2010 Seat Alhambra ABS

Driving 212
Several warning and control lamps should light up for a few seconds when
the ignition is switched. This signals that the lamp is working properly. They
will switch off after a few seconds.
WARNING
If the warning lamps and messages are ignored, the vehicle may stall in
traffic, or may cause accidents and severe injuries.
xNever ignore the warning lamps or text messages.
xStop the vehicle safely as soon as possible.
WARNING
Driving with brakes in bad condition could result in a serious accident.
xIf the brake warning lamp H does not go out, or if it lights up when
driving, the brake fluid level in the reservoir is too low or there is a fault in
the brake system. Obtain professional assistance immediately
Ÿpage 219, “Brake fluid”.
xIf the brake warning lamp H lights up together with the ABS warning
lamp J, the regulation function of the ABS could be malfunctioning. As a
result, the rear wheels can lock relatively easily when braking. If the rear
wheels lock this could result in loss of vehicle control! If possible, reduce
your speed and drive carefully to a specialist workshop close by to check
the brake system. During the following journey, avoid sudden braking and
manoeuvres.
xIf the ABS warning lamp J does not go out or if it lights while driving,
the ABS is malfunctioning. The vehicle can only be stopped using normal
braking without ABS. The protection provided by the ABS is not available.
Visit a specialised workshop as soon as possible.
xIf I lights, alone or accompanied by a warning message on the instru-
ment panel screen, please go immediately to a specialist workshop to
check the brake pads and to replace them if they are worn.
Caution
Failure to heed the warning lamps and text messages when they appear may
result in faults in the vehicle.
Electronic parking brake
Applying the electronic parking brake
The parking brake can be applied whenever the vehicle is at a standstill, even
when the ignition is switched off. Always apply the parking brake when you
leave your vehicle and when you park.
xPull button until the control lamp G on the button lights up.
xThe parking brake is applied when the control lamp H lights up on the
instrument panel Ÿpage 211.
Releasing the electronic parking brake
xSwitch the ignition on.
Fig. 143 Detailed view of
the centre console: elec-
tronic parking brake
switch
G

Driving 216
Caution
xNever make the brakes slip by pressing the pedal gently, if it is not really
necessary to brake. Continuously pressing on the brake pedal will heat the
brakes. This could significantly reduce braking power, increase braking
distance or even result in the total failure of the brake system.
xReduce speed, move down a gear or select a shorter range of gears before
long steep slopes. This allows you to use the engine braking effect and to
reduce the strain on the brake system. Otherwise, the brakes may overheat
and fail. Only use the brakes to reduce speed or to stop.
Note
When checking the front brake pads, take the time to also check the rear
brake pads. The thickness of the brake pads should be checked visually and
regularly, by looking through the openings in the wheel rims or from under-
neath the vehicle. If necessary, remove the wheels to check them thoroughly.
SEAT recommends visiting a qualified workshop.
Assisted braking systems
The assisted braking systems ESP, ABS, BAS, TCS and EDS only operate when
the ignition is switched on. They contribute significantly to increasing active
safety.
Electronic stability programme (ESP)
ESP reduces the risk of skidding and increases the vehicle stability by braking
individual wheels under specific driving conditions. ESP detects critical
handling situations, such as understeer, oversteer and wheelspin on the
driven wheels. The system stabilises the vehicle by braking individual wheels
or by reducing the engine torque.
The ESP has limits. It is important to realise that the ESP is also subject to the
laws of physics. ESP will not be able to deal with all situations with which drivers may be faced. For example, if the road surface changes suddenly then
ESP will not be useful in all cases. If the vehicle suddenly enters a section
covered by water, mud or snow then ESP will not provide assistance in the
same way as on dry ground. If the vehicle loses its grip on the ground and
moves on a film of water (aquaplaning), the ESP will not be able to assist the
driver to control the vehicle due to the loss of adherence with the road surface
preventing braking and steering. If the vehicle is driven through series of
bends at high speed, the ESP will not always be as effective: the vehicle reac-
tion to aggressive driving is not the same as at reduced speeds. When driving
with a trailer, ESP does not provide the same amount of vehicle control as
without a trailer.
Adjust your speed and driving style to road, traffic and weather conditions.
ESP cannot push the limits of the laws of physics; improve the transmission
available or maintain the vehicle on the road if a lack of driver attention
creates an inevitable situation. Otherwise, ESP assists in maintaining vehicle
control in extreme situations and uses the movements of the steering made
by the driver to maintain the vehicle moving in the desired direction. If the
vehicle is driven at such a speed that it will leave the road before ESP can
intervene then the system cannot provide assistance.
The ABS, BAS, TCS and EDS systems are incorporated into the ESP. The ESP is
always on. The ESP should only be turned off using the TCS button
Ÿpage 218, fig. 144 when traction is insufficient. Always remember to turn
on the TCS once more when the vehicle has traction once again.
Anti-lock brake system (ABS)
ABS can prevent the wheels from locking during braking until just before the
vehicle stops thus helping the driver to steer the vehicle and maintain
control. This means that, even during full braking, the risk of skidding is
reduced:
xPress and hold the brake pedal fully. Do not remove your foot from the
brake pedal or reduce braking force!
xDo not “pump” the brake pedal, or reduce braking force!
xMaintain vehicle direction when braking fully.

