2010 Seat Alhambra park assist

Driving211
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a
Warning and control lamps
lights upPossible cause ŸSolution
H (red)
Together with the control
lamp
G on the button: Elec-
tronic parking brake on.Ÿpage 212
Fault in the brake system› Stop the vehicle!
Seek professional assistance!
Ÿpage 215.
Brake fluid level inadequate.› Do not drive on!
Check brake fluid level
Ÿpage 219.
Together with the ABS control
lamp
J: ABS fault.
Contact a specialist workshop.
The vehicle can be braked with-
out ABS.
K (red)Brake pedal not pressed!Press brake pedal to the floor.
I (yel-
low)Front brake pads worn.
Contact a specialist workshop
immediately. Inspect all the
brake pads and replace as nec-
essary.
« (yel-
low)
ESP disconnected by system.Switching the ignition on and off
If necessary, drive for a short
distance.
Fault in ESP.Contact a specialist workshop.
Together with the ABS control
lamp
J: Fault in ABS.
Contact a specialist workshop.
The vehicle can be braked with-
out ABS.
The battery has been recon-
nected.Ÿpage 318
l (yel-
low)TCS manually deactivated.
To turn on the TCS Ÿpage 218.
TCS is automatically activated
when the ignition is switched on
or off.
J (yel-
low)
Together with the ESP control
lamp
«: Fault in ABS.Contact a specialist workshop.
The vehicle can be braked with-
out ABS.
Together with the warning
lamp
H or : ABS fault.
 (yel-
low)Together with the warning
lamp
H flashing: Electronic
parking brake faulty.Contact a specialist workshop.
K
(green)Brake pedal not pressed.
Press the brake pedal to select a
gear ratio.
Press the brake pedal to discon-
nect the electronic parking
brake Ÿpage 212.
flashesPossible cause ŸSolution
H (red)
Electronic parking brake
faulty. The control lamp

may light up at the same time
or the control lamp
G may
flash on the button.
Contact a specialised workshop,
as it may not be possible to park
the vehicle in safety.
« (yel-
low)ESP or TCS adjusting.Take your foot off the accelera-
tor. Adjust your driving style to
the road conditions.
lights upPossible cause ŸSolution

Driving 212
Several warning and control lamps should light up for a few seconds when
the ignition is switched. This signals that the lamp is working properly. They
will switch off after a few seconds.
WARNING
If the warning lamps and messages are ignored, the vehicle may stall in
traffic, or may cause accidents and severe injuries.
xNever ignore the warning lamps or text messages.
xStop the vehicle safely as soon as possible.
WARNING
Driving with brakes in bad condition could result in a serious accident.
xIf the brake warning lamp H does not go out, or if it lights up when
driving, the brake fluid level in the reservoir is too low or there is a fault in
the brake system. Obtain professional assistance immediately
Ÿpage 219, “Brake fluid”.
xIf the brake warning lamp H lights up together with the ABS warning
lamp J, the regulation function of the ABS could be malfunctioning. As a
result, the rear wheels can lock relatively easily when braking. If the rear
wheels lock this could result in loss of vehicle control! If possible, reduce
your speed and drive carefully to a specialist workshop close by to check
the brake system. During the following journey, avoid sudden braking and
manoeuvres.
xIf the ABS warning lamp J does not go out or if it lights while driving,
the ABS is malfunctioning. The vehicle can only be stopped using normal
braking without ABS. The protection provided by the ABS is not available.
Visit a specialised workshop as soon as possible.
xIf I lights, alone or accompanied by a warning message on the instru-
ment panel screen, please go immediately to a specialist workshop to
check the brake pads and to replace them if they are worn.
Caution
Failure to heed the warning lamps and text messages when they appear may
result in faults in the vehicle.
Electronic parking brake
Applying the electronic parking brake
The parking brake can be applied whenever the vehicle is at a standstill, even
when the ignition is switched off. Always apply the parking brake when you
leave your vehicle and when you park.
xPull button until the control lamp G on the button lights up.
xThe parking brake is applied when the control lamp H lights up on the
instrument panel Ÿpage 211.
Releasing the electronic parking brake
xSwitch the ignition on.
Fig. 143 Detailed view of
the centre console: elec-
tronic parking brake
switch
G

Driving221
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a
Start assist systems
Introduction
Additional information and warnings:
xSEAT information system Ÿpage 70
xBraking, stopping and parking Ÿpage 210
xVehicle battery Ÿpage 318
xWheels and tyres Ÿpage 323
xAccessories, parts replacement, repairs and modifications Ÿpage 285
xJump starting Ÿpage 371
WARNING
The intelligent technology in the start assist systems cannot change the
laws of physics. The improved comfort provided by start assist systems
should not prompt you to take risks.
xUnintentional movements of the vehicle could cause serious injury.
xThe start assist systems are not a replacement for driver awareness.
xAlways try to adapt the speed of the vehicle and your style of driving to
the condition of the ground or the road and to weather and traffic condi-
tions.
xThe start assist system cannot keep the vehicle stationary in all condi-
tions on a gradient or cause it to brake on steep downhill gradients, e.g. if
the road is slippery or icy.

