boot lid:
Remove the cover.
Fig. 220 On the boot lid:
Remove the lamp holder.
1.Always take the checklist into account and take the necessary
actions Ÿpage 361.
2.Open the tailgate Ÿpage 97.
3.Extract the cover carefully using the flat part of the screwdriver as a
lever ( Ÿpage 354, fig. 207) on the indent Ÿfig. 219 .
4.Release the lamp holder connector by pulling on the red connector
block.
5.Press on the attachment tabs in the direction of the arrow
Ÿfig. 220 and pull out the lamp holder.
6.Replace the faulty bulb by a new identical bulb.
7.Install the lamp holder. The attachment tabs should audibly click
into place.
8.Insert the cover. The cover should lock into place.
A1
Page 368 of 413
If and when367
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a
To replace the tail light bulbs
Complete operations only in the sequence given.Removing the tail light units
Complete operations only in the sequence given:
Fig. 221 On the side of the luggage compartment: To
remove the left and right hand side tail lights. remove
the cap; attachment screw.A1A2
Fig. 222 Tail lights on
bodywork: To remove the
lamp holder. to :
Attachment tab.
A1A4
Rear light, leftRear light, right
1.Always take the checklist into account and take the necessary
actions Ÿpage 361.
2.Open the tailgate Ÿpage 97.
3.Open the storage compartments
on the left-hand side of the lug-
gage compartment Ÿpage 162.Move the 12 V socket support by
pressing gently downwards
Ÿfig. 221 (arrow).
4.Rotate the cap Ÿfig. 221 90°
in the direction of the arrow and
remove it.
AB
A1
Page 369 of 413