2010 MITSUBISHI GRANDIS instrument cluster

Driving range
E00509400016
This
value shows the distance (in km or miles) that
can be driven on the fuel remaining in the fuel tank. NOTE
l If

the driving range drops below 50 km
(30 miles) while the driving range is dis-
played, the display shows “---”. When this oc-
curs, top up the fuel tank as soon as possible.
l The driving range varies depending on road
conditions, the manner of driving and other
related factors. Consequently, the display
should be used only as a guide. It is recom-
mended to add fuel as soon as the low fuel
warning lamp in the instrument cluster illumi-
nates.
(Refer to “Low fuel warning lamp” on page
3-04.)
l Refueling will update the driving range indi-
cation. l
The
driving range displayed is based on pre-
vious fuel consumption data. Disconnecting
the battery cable will result in the deletion of
existing fuel consumption data, which will af-
fect the unit’s calculations.
l The driving range figure can occasionally in-
crease if the vehicle is stopped on an incline.
This is because the fuel has moved in the
tank because of the incline and is not consid-
ered as a fault.
Average speed E00509500062
This value shows the average speed (in km/h or
mph) since the display was reset. Refer to

“To reset
the display” on page 3-13. l
Automatic reset mode
When

4 hours have passed after the ignition
switch is turned to the “OFF” or “ACC” posi-
tion, the display is automatically reset. It
then shows “---”. l
Manual reset mode
If

you reset the display at the time when you
want to start the measurements, average
speed from that point of time can be displayed.
To reset the display, push the “DISP” button
for about 5 seconds or more. NOTE
l While

the ignition switch is in the “ON” po-
sition, the automatic reset mode is permanent-
ly selected. If you wish to make continuous
measurements, select the manual mode. Instruments and controls
3-15 3
Presented by http://mmc-manuals.ru/ \251

l
When the key has been turned to either the
“LOCK” or “ACC” position or removed
from the ignition switch with the lamp
switch in the “ ”
position, and the lamp
switch is turned to the “OFF” position within
approximately 3 minutes, the auto-cutout
function will not be activated.
(Even if the lamp switch is again turned to
the “ ”
position, the lamps will not go off
automatically; the lamps will remain on as
normal.)
When you want to keep the lamps on l Turn the switch in the “OFF” position to
switch off all lamps while the key is in the
“LOCK” or “ACC” position or remove the
key from the ignition switch.
l Turn on the lamps with the switch in the
“ ”
or “ ” position again, then the
lamps will remain on.
NOTE l It is possible to disable the lamps auto-cutout
function. For further information, we recom-
mend you to consult a MITSUBISHI
MOTORS Authorized Service Point.
Lamp monitor buzzer E00506100012
If the driver’s door is opened when the key is in the
“LOCK”

or “ACC” position or removed from the
ignition switch while the lamps are on, a buzzer
will sound to remind the driver to turn off the
lamps. When the lamp auto-cutout function acts,
the buzzer will stop automatically. When this func-
tion does not act, turn off the lamp switch to stop
the buzzer. Dipper (High/Low beam change)
E00506200114
When

the lamp switch is in the “ ”
position, