2010 Seat Alhambra Owner's Manual

Wheels and tyres 336
Wheel trims*
Introduction
Additional information and warnings:
xCaring for and cleaning the vehicle exterior Ÿpage 269
xChange wheel Ÿpage 339
xVehicle tools Ÿpage 353
WARNING
If the wheel trims are not appropriate or not fitted correctly, they could
cause major accidents or damage.
xIncorrectly mounted wheel trims may come off while driving and
endanger other road users.
xDamaged trims must never be mounted on the wheels.
xAlways ensure that the brake ventilation and cooling is not cut off or
blocked. This is also valid if hubcaps are fitted later. If there is not enough
air, you may require significantly longer braking distances.
Caution
Remove and remount wheel trims taking care to avoid damage to the
vehicle.
Hubcaps
Depending upon the version, the hubcap is removed by pulling it Ÿfig. 186,
or by unscrewing it Ÿfig. 187.
Fig. 186 Removing the
hub cap.
Fig. 187 Remove the
hubcap by turning it
outwards.

Wheels and tyres337
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a Vehicles with removable hubcaps
xTo remove the hubcap, take the wire hook from the vehicle tool kit and
hook it through an opening on the trim Ÿpage 336, fig. 186.
xRemove the trim by pulling it in the direction of the arrow.
xTo replace the hubcap, press the hubcap against the rim until it clicks into
place.
Vehicles with screw-on hubcaps
xTo remove, turn the hubcap to the right or to the left until it comes off the
rim Ÿpage 336, fig. 187.
xHold it from behind by a rib and pull the trim.
xTo re pl a ce, centrally align the trim on the wheel.
xPress the trim against the wheel rim until it clicks into place.
Full hubcaps*
Removing the full hubcap
xTake the wheel brace and the wire hook from the vehicle tool kit
Ÿpage 353.
xHook the wire through one of the grooves on the hubcap.
xInsert the wheel brace onto the wire hook Ÿfig. 188 and pull the hub cap
in the direction shown by the arrow.
Fitting hubcaps
Before mounting the full hubcap, the anti-theft wheel lock must be threaded
into position Ÿpage 340, fig. 191 or . Otherwise it will not be
possible to mount the full hubcap.
Press the hubcap against the wheel so that the space for the valve fits over
the tyre valve Ÿpage 340, fig. 191 . Make sure that the hubcap is
correctly fitted all the way around the wheel.
Wheel bolt caps
Fig. 188 Removing the
full hubcap.
A2A3
A1
Fig. 189 Removing the
wheel bolt caps

Wheels and tyres 338
xTake the wire hook from the vehicle tool kit Ÿpage 353.
xInsert the wire hook in the cap through the opening Ÿpage 337, fig. 189
and pull outwards in the direction of the arrow.
The caps protect the wheel bolts and should be remounted after changing the
tyre.
The anti-theft wheel locking bolt has a special cap. This cap only fits on anti-
theft locking bolts and is not for use with standard wheel bolts.