Driving217
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a
xWhen the brake pedal is released or when the brake force is reduced, ABS
is turned off.
ABS control can be observed by vibration of the brake pedal and noise. You
should never expect the ABS to reduce the braking distance under any
circumstances. Braking distances will increase when driving on gravel, recent
snow or on icy and slippery ground.
When driving on loose ground, the all-terrain configuration of the ABS is auto-
matically turned on. When ABS is activated, the front wheels may lock briefly.
This shortens the braking distance in off-road situations as the wheels are
prevented from digging into loose surfaces. All-terrain ABS only intervenes
when driving in a straight line. When the front wheels are turned, the normal
ABS is activated.
Braking assist system (BAS)
The brake assist system may reduce the required braking distance. The brake
assist system boosts the braking force if you press the brake pedal quickly in
an emergency. As a result, the braking pressure increases rapidly, the braking
force is multiplied and the braking distance is reduced. This enables the ABS
to be activated more quickly and efficiently.
¡Do not lift your foot off the brake pedal! When the brake pedal is released or
when the brake force is reduced, braking assist automatically turns off the
brake servo.
Traction control when accelerating (TCS)
In the event of wheelspin, the traction control system reduces the engine
torque to match the amount of grip available. The TCS makes some situations
easier, for example, when starting, accelerating or going uphill, even in unfa-
vourable road conditions.
The TCS can be switched on or off manually Ÿpage 218.
Electronic differential lock system (EDS)
EDS is available when driving in straight lines under normal conditions. When
the EDL detects wheelspin, it brakes the spinning wheel and directs the power to the other driven wheels. To prevent the disc brake of the braked
wheel from overheating, the EDL cuts out automatically if subjected to exces-
sive loads. The EDL will switch on again automatically when the brake has
cooled down.
WARNING
Driving at high speed on icy, slippery wet ground can result in loss of
vehicle control and serious injury to the driver and passengers.
xAdjust your speed and driving style to visibility, road, traffic and
weather conditions. Even though the braking assist systems, ABS, BAS,
EDS, TCS and ESP, provide more security, do not take unnecessary risks
while driving.
xBraking assist systems can not overcome the laws of physics. Even with
ESP and other systems, slippery and wet roads will always be dangerous.
xDriving to quickly on wet ground can result in the wheels losing contact
with the ground in an effect known as aquaplaning. Without adherence, it
is impossible to brake, steer or control the vehicle.
xBraking assist systems cannot avoid accidents if, for example, the
driver does not respect safety distances or drives to quickly in difficult
conditions.
xEven though braking assist systems are extremely effective and help
control the vehicle in difficult situations, remember that the vehicle
stability depends on tyre grip.
xWhen accelerating on a slippery surface, for example on ice and snow,
press the accelerator carefully. The wheels can still slip even with braking
assist systems resulting in loss of vehicle control.
WARNING
The effectiveness of the ESP can be considerably reduced if other compo-
nents and systems affecting driving dynamics are not maintained or are not

