2010 Peugeot 407 Dag light
[x] Cancel search: lightPage 103 of 249
7SAFETY
88
SEAT BELTS
Detection of fastening of the front
seat belts
When the ignition is switched on , if a
front passenger has not fastened their
seat belt and if the vehicle speed is below
12 mph (20 km/h) , you are warned by
lighting of the seat belt warning lamp .
The warning lamp switches off when
the seat belt(s) concerned is(are) fas-
tened.
If the vehicle speed is above 12 mph
(20 km/h) , y o u a r e w a r n e d b y fl a s h -
ing of the seat belt warning lamp ,
an audible signal and a message on
the multifunction screen identifying the
unfastened seat belt(s).
Front seat belts with
pre-tensioner and force
limiter
In the event of a serious front impact,
the pre-tensioning system instantly
t i g h t e n s t h e s e a t b e l t s fi r m l y a g a i n s t
the bodies of the occupants.
The pre-tensioning seat belts are
armed when the ignition is on.
The force limiter reduces the pressure
of the seat belt against the chest of
the occupant, so increasing his pro-
tection.
Rear seat belts
T h e r e a r s e a t s a r e a l l fi t t e d w i t h a
three-point inertia reel seat belt.
The rear side seat belts have a force
l i m i t e r a n d m a y b e fi t t e d w i t h a p r e -
tensioning inertia reel.
To fasten the seat belts
Pull the strap, then insert the
tongue into the buckle.
Check that the seat belt is secured
correctly by pulling the strap.
To unfasten the seat belts
Press the red button on the buckle. Before folding the seat back, pull the
strap and insert the seat belt tongue
into the buckle. This precaution will
ensure that each seat belt is in place
when the rear seats are lifted again.
Note: a bag or an animal
placed on the front passenger
seat may cause illumination of
the warning lamp.
The audible signal ceases and the
warning lamp switches off when the
seat belt concerned is fastened.
After two minutes without any action
o n t h e s e a t b e l t s , t h e fl a s h i n g w a r n i n g
lamp remains on permanently and the
audible signal ceases. All of the warn-
ings cease when a door is opened or
when the engine is switched off.
Front seat belt height adjustment :
To lower the attachment point,
squeeze control 1 and slide it
downwards.
To raise the attachment point, slide
control 1 upwards.
Page 104 of 249
7SAFETY
89
The driver must ensure that
the passengers use the seat
belts correctly and that they
are all properly restrained be-
fore setting off.
Wherever you are seated in the vehi-
cle, always fasten your seat belt, even
for short journeys.
Do not invert the seat belt buckles as
t h e y w i l l n o t f u l fi l t h e i r r o l e f u l l y .
If the seats have armrests * , the lap
part of the seat belt must always pass
under the armrest.
T h e s e a t b e l t s a r e fi t t e d w i t h a n i n e r t i a
reel permitting automatic adjustment
of the length of the strap to your size.
The seat belt is stored automatically
when not in use.
Before and after use, ensure that the
seat belt is reeled in correctly.
The lower part of the strap must be
positioned as low as possible on the
pelvis.
The upper part must be positioned in
the hollow of the shoulder.
T h e i n e r t i a r e e l s a r e fi t t e d w i t h a n a u -
tomatic locking device which comes
into operation in the event of a colli-
sion, on emergency braking or if the
vehicle rolls over. You can release the
device by pulling rapidly on the strap
and releasing it. Recommendations for children:
- use a suitable child seat if the pas-
senger is less than 12 years old or
s h o r t e r t h a n o n e m e t r e fi f t y ,
- do not use the strap-guide * when a child seat is installed.
- never use the same seat belt to se- cure more than one person,
- never allow a child to travel on your lap.
Depending on the nature and se-
riousness of the impacts , the pre-
tensioning device may be triggered
before and independently of the air
bags. Triggering of the pre-tensioners
is accompanied by a slight emission of
harmless smoke and a noise, due to
the activation of the pyrotechnic car-
tridge incorporated in the system.
In all cases, the airbag warning lamp
comes on.
Following an impact, have the seat
belts system checked, and if necessary
replaced, by a PEUGEOT dealer.
* According to model.
In order to be effective, a seat belt:
- must be tightened as close to the
body as possible,
- must restrain one adult only,
- must not bear any trace of cuts or fraying,
- must be pulled in front of you with a smooth movement, checking that
it does not twist,
- must not be transformed or modi- fi e d t o a v o i d a l t e r i n g i t s p e r f o r -
mance.
In accordance with current safety reg-
ulations, all repairs and checks must
be carried out by a PEUGEOT dealer
who guarantees that the work is car-
ried out correctly.
Have your seat belts checked regularly
by a PEUGEOT dealer and particularly
if the straps show signs of damage.
Clean the seat belt straps with soapy
water or a textile cleaning product,
sold by PEUGEOT dealers.
After folding or moving a seat or rear
bench seat, ensure that the seat belt is
positioned and rolled up correctly.
Page 105 of 249
7SAFETY
AIRBAGS
The airbags have been designed to
maximise the safety of the occupants
(with the exception of the rear centre
passenger) in the event of violent col-
lisions. They supplement the action of
the force-limiting seat belts.
In this case, the electronic detectors
record and analyse the front and side
impacts suffered in the impact detec-
tion zones:
- in the event of a serious impact, the airbags are deployed instanta-
neously and protect the occupants
of the vehicle (with the exception
of the rear centre passenger); im-
mediately after the impact, the air-
b a g s d e fl a t e r a p i d l y s o t h a t t h e y d o
not hinder the visibility of the oc-
cupants or their possible exit from
the vehicle,
- in the event of a minor impact or rear impact and in certain roll-over
conditions, the airbags will not be
deployed; the seat belt alone is
s u f fi c i e n t t o p r o v i d e m a x i m u m p r o -
tection in these situations. Front airbags
The front airbags protect the driver
and front passenger in the event of a
serious front impact in order to limit the
risks of injury to the head and chest.
T h e y a r e fi t t e d i n t h e c e n t r e o f t h e
steering wheel for the driver and in the
dashboard for the front passenger.
Impact detection zones
A. Front impact zone.
B. Side impact zone.
The deployment of one or
more airbags is accompanied
by a slight discharge of harm-
less smoke and a noise, due
to the activation of the pyrotechnic
cartridge incorporated in the system.
This smoke is not harmful, but sensi-
tive individuals may experience some
irritation.
The noise of the detonation may result
in a slight loss of hearing for a short
time. Activation
They are deployed simultaneously, ex-
cept in cases where the passenger's
front airbag is deactivated, in the event
of a serious front impact applied to all
or part of the front impact zone
A , in
the longitudinal centreline of the vehi-
cle on a horizontal plane directed from
the front to the rear of the vehicle.
T h e f r o n t a i r b a g i n fl a t e s b e t w e e n t h e
front occupant of the vehicle and the
dashboard to cushion their forward
movement.
The airbags do not operate
when the ignition is off.
This equipment only operates
once. If a second impact occurs (dur-
ing the same or a subsequent acci-
dent), the airbag will not operate.
Page 106 of 249
7SAFETY
91
Disarming the front
passenger's front air bag * Reactivation
As soon as the child seat is removed,
turn the air bag slot to the
"ON" position
to re-activate the air bag and thus ensure
its safety function.
To ensure the safety of your child, it
is essential to disarm the passenger
air bag when you install a rear-facing
child seat on the front passenger seat.
Otherwise, the child would risk being
seriously injured or killed if the air bag
w e r e t o i n fl a t e .
With the ignition switched off
,
insert the key into the passenger air
bag disarming switch, turn it to the
"OFF" position, then remove the key
keeping the slot in this position. The knee airbag protects the driver's
knees in the event of a serious front
impact.
I t i s fi t t e d i n t h e d a s h b o a r d b e l o w t h e
steering column.
In the event of a malfunction
* According to country. Triggering
It is deployed at the same time as the
front airbags.
Instrument panel warning lamp.
If this warning lamp comes on, ac-
companied by an audible signal and a
message on the multifunction screen,
contact a PEUGEOT dealer to have
the system checked. The airbags may
no longer be deployed in the event of
a serious impact. Knee airbag
When the ignition is on, this
warning light remains lit on the
instrument panel for the duration
of disarming.
In the "OFF" position, the passenger
air bag will not be triggered in the event
of an impact.