Wheels and tyres339
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a
Changing a wheel*
Introduction
The tyres mounted on the vehicle are anti-puncture. The wheels should only
be changed when switching from summer to winter tyres or vice-versa. The
tools required for changing a wheel are only supplied with the vehicle if the
vehicle is supplied from the factory with winter tyres. If this is not the case,
please take the vehicle to a specialised workshop to have the wheels
changed.
You should only change the wheels yourself if the vehicle is parked in a safe
place, you are familiar with the procedure and you have all the necessary
tools! Otherwise, you should seek professional assistance.
Additional information and warnings:
xVehicle key set Ÿpage 78
xWheels and tyres Ÿpage 323
xWheel trims Ÿpage 336
xVehicle tools Ÿpage 353
WARNING
Changing a wheel can be dangerous, especially on the hard shoulder.
Please observe the following rules to minimise the risk of injury:
xStop the vehicle safely as soon as possible. Park your vehicle as safe
distance from surrounding traffic to change a wheel.
xWhen changing a wheel, keep all passengers and particularly children
a safe distance away from the work area.
xTurn on the hazard warning lights to warn other road users.
xEnsure the ground on which you park is flat and solid. If necessary,
support the jack on a wide solid base.
xIf you are changing a wheel yourself, you should be familiar with the
required procedure. Otherwise, you should seek professional assistance.
xOnly use suitable tools that are not damaged when changing a wheel.
xAlways stop the engine, turn on the electronic parking brake and place
the gear selector lever in position P, for an automatic gearbox, or engage a
gear for a manual gearbox to reduce the risk of the vehicle moving acciden-
tally.
xHave the tightening torque of the wheel bolts checked as soon as
possible with a reliable torque wrench.
Preparations for changing a wheel
Check list
Before changing a wheel, complete the following operations in the order
given Ÿ:
1. Park the vehicle on an even and solid surface.
2. Connect the electronic parking brake Ÿpage 210.
3. Automatic gearbox: Move selector lever to position P Ÿpage 201.
4. Stop the engine and remove the key from the ignition Ÿpage 195.
5. Manual gearbox: Select a gear Ÿpage 201.
6. Have all vehicle occupants get out of the vehicle and wait in a safe place
(for example, behind the safety barrier).
7. Block the opposite wheel with two folding wedges taken from the vehicle
tool kit Ÿpage 354, fig. 208 or similar objects.
8. When towing a trailer: unhook the trailer from the towing vehicle and
park it correctly.
9. If the luggage compartment is full: take the baggage out of the vehicle.
WARNING (continued)

Wheels and tyres 340
10. Take the vehicle tool kit out of the luggage compartment.
11. Remove the wheel trims Ÿpage 336.
WARNING
Failure to follow the checklist prepared for your own safety could lead to
accidents and severe injuries.
xAlways complete the operations given in the checklist and observe the
general rules of safety.
Wheel bolts
Only use the tool supplied with the vehicle to loosen the wheel bolts.
Loosen the wheel bolts only about one turn before raising the vehicle with the
jack.
If the wheel bolt is very tight, you may be able to loosen it by pushing down
on the end of the wheel brace carefully with your foot. Hold on to the car for
support and take care not to slip.
Loosening wheel bolts
xFit the wheel brace as far as it will go over the wheel bolt Ÿfig. 190.
xHold the wheel brace at the end and rotate the bolt approximately one
turn anticlockwise Ÿ.
Loosening anti-theft wheel bolts
For wheels with full hubcap, the anti-theft wheel lock must be threaded into
position Ÿfig. 191 or before mounting the hubcap. Otherwise it will
not be possible to mount the full hubcap.
xTake the adapter for anti-theft wheel bolts out of the vehicle tool kit.
xInsert the adapter onto the wheel bolt.
Fig. 190 Changing the
wheel: Slacken the wheel
bolts.
Fig. 191 Changing the
wheel: Tyre valve and
position of anti-theft
wheel locking bolt or
.A1
A2A3
A2A3

