2010 Seat Alhambra park assist

Trailer towing265
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a
xAs of the combined vehicle and trailer mass, braking distances will be
greater.
xSelect a low gear before driving down a steep hill to use the engine
braking effect to slow down the vehicle. Otherwise, the braking system could
overheat and fail.
xThe vehicle centre of gravity and handling change because of the trailer
load and because of the increased combined mass of the vehicle and trailer.
xIf the towing vehicle is empty and the trailer loaded then the load distri-
bution is incorrect. If you must travel in these conditions, drive carefully and
reduce your speed accordingly.
Hill starts with a trailer
Depending on the hill and the gross combined weight, it is possible that the
combined vehicle and trailer move backwards slightly when starting.
For a hill start with a trailer, proceed as follows:
xPress and hold the brake pedal.
xPress the button once to turn off the electric parking brake
Ÿpage 210.
xPress and hold the button to hold the vehicle and trailer combination
using the parking brake.
xWith a manual gearbox: press the clutch pedal to the floor.
xEngage first gear or the gear range D Ÿpage 201, “Changing gear”.
xRelease the brake pedal.
xMove off slowly. To do this, gently release the clutch pedal (for manual
gearbox).
xRelease the button only when the engine provides sufficient power to
move the vehicle and trailer combination.
WARNING
Jerking the trailer in an unsuitable manner could cause loss of vehicle
control with the subsequent serious consequences.
xDriving with a trailer and transporting heavy or a large objects will
change the vehicle handling and braking distances.
xAnticipate traffic and be extremely cautious. Brake early.
xAdjust your speed and driving style to visibility, road, traffic and
weather conditions. Reduce your speed, especially on steep hills.
xAccelerate gently and carefully. Avoid brusque manoeuvres and sudden
braking.
xAlways take the following precautions seriously. Reduce your speed
immediately if you observe the trailer rocking from side to side.
xNever try to stop the “snaking” by increasing speed.
xAlways take the speed limits for vehicles with and without trailers in
each country into account.
Stabilising the vehicle and trailer combination
Stabilisation of the vehicle and trailer combination is an extension of the
electronic stability programme (ESP) and helps, with the assistance of the
trajectory control, to reduce trailer “snaking”.
Stabilisation of the vehicle and trailer combination is active when the ESP
«
indicator on the dashboard remains lit for about two seconds more than the
ABS indicator.
Requirements for stabilising the vehicle/trailer combination
xAn original tow hitch is fitted by the manufacturer or a compatible model
is retrofitted.
xThe ESP is on. The warning indicator in the control panel « is not lit.
xThe trailer is connected to the vehicle using the socket.
xThe vehicle is driven faster than 60 km/h.
G
G
G
WARNING (continued)

Checking and refilling levels 318
Vehicle batter y
Introduction
The battery is a component of the vehicle's electrical system.
Never work on the electrical system without fully understanding the opera-
tions required, the applicable safety standards and without the correct tools
Ÿ! Have the work carried out by a qualified workshop if you are uncertain.
SEAT recommends visiting a qualified workshop. Negligent work can cause
serious injury.
Location and number of batteries in the vehicle
The battery is located in the engine compartment.
Explanation of the warning indications on the vehicle's battery
Additional information and warnings:
xŸBooklet “Maintenance Programme”
xStarter assist systems (Start-Stop function) Ÿpage 221
xWorking in the engine compartment Ÿpage 304
xAccessories, parts replacement, repairs and modifications Ÿpage 285
WARNING
Working on the vehicle battery and the electrical system can cause corro-
sion, fire and electric shocks. Always read and take into account the
following warnings and safety standards before carrying out any work:
xBefore working on the battery, switch off the engine, the ignition and
all electrical devices then disconnect the negative connection on the
battery.
xKeep children away from acid and the battery itself!
xWear eye protection.
xBattery acid is very corrosive and caustic. It can burn skin and cause
blindness. When handling the battery, protect yourself from splashes of
acids, above all your hands, arms and face.
xDo not smoke and never work close to places exposed to flames or
sparks.
xAvoid sparks and electrostatic discharges when working with cables
and electrical devices.
xNever short the battery terminals.
xNever use a damaged battery. It can explode. Replace a damaged
battery immediately.
xReplaced damaged or frozen batteries as soon as possible. A flat
battery can freeze at temperatures around 0°C (+32 °F).
xVehicles with the battery in the luggage compartment: Ensure that the
battery ventilation hose is correctly secured.
Caution
xNever disconnect the battery if the ignition is switched on or if the engine
is running. This could damage the electrical system or electronic compo-
nents.
SymbolMeaning
Wear eye protection!
Battery acid is very corrosive and caustic. Always wear
protective gloves and eye protection!
ŽFires, sparks, naked lights and smoking are prohibited.
ŸA highly explosive mixture of gases is released when the
battery is under charge.
Keep children away from acid and batteries!