Page 109 of 249
7SAFETY
91
Disarming the front
passenger's front air bag * Reactivation
As soon as the child seat is removed,
turn the air bag slot to the
"ON" position
to re-activate the air bag and thus ensure
its safety function.
To ensure the safety of your child, it
is essential to disarm the passenger
air bag when you install a rear-facing
child seat on the front passenger seat.
Otherwise, the child would risk being
seriously injured or killed if the air bag
w e r e t o i n fl a t e .
With the ignition switched off
,
insert the key into the passenger air
bag disarming switch, turn it to the
"OFF" position, then remove the key
keeping the slot in this position. The knee airbag protects the driver's
knees in the event of a serious front
impact.
I t i s fi t t e d i n t h e d a s h b o a r d b e l o w t h e
steering column.
In the event of a malfunction
* According to country. Triggering
It is deployed at the same time as the
front airbags.
Instrument panel warning lamp.
If this warning lamp comes on, ac-
companied by an audible signal and a
message on the multifunction screen,
contact a PEUGEOT dealer to have
the system checked. The airbags may
no longer be deployed in the event of
a serious impact. Knee airbag
When the ignition is on, this
warning light remains lit on the
instrument panel for the duration
of disarming.
In the "OFF" position, the passenger
air bag will not be triggered in the event
of an impact.
Page 112 of 249
8DRIVING
Auto-adaptive programme
select position D in the gate: the
gearbox operates in auto-adaptive
mode, without any action on your
part, taking into account the follow-
ing parameters:
- the style of driving,
- t h e p r o fi l e o f t h e r o a d ,
- the vehicle load.
To obtain maximum acceleration with-
out touching the lever, press the ac-
celerator down fully (kick down). The
programme will change down auto-
matically or will stay in the gear select-
ed until the maximum engine speed is
reached.
When the brake is applied, the pro-
gramme will change down automati-
c a l l y i n o r d e r t o p r o v i d e e f fi c i e n t e n g i n e
braking. Sport and Snow programmes
These are two special programmes.
The programme selected is displayed
on the instrument panel screen.
It is only possible to change
from one gear to another if
the vehicle speed and engine
speed permit. If they do not,
the vehicle will operate temporarily in
automatic mode.
When the vehicle is stationary or mo-
ving very slowly, the gearbox automa-
tically selects gear M1 .
Programmes S (sport) and (snow)
do not operate in manual gear selec-
tion mode.
Any operating abnormal-
ity is indicated by lighting of
this warning lamp, accom-
panied by an audible signal
and a message on the multi-function
screen.
In this situation the gearbox oper-
ates in downgrade mode (locked in
3rd gear). You may feel a substantial
knock when changing from P to R and
from N to R (this will not cause any
damage to the gearbox).
Do not exceed 60 mph (100 km/h) and
keep within local speed limits.
Have it checked by a PEUGEOT dealer.
Operating check
Operation with manual
selection of the gears
select position M in the gate,
push the lever to the + sign to
change up a gear and push again
to change up another gear,
pull the lever to the - sign to change
down a gear and pull again to
change down another gear.
You can change from position D (driv-
ing in automatic mode) to position M
(driving in manual mode) at any time.
Releasing the accelerator
sharply does not have any im-
mediate effect on the speed of
the vehicle.
Never select position
N when
the vehicle is moving.
Never select positions P or R
unless the vehicle is stationary.
Never change between positions to
optimise braking on a slippery surface. Sport programme
Press button S once the vehicle
has been started in position D , the
auto-adaptive programme favours
dynamic driving.
Snow programme
This programme improves starting and
drive when traction is poor.
Press button once the vehicle
has been started and position D has
been selected, the auto-adaptive
programme adjusts the performance
of the vehicle to the condition of the
slippery road.
You can deactivate the Sport or Snow
programme at any time by pressing
the button selected.
I f t h e b a t t e r y i s fl a t a n d t h e l e -
ver is in position P , it will be
impossible to change to an-
other position.
In particular, do not force the lever
or there is a risk the gearbox may be
damaged.
Page 132 of 249
1010PRACTICAL INFORMATION
116
CHANGING A FRONT BULB
Handle the bulbs with a dry cloth.
2 - Main beam headlamps: H7-55W.
Remove the protective cover cor-
responding to the faulty bulb.