Wheels and tyres341
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a
xFit the wheel brace onto the adapter as far as possible.
xHold the wheel brace at the end and rotate the bolt approximately one
turn anticlockwise Ÿ.
Important information about wheel bolts
The wheel rims and bolts have been designed to be fitted to factory options.
If different rims are fitted, the correct wheel bolts with the right length and
correctly shaped bolt heads must be used. This ensures that wheels are fitted
securely and that the brake system functions correctly.
In some circumstances, wheel bolts from the same model vehicle should not
be used.
Wheel bolt tightening torque
The prescribed tightening torque for wheel bolts for steel and alloy wheels is
140 Nm. Have the tightening torque of the wheel bolts checked as soon as
possible with a reliable torque wrench.
If wheel bolts are rusty and it is difficult to tighten them, the threads should
be replaced and cleaned before checking the torque.
Never grease or lubricate wheel bolts or the wheel hub threads. Although
they have been tightened to the prescribed torque, they could come loose
while driving.
WARNING
If the wheel bolts are not fitted correctly they could be released while
driving leading to loss of vehicle control and serious damage.
xOnly use wheel bolts which correspond to the wheel rims in question.
xNever use different wheel bolts.
xThe bolts and threads should be clean, free of oil and grease and easy
to thread.
xTo loosen and tighten the wheel bolts, always use the wheel brace
supplied with the vehicle.
xLoosen the wheel bolts only about one turn before raising the vehicle
with the jack.
xNever grease or lubricate wheel bolts or the wheel hub threads.
Although they have been tightened to the prescribed torque, they could
come loose while driving.
xNever loosen the bolted joints of wheel rims with bolted ring trims.
xIf the wheel bolts are not tightened to the correct torque, they may
come loose while driving, and the bolts and rims may come out. If the tight-
ening torque is too high, the wheel bolts and threads can be damaged.
WARNING (continued)

Wheels and tyres 342
Raising the vehicle with the jack
The jack may be applied only at the jacking points shown (marks on chassis)
Ÿfig. 192. The mark indicates the jacking points below the vehicle. The jacking points are on the ribs behind the front edges Ÿfig. 193. Always the
relevant jacking point for the wheel to be changed Ÿ.
Fig. 192 Jack position
points
Fig. 193 : jack mounted on the left front part of the
vehicle : jack mounted on the left rear part of the
vehicle.AAAB

Wheels and tyres343
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a Raise the vehicle using only the designated jacking points.
Check list
For your own safety and that of other passengers, the following points should
be observed in the order given Ÿ:
1. Select a suitable flat and firm surface for raising the vehicle.
2. Switch off the engine, engage a gear (manual gearbox) or place the
selector lever in position P Ÿpage 201 and turn on the electronic
parking brake Ÿpage 210.
3. When towing a trailer: unhook the trailer from the towing vehicle and
park it correctly.
4. Loosen the wheel bolts on the wheel to be changed Ÿpage 340.
5. Look below the vehicle for the jacking point Ÿpage 342, fig. 192
closest to the tyre which has to be changed.
6. Raise the jack with the handle until it can be inserted below the jacking
point.
7. Ensure that the foot of the jack is firmly on the ground and that it is
placed immediately below the lifting point on the vehicle Ÿpage 342,
fig. 193.
8. Straighten the jack and continue raising it using the handle until the claw
holds the vertical reinforcement beneath the vehicle Ÿpage 342,
fig. 193.
9. Raise the vehicle until the wheel is clear of the ground.
WARNING
If the vehicle is not correctly raised, it could fall off the jack causing serious
injury. Please observe the following rules to minimise the risk of injury:
xYou should only use a jack approved by SEAT for your vehicle. Other
jacks, even those approved for other SEAT models, might slip out of place.
xThe ground should be firm and flat. If the ground is sloped or soft then
the vehicle could slip and fall off the jack. If necessary, support the jack on
a wide solid base.
xIf the ground is slippery (for example, on tiles), place a non-slip surface
(for example a floor mat) beneath the jack to avoid slipping.
xOnly fit the jack at the prescribed jacking points. The claw of the jack
should grip the reinforcement nerve on the underbody Ÿpage 342,
fig. 193.
xYou should never have any limbs beneath a raised vehicle which is only
supported by a jack.
xIf you have to work underneath the vehicle, you must use suitable
stands additionally to support the vehicle, there is a risk of accident!.
xNever raise the vehicle if it is tilting to one side or the engine is running.
xNever start the engine when the vehicle is raised. The vehicle may come
loose from the jack due to the engine vibrations.
WARNING
Failure to follow the checklist prepared for your own safety could lead to
accidents and severe injuries.
xAlways complete the operations given in the checklist and observe the
general rules of safety.
WARNING (continued)