Driving 224
Important conditions for the engine to automatically switch off
xThe driver seat belt must be buckled.
xThe driver door must be closed.
xThe bonnet must be closed.
xThe factory-fitted towing bracket must not be electrically connected to a
trailer.
xA minimum engine temperature has been reached.
xThe vehicle has moved since the last stop.
xIn vehicles with Climatronic: The temperature inside the vehicle is within
the preset temperature range.
xThe temperature set is neither very high nor very low.
xThe air conditioning defrost function is not switched on.
xIn vehicles with Climatronic: the blower has not been manually set to a
high speed.
xThe power level of the vehicle's battery is sufficient.
xThe vehicle's battery temperature is neither too high nor too low.
xThe vehicle is not on a steep gradient or slope.
xThe front wheels are not overly turned.
xThe heated windscreen is not switched on.
xReverse gear is not engaged.
xThe park assist system is not switched on.
Conditions for automatically restarting the engine
The engine may automatically restart under the following conditions:
xIf the vehicle interior is too hot or too cold.
xIf the vehicle moves.
xIf the vehicle's battery voltage drops.
Conditions requiring the key to restart the engine
The engine must be started using the key under the following conditions:
xIf the driver unbuckles his/her seat belt.
xIf the driver's door is opened.
xIf the bonnet is opened.
xIn vehicles with a manual gearbox: If a gear has been selected.
Switching Start-Stop mode on and off manually
xPress the button on the centre console Ÿpage 223, fig. 147.
xThe button will light up when the Start-Stop function is switched off.
The engine will start immediately if the vehicle is in Stop mode when it is
switched off manually.
WARNING
The brake servo and the power steering do not work when the engine is
switched off.
xNever allow the vehicle to move when the engine is switched off.
Caution
Using the Start-Stop function for a long period at very high outdoor tempera-
tures could damage the vehicle's battery.
Note
In some cases, you may have to restart the vehicle using the key. Observe the
corresponding message on the instrument panel display.
›

Driving225
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a
Parking sensor system
Introduction
The parking sensor system assists the driver when parking. When the vehicle
approaches an obstacle, forwards or backwards, an intermittent sound will
be heard, higher or lower depending on the distance. The shorter the
distance, the shorter the intervals between tones. If the vehicle is too close to
the obstacle, the sound signal becomes constant.
If you continue to approach an obstacle when the sound is continuous, this
means the system can no longer measure the distance.
The sensor system on the bumpers transmit and receive ultrasound. Using
the ultrasound signal (transmission, reflection from the obstacle and recep-
tion), this system continuously calculates the distance between the bumper
and the obstacle.
Additional information and warnings:
xPark Assist system Ÿpage 229
xAccessories, parts replacement, repairs and modifications Ÿpage 285
WARNING
The parking sensor system and the optical parking system cannot replace
driver awareness.
xThe sensors have blind spots in which obstacles and people are not
registered.
xAlways observe the area around the vehicle, as the sensors do not
always detect small children, animals or objects.
xThe surface of certain objects and some clothing do not reflect the
ultrasound signals from the parking distance system. The system cannot
detect or incorrectly detects these objects and people wearing these types
of clothes.
xExternal sound sources can affect the parking distance aid signals. In
this case, under certain circumstances, people and objects will not be
detected.
Caution
xThe sensors may not always be able to detect objects such as trailer draw
bars, thin rails, fences, posts, trees and open boots, etc. This could result in
damage to your car.
xAlthough the parking sensor system detects and warns of the presence of
an obstacle, the obstacle could disappear from the angle of measurement of
the sensors if it is too high or low and the system would no longer indicate it.
Therefore, it will not warn you of these objects. Ignoring the warnings of the
parking sensor system could cause considerable damage to the vehicle.
xThe bumper sensors may become damaged or misaligned, for example,
when parking.
xTo ensure that the system works properly, the bumper sensors must be
kept clean, free of ice and snow and uncovered.
xWhen cleaning the sensors with high-pressure or steam cleaning equip-
ment, spray the sensors briefly at a distance of no less than 10 cm (4 inches).
Note
Acoustic sources may lead to erroneous warnings on the parking sensor
system, e.g. rough tarmac, cobbles or the noise of other vehicles.
WARNING (continued)

Driving 226
Parking sensor system*
The parking sensor system assists the driver when parking. If the vehicle is
approaching an obstacle, an intermittent sound signal is emitted. The shorter the distance, the shorter the intervals between tones. If the vehicle is too
close to the obstacle, the sound signal becomes constant.
Switching the parking sensor system on and off
xPress the button Ÿfig. 148 when the ignition is switched on.
xAutomatic on: select reverse gear.
xAutomatic off: drive faster than 15 km/h.
The button lights up when the function is switched on.
Things to note regarding the parking sensor system
xThe parking sensor system sometimes registers water on the sensors as
an obstacle.
xIf the distance does not change, the warning signal will sound less loudly
after a few seconds. If the continuous signal sounds, the volume will remain
constant.
xWhen the vehicle moves away from the obstacle, the beeping sound auto-
matically switches off. On approaching the obstacle again, the beeping
sound will automatically switch back on.
xIf the electronic parking brake is engaged or the gear lever is set to P, no
sound will be emitted.
xYour Authorised Service Centre can adjust the volume of the warning
signals.
Note
If the parking sensor system is faulty, a constant acoustic signal will be
emitted the first time it is switched on and the button will flash. Switch the
parking sensor system off using the button and take the vehicle to a
specialist workshop to have the system checked as soon as possible.
Fig. 148 Detailed view of
the centre console: button
for switching the parking
sensor system on and off.
Fig. 149 Parking sensor
system sensors on the
front bumper.
'

Driving227
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a
Optical parking system* (OPS)
The optical parking system is an accessory to the Parking sensor system
Ÿpage 226 and the park assist system Ÿpage 229.The zone recorded by the sensors in front of and behind the vehicle is
displayed on the factory-fitted radio or navigation system screen. Any obsta-
cles are display in relation to the vehicle Ÿ.
Zones explored
The zone in which obstacles are recognised runs to a distance of around 120
cm from the front of the vehicle and up to 60 cm to the side Ÿfig. 151 .
Behind the vehicle, the zone analysed reaches a distance of up to 160 cm and
around 60 cm to the sides Ÿfig. 150 .
Screen display
The image displayed represents the supervised zones in several segments.
As the vehicle moves closer to an obstacle, the segment moves closer to the
vehicle displayed Ÿfig. 150 and Ÿfig. 151 . When the penultimate
segment is displayed, this means that the vehicle has reached the collision
zone. Stop the vehicle!
Fig. 150 On-screen OPS
display: an obstacle
has been detected in the
collision zone. an
obstacle has been
detected in the segment.
zone recorded behind
the vehicle.AA
AB
AC
Fig. 151 On-screen OPS
display: an obstacle
has been detected in the
segment. zone
recorded behind the
vehicle.AA
AB
FunctionNecessary operations
Switching the display
on:Switch on the parking sensor system Ÿpage 226
or the park assist system Ÿpage 229. The OPS
switches on automatically.
Switching the display
off manually:
Press a zone selection button on the factory-fitted
radio or navigation system
OR: Briefly press the function button or
on the screen.
Switching the display
off manually:Drive forwards at more than about 10-15 km/h.
Select the reverse gear on vehicles with rear
assist Ÿpage 234. The display changes to the
image of the camera.
ERVC
AB
AC
ABAA

Driving229
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a
Park Assist system*
Introduction
The Park Assist system helps the driver to find a suitable place to park, to
insert the vehicle into parallel and perpendicular parking places and to leave
parallel parking places.
The Park Assist system is limited to the system abilities and requires that the
driver is especially attentive Ÿ.
The parking sensor system is a component of the Park Assist system that
helps to park the vehicle.
For vehicles with the optical parking system, the radio navigation systems
screen displays the detected zones in front of and behind the vehicle, indi-
cating - within the limits of the system - the position of obstacles compared
to the vehicle.
The park assist system cannot be switched on if the factory-fitted towing
bracket is electrically connected to a trailer.
Additional information and warnings:
xBraking, stopping and parking Ÿpage 210
xParking sensor system Ÿpage 225
xCaring for and cleaning the vehicle exterior Ÿpage 269
xAccessories, parts replacement, repairs and modifications Ÿpage 285
WARNING
Despite the assistance provided by the park assist system, do not run any
risks when parking. The system is not a replacement for driver awareness.
xUnintentional movements of the vehicle could cause serious injury.
xAdjust your speed and driving style to visibility, road, traffic and
weather conditions.
xThe surface of certain objects and items of clothing and external sound
sources may have a negative affect on the park assist signals or on the
system sensors or may not reflect its signals.
xThe sensors have blind spots in which obstacles and people are not
registered.
xAlways observe the area around the vehicle, as the sensors do not
always detect small children, animals or objects.
Caution
xThe park assist system aims exclusively at other parked vehicles, without
taking curbs or other circumstances into account. Make sure you do not
damage the tyres and wheel rims when parking. Where necessary, stop
manoeuvring to avoid damaging the vehicle.
xThe sensors may not always be able to detect objects such as trailer draw
bars, thin rails, fences, posts and trees, etc. This could result in damage to
your car.
xAlthough the parking sensor system detects and warns of the presence of
an obstacle, the obstacle could disappear from the angle of measurement of
the sensors if it is too high or low and the system would no longer indicate it.
Therefore, it will not warn you of these objects. Ignoring the warnings of the
parking sensor system could cause considerable damage to the vehicle. This
is also valid when using the park assist (e.g. to park behind a truck or motor-
cycle). Therefore, always keep a close watch on the area in front of and behind
the vehicle while parking, and intervene promptly if necessary.
xTo ensure that the system works properly, the bumper sensors must be
kept clean, free of ice and snow and uncovered.
xThe bumper sensors may become damaged or misaligned, for example,
when parking.
WARNING (continued)