Disconnect the connector.
Press the end of the securing clips
to free the bulb. Change the bulb.
W h e n fi t t i n g t h e n e w b u l b , e n s u r e
that the direction notches are po-
sitioned correctly and the securing
c l i p s a r e fi x e d p r o p e r l y .
Reconnect the connector.
R e fi t t h e p r o t e c t i v e c o v e r .
4 - Direction indicators:
PY21W (amber).
Turn the bulb holder a quarter turn
and remove it.
Change the bulb.
WARNING: RISK OF ELEC-
TROCUTION
Front lamps
In the engine compartment, remove
the cover secured by one or two but-
t e r fl y s c r e w s , a p l a s t i c r e t a i n e r c l i p a n d
two quarter turn screws.
1 - Dipped beam headlamps: H1-
55W or D2S-35W xenon bulb.
Xenon bulbs must be replaced by a
PEUGEOT dealer. Amber coloured bulbs (direc-
tion indicators and side re-
peaters) must be replaced
w i t h b u l b s o f i d e n t i c a l s p e c i fi -
cation and colour.
5 - Front foglamps: H11 - 55W.
Turn the wheels to full lock.
A c c e s s t o t h e b u l b i s v i a t h e fl a p i n t h e
f r o n t m u d fl a p .
Consult a PEUGEOT dealer.
T h e h e a d l a m p s a r e fi t t e d w i t h p o l y c a r -
bonate glass with a protective coating.
Do not clean them with a dry or abra-
sive cloth, nor with a detergent or sol-
vent product.
E n s u r e t h a t t h e l i q u i d u s e d t o fi l l t h e
wash-wipe and headlamp wash reser-
voir is of good quality.
High pressure washing :
when using a high pressure
washer on stubborn dirt, do
not persist on the headlamps,
the other lamps and their surrounds
to avoid damaging their coating and
seals.
In certain climatic conditions (low tem-
perature, humidity), condensation on
the inside surface of the headlamp
glass and rear lights glass is normal;
it disappears a few minutes after the
lighting is switched on.
3 - Sidelamps: W5W.
Remove the protective cover, dis-
connect the connector and then
remove the bulb and change it.
Put the connector back in place.
Reconnect the connector.
R e fi t t h e p r o t e c t i v e c o v e r .
Page 133 of 249
1010PRACTICAL INFORMATION
117
Integrated direction indicator side
repeaters CHANGING A REAR BULB (SALOON)
Third brake light:
Five W 5 W bulbs.
Remove the plastic cover carefully
by unclipping it at the centre and
on either side, perpendicular to its
direction of engagement.
Press on the two tabs located at
the rear, near the rear screen.
Pull the red transparent cover out-
wards while maintaining the pressure
on the tabs.
Change the faulty bulb.
W h e n r e fi t t i n g , e n s u r e t h a t t h e
tabs of the red transparent cover
are engaged correctly and that the
upper trim has been put back in
place correctly.
R e fi t t h e l a m p fi x i n g n u t s i n s i d e
the boot using the towing eye, if
n e c e s s a r y . W h e n r e fi t t i n g , e n s u r e
that the lamp unit is positioned and
fi x e d c o r r e c t l y .
Reconnect the electrical connector.
Number plate lamps : W5W.
Remove the transparent cover us-
ing a screwdriver blade.
Change the faulty bulb.
Push the repeater forwards or
backwards and release it.
Unclip the repeater and change it.
Repeaters can be obtained from
PEUGEOT dealers.
Amber coloured bulbs (direction indi-
cators and side repeaters), must be
replaced with bulbs of identical speci-
fi c a t i o n a n d c o l o u r .
1. Direction indicators :
PY21W (amber).
2. Reversing lamps : P21W.
3. Foglamps/sidelamps :
P21/4W.
4. Sidelamps : P21/4W.
5. Brake lamps/sidelamps : P21/4W.
Disconnect the electrical connector.
U n s c r e w t h e l a m p fi x i n g n u t s i n -
side the boot using the towing eye
(stored inside the spare wheel), if
necessary.
Remove the seal.
Unclip the bulb holder moving
aside the 5 tabs.
Unscrew the bulb and change it.
R e fi t t h e b u l b h o l d e r .
Reposition the seal.