Driving 218
functioning correctly. This includes, among others, brakes, tyres and other
systems already mentioned.
xRemember that changing and fitting other components to the vehicle
can affect operation of the ABS, BAS, ASL EDL and ESP.
xChanges to the vehicle suspension or using unapproved wheel/tyre
combinations can affect operation of the ABS, BAS, ASL EDL and ESP and
their effectiveness.
xLikewise, the effectiveness of ESP depends on the use of suitable tyres
Ÿpage 323.
Note
To ensure that the ESP and TCS work properly, all four wheels must be fitted
with identical tyres. Any differences in the rolling radius of the tyres can cause
the system to reduce engine power when this is not desired.
Note
If a malfunction should occur in the ABS, the ESP, TCS and EDS will also be
affected.
Note
Noises may be heard while any of the above systems are operating.
Turning on and off the TCS
The electronic stabilisation programme (ESP) includes the ABS, EDL and TCS
systems and only works when the engine is running.
The TCS can be switched off while the engine is running by pressing the
Ÿfig. 144 button. The TCS (and similar) is only switched off when the
required traction is not obtained:
xWhen driving through deep snow or on loose ground (gravel...).
xWhen freeing a trapped vehicle.
Turn the TCS back on by pressing the button Ÿfig. 144.
WARNING (continued)
Fig. 144 Detailed view of
the centre console: button
used to switch TCS on and
off (vehicles with ESP).
« OFF
« OFF

Driving219
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a
Brake fluid
In the course of time, the brake fluid absorbs water from the ambient air. If
there is too much water contained in the brake fluid, the brake system could
be damaged. In addition, the boiling point of the brake fluid is significantly
lowered. When the brake fluid contains too much water and the brakes are
subject to considerable forces, bubbles of water vapour can form in the
system. These bubbles of water vapour can significantly reduce braking
power, notably increasing braking distance, and could even result in the total
failure of the brake system. Ensuring that the brake system is always func-
tioning correctly is essential for your own safety and the safety of other road
users Ÿ.
Brake fluid specifications
SEAT have developed a special brake fluid optimised for the brake systems of
their vehicles. To ensure the optimum working of the brake system, SEAT
recommends the use of brake fluid in accordance with the VW 501 14
standard. If this brake fluid is not available or another brake fluid is used for
different reasons, use a brake fluid that complies with the United States standard FMVSS 116 DOT 4 or the German standard DIN ISO 4925 CLASS 4
Ÿ.
Brake fluids conforming to the standard VW 501 14, fulfil the American
requirements of the FMVSS 116 DOT 4 standard and the German DIN ISO
4925 CLASS 4 standard. However, fluids that comply with the American
FMVSS 116 DOT 4 standard or the German DIN ISO 4925 CLASS 4 standard do
not necessarily comply with the VW 501 14 standard. Always check the infor-
mation on the brake fluid container and ensure that you are using suitable
brake fluid.
A suitable brake fluid can be obtained from Authorised Service Centres.
Brake fluid level
The level of the brake fluid should always be between the MIN and MAX
marks, or above the MIN mark Ÿ.
It is not always possible to check the level of the brake fluid, as in some
models the engine components make it difficult to see the brake fluid reser-
voir. If you cannot read the exact brake fluid level, consult a specialist.
The brake fluid level drops slightly when the vehicle is being used due to wear
of the brake pads and the automatic readjustment of the brake.
Changing the brake fluid
The brake fluid should be changed in accordance with the instructions given
in the Maintenance Programme. Have the brake fluid changed by a qualified
workshop. SEAT recommends visiting a qualified workshop. This means that
only brake fluid complying with the required specifications will be used.
WARNING
If the brake fluid level is low or unsuitable/old brake fluid is used, the brake
system may fail or braking power will be reduced.
xCheck the brake system and the brake fluid level regularly!
xThe brake fluid should be changed regularly in accordance with the
instructions given in the Maintenance Programme.
Fig. 145 In the engine
compartment: brake fluid
reservoir, lid

Driving243
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a
Dynamic chassis control* (DCC)
Introduction
Additional information and warnings:
xAccessories, parts replacement, repairs and modifications Ÿpage 285
WARNING
Switching the dynamic chassis control system on while the vehicle is in
motion could divert your attention from the traffic and cause accidents.
Note
Have the dynamic chassis control checked by a specialist workshop if it does
not work in the way described in this chapter.
Operation and control
The dynamic chassis control continuously adapts the shock absorbers to the
condition of the road and current traffic conditions, according to the set
programme.
Steering is also adapted in the Sport programme.
Programme selection
xSwitch the ignition on.
xPress the button repeatedly until the desired programme is displayed.
ProgrammeRecommended driving situations
Comfort setting (e.g. long distances or on irregular
road surfaces).
Balanced setting (e.g. for day-to-day use).
Sport setting (e.g. for sports driving).
Fig. 160 Detailed view of
the centre console: button
for setting the dynamic
chassis control.
#/-&/24
./2-!,
30/24
Q

Driving 244
The programme is switched on if and do not light up on
the button. The set programme remains selected after the ignition is switched
off.
WARNING
The dynamic features are modified by adjusting the shock absorbers.
Dynamic chassis control must never lead to any kinds of risk.
xAlways try to adapt the speed of the vehicle and your style of driving to
the condition of the ground or the road and to weather and traffic condi-
tions.
Note
In the event of a fault in the dynamic chassis control, and will
flash on the button. Driving comfort may be affected during the fault. Have
the system checked by a specialist workshop.
./2-!,#/-&/2430/24
#/-&/2430/24

Driving245
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a
Tyre monitoring systems
Introduction
The tyre monitor indicator monitors the tyre pressure of each wheel using the
ABS sensors. The ABS sensors monitor the tyre tread perimeter and vibra-
tions of each tire. The tyre monitor indicator warns the driver if it detects a
considerable drop in tyre pressure of one or several tyres while driving. Loss
of tyre pressure will be indicated by the indicator
~ as well as a sound and
sometimes a text message on the screen of the instrument panel. When you
open the driver's door, you will find a label indicating the tyre pressure recom-
mended by the manufacturer for the maximum vehicle load for each tyre
approved for the vehicle in question. By pressing the adjustment button on
the tyre monitoring indicator, you may change the reference pressure for the
tyres so that the tyre pressure to be monitored coincides with actual tyre pres-
sure Ÿpage 248.
Suitable use of the adjustment button Ÿpage 248.
Additional information and warnings:
xTransporting Ÿpage 13
xBraking, stopping and parking Ÿpage 210
xCaring for and cleaning the vehicle exterior Ÿpage 269
xWheels and tyres Ÿpage 323
xAccessories, parts replacement, repairs and modifications Ÿpage 285
WARNING
Unsuitable handling of the wheels and tyres may lead to sudden tyre pres-
sure losses, to tread separation or even to a blow-out.
xCheck tyre pressures regularly and ensure they are maintained at the
pressures indicated. If the tyre pressure is too low, the tyres could over-
heat, resulting in tread detachment or even burst tyres.
xTyre pressure should be that indicated on the label when the tyres are
cold at all times Ÿpage 328.
xRegularly check the cold inflation pressure of the tyres. If necessary,
change the tyre pressure of the vehicle tyres while they are cold.
xRegularly check your tyres for damage and wear.
xNever exceed the maximum permitted speed or loads specified for the
type of tyre fitted on your vehicle.
WARNING
Incorrect use of the tyre monitoring indicator button could result in the
indicator giving erroneous messages or prevented from indicating the
danger caused by a defective tyre Ÿpage 248.
Caution
xThe tyre valves may be damaged if the cap is not in place. Check that the
caps are identical to the standard caps and have been correctly tightened. Do
not use metal caps Ÿpage 248.
xDo not damage the valves when changing the tyres Ÿpage 248.
For the sake of the environment
Under-inflated tyres lead to increased fuel consumption and tyre wear.
Note
Do not only rely on the tyre monitoring system. Regularly check your tyres to
ensure that the tyre pressure is correct and that the tyres are not damaged
due to puncture, cuts, tears and impacts/dents. Remove objects from the
tyres only when the tyres have not been pierced by these.
WARNING (continued)