Checking and refilling levels321
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a Start-Stop systems Ÿpage 223 are equipped with a special battery. There-
fore, it must only be replaced with a battery of the same specifications.
Disconnecting the vehicle's battery
If you must disconnect the battery from the electrical system, please note the
following:
xSwitch off the ignition and all electrical equipment.
xThe vehicle must be unlocked before disconnecting the battery, otherwise
the alarm will be triggered.
xFirst disconnect the negative cable and then the positive Ÿ.
Connecting the vehicle's battery
xBefore reconnecting the battery, switch off the engine, the ignition and
electric devices.
xFirst reconnect the positive cable and then the negative Ÿ.
Different control lamps may light up after connecting the battery and
switching the ignition on. They will be turned off after a short trip at a speed
of between 15 - 20 km/h (10 - 12 mph). If the warning indicators remain lit,
please visit a specialised workshop to have the vehicle checked.
If the battery has been disconnected for a long time, it is possible that the
next service date is not displayed or calculated correctly Ÿpage 64. Respect
the maximum service intervals permitted ŸBooklet “Maintenance
Programme”.
Vehicles with the KESSY system (Ÿpage 86): If, after connecting the battery,
the ignition cannot be switched on, lock and unlock the vehicle from outside.
Then try to switch the ignition back on. If the ignition can still not be switched
on, request the assistance of a specialist workshop.
Automatic consumer disconnection
The intelligent vehicle electrical system automatically implements a range of
measures to prevent the battery from discharging when high demands are
made on it:
xthe idling speed is increased so that the alternator provides more elec-
tricity.
xwhere necessary, the power of the most powerful consumers is reduced
or even completely disconnected.
xOn starting the engine, the power supply from the 12-volt sockets and the
cigarette lighter may be interrupted for a short time.
The on-board management program cannot always prevent the battery from
running flat. For example, if the ignition is left on for a long period with the
engine off or if the side lights or parking lights are left on while the vehicle is
stationary.
Why does the battery run flat?
xWhen stationary for a long time without starting the engine, particularly if
the ignition is switched on.
xUse of electrical consumers with the engine switched off.
xIf the auxiliary heater is running Ÿpage 187.
WARNING
Incorrectly securing the battery or using the wrong battery can cause
short-circuits, fire and serious injuries.
xAlways use only maintenance free batteries that do not run flat alone
and whose properties, specifications and size correspond to the standard
battery. The specifications are indicated on the battery case.
WARNING
A highly explosive mixture of gases is released when the battery is under
charge.
xThe batteries should be charged in a well-ventilated room only.
xNever charge a frozen or recently thawed battery. A flat battery can
freeze at temperatures around 0°C (+32 °F).

Wheels and tyres323
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a
Wheels and tyres
Wheels
Introduction
SEAT recommend that all work on tyres and wheels is carried out by a quali-
fied workshop. They have the necessary special tools and replacement parts,
trained personnel and facilities for disposing of the old tyres. SEAT recom-
mends visiting a qualified workshop.
Additional information and warnings:
xTransporting Ÿpage 13
xTo wi ng m o d e Ÿpage 260
xBraking, stopping and parking Ÿpage 210
xPark assist system Ÿpage 229
xTyre control systems Ÿpage 245
xCaring for and cleaning the vehicle exterior Ÿpage 269
xWheel trims Ÿpage 336
xChange wheel Ÿpage 339
xNotes for the user Ÿpage 283
WARNING
The vehicle cannot be totally controlled or braked if the tyres (new or used)
are worn or damaged.
xIncorrect use of wheels and tyres could make driving more dangerous
and result in serious accidents and damage.
xAll four wheels must be fitted with radial tyres of the same type, size
(rolling circumference) and the same tread pattern.
xNew tyres do not give maximum grip and will not have reached their
maximum braking capacity to start with, and therefore need running in. To
prevent accidents and major damage, extreme caution should be taken for
the first 600 km (370 miles).
xCheck tyre pressures regularly and ensure they are maintained at the
pressures indicated. If the tyre pressure is too low, the tyres could over-
heat, resulting in tread detachment or even burst tyres.
xNever drive on damaged (punctured, cut, cracked or dented) or worn
tyres. Driving on damaged or worn tyres could result in burst tyres, serious
accidents or damage. Worn or damaged tyres must be replaced immedi-
ately.
xNever exceed the maximum permitted speed or loads specified for the
type of tyre fitted on your vehicle.
xThe efficiency of driver and brake assist systems also depends on the
grip of the tyres.
xIf you notice unusual vibration or if the vehicle pulls to one side when
driving, stop the car immediately and check the tyres and wheels for
damage.
xTo minimise the risk of losing control of the vehicle or causing a serious
accident, never undo the bolted joints of beadlock wheels.
xNever mount used tyres or wheels if you are not sure of their previous
history. They may be damaged, although the damage is not immediately
visible.
xOld tyres, even if they have never been used, may lose air or burst unex-
pectedly while driving, resulting in serious accident or damage. If tyres are
over six years old, they should only be used in an emergency and with
extreme caution.
WARNING (continued)

Wheels and tyres339
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a
Changing a wheel*
Introduction
The tyres mounted on the vehicle are anti-puncture. The wheels should only
be changed when switching from summer to winter tyres or vice-versa. The
tools required for changing a wheel are only supplied with the vehicle if the
vehicle is supplied from the factory with winter tyres. If this is not the case,
please take the vehicle to a specialised workshop to have the wheels
changed.
You should only change the wheels yourself if the vehicle is parked in a safe
place, you are familiar with the procedure and you have all the necessary
tools! Otherwise, you should seek professional assistance.
Additional information and warnings:
xVehicle key set Ÿpage 78
xWheels and tyres Ÿpage 323
xWheel trims Ÿpage 336
xVehicle tools Ÿpage 353
WARNING
Changing a wheel can be dangerous, especially on the hard shoulder.
Please observe the following rules to minimise the risk of injury:
xStop the vehicle safely as soon as possible. Park your vehicle as safe
distance from surrounding traffic to change a wheel.
xWhen changing a wheel, keep all passengers and particularly children
a safe distance away from the work area.
xTurn on the hazard warning lights to warn other road users.
xEnsure the ground on which you park is flat and solid. If necessary,
support the jack on a wide solid base.
xIf you are changing a wheel yourself, you should be familiar with the
required procedure. Otherwise, you should seek professional assistance.
xOnly use suitable tools that are not damaged when changing a wheel.
xAlways stop the engine, turn on the electronic parking brake and place
the gear selector lever in position P, for an automatic gearbox, or engage a
gear for a manual gearbox to reduce the risk of the vehicle moving acciden-
tally.
xHave the tightening torque of the wheel bolts checked as soon as
possible with a reliable torque wrench.
Preparations for changing a wheel
Check list
Before changing a wheel, complete the following operations in the order
given Ÿ:
1. Park the vehicle on an even and solid surface.
2. Connect the electronic parking brake Ÿpage 210.
3. Automatic gearbox: Move selector lever to position P Ÿpage 201.
4. Stop the engine and remove the key from the ignition Ÿpage 195.
5. Manual gearbox: Select a gear Ÿpage 201.
6. Have all vehicle occupants get out of the vehicle and wait in a safe place
(for example, behind the safety barrier).
7. Block the opposite wheel with two folding wedges taken from the vehicle
tool kit Ÿpage 354, fig. 208 or similar objects.
8. When towing a trailer: unhook the trailer from the towing vehicle and
park it correctly.
9. If the luggage compartment is full: take the baggage out of the vehicle.
WARNING (continued)

If and when371
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a
Starting assistance
Introduction
If the engine fails to start because of a discharged battery, the battery of
another vehicle can be used to start the engine. Before starting, check the
magic eye on the battery Ÿpage 318.
For starting assistance, jump lead cables conforming to the standard DIN
72553 are required (see the cable manufacturer instructions). The jump lead
cable must be at least 25 mm
2 in section (0.038 inches2) for petrol engines,
and 35 mm2 (0.054 inches2) for diesel engines.
For vehicles whose battery is not in the engine compartment, the jump leads
should only be connected to the starting assistance connection points in the
engine compartment.
Additional information and warnings:
xStarter assist systems (Start-Stop function) Ÿpage 221
xWorking in the engine compartment Ÿpage 304
xSelective Catalytic Reduction (AdBlue) Ÿpage 300
xVehicle battery Ÿpage 318
WARNING
Incorrect use of jump leads and incorrectly jump starting could cause the
battery to explode resulting in serious injury. Please observe the following
rules to minimise the risk of a battery explosion:
xAll work involving the vehicle battery and electrical system can cause
corrosion, fire and serious electric shocks. Always read and take into
account the safety warnings and standards before beginning work on the
battery Ÿpage 318, “Vehicle battery”.
xThe battery providing current must have the same voltage (12V) and
approximately the same capacity (see markings on battery) as the flat
battery.
xNever charge a frozen or recently thawed battery. A flat battery can
freeze at temperatures around 0°C (+32 °F).
xIf a battery is frozen and/or has been frozen then it must be replaced.
xA highly explosive mixture of gases is released when the battery is
being charged. Always keep lit cigarettes, open flames, sparks and fire far
from the battery. Never use a mobile telephone when connecting and
removing the jump leads.
xCharge the battery only in well ventilated areas given that when the
battery is charged by outside assistance, it creates a mix of highly explo-
sive gases.
xJump leads should never enter into contact with moving parts in the
engine compartment.
xNever switch the positive and negative poles or connect the jump leads
incorrectly.
xNote the instructions provided by the manufacturer of the jump leads.
Caution
To avoid considerable damage to the vehicle electrical system, note the
following carefully:
xIf the jump leads are incorrectly connected, this could result in a short
circuit.
xThe vehicles must not touch each other, otherwise electricity could flow as
soon as the positive terminals are connected.
WARNING (continued)

If and when 374
xThe non-insulated parts of the battery clamps must not be allowed to
touch. Also, the cable connected to the positive pole of the battery should
never enter into contact with electrically conductive parts of the vehicle.
xCheck the magic eye on the battery; use a lamp if necessary. If it is clear
yellow or clear, do not start the vehicle: obtain specialist technical assist-
ance.
xAvoid static electricity discharges in the area around the battery. In the
event of sparks, explosive gases coming from the battery could ignite.
xNever use starting assistance if the vehicle battery is damaged, frozen
or has been frozen.
WARNING (continued)

If and when 378
xScrew in the tow ring into its position anticlockwise as far as it will go
Ÿ. Use a suitable tool to firmly tighten the tow ring in its location.
xAfter towing, remove the tow ring by turning it clockwise and put the cover
back in place.
Caution
xThe tow ring must always be completely and firmly tightened. Otherwise,
it could be released while towing and tow-starting.
xVehicles with a factory fitted towing device, can only be used for towing
with a tow-bar, specially designed to fit on a tow hitch ball. Otherwise, the tow
hitch ball and the vehicle may be damaged. Otherwise, a tow rope should be
used.
Towing advice
Towing requires some experience, especially when using a tow-rope. Both
drivers should be familiar with the technique required for towing. For this
reason, inexperienced drivers should abstain.
While driving, avoid excessive traction forces and jerking. When towing on an
unpaved road, there is always a risk of overloading and damaging the
anchorage points.
If the vehicle is towed, with the hazard warning lights on and the ignition
switched on, the turn signal may be used to indicate changes of direction.
Simply operate the turn indicator lever as usual. Meanwhile, the hazard
warning lights will go off. When the turn signal lever is returned to the rest
position, the hazard warning lights will be turned on automatically.
Notes for the driver of the towed vehicle
xLeave the ignition on to avoid locking the steering wheel, to release the
electronic parking brake and to activate the turn signal indicators, the horn
as well as the window wipers and window washers.
xAs the power assisted steering does not work if the engine is not running,
you will need more strength to steer than normally.
xThe brake must be depressed must harder as the brake servo does not
operate. Avoid hitting the towing vehicle.
xNote the instructions and information contained in the instruction manual
for the vehicle to be towed.
Notes for the driver of the towing vehicle
xAccelerate gently and carefully. Avoid sudden manoeuvres.
xBrake well in advance than usual and brake gently.
xNote the instructions and information contained in the instruction manual
for the vehicle to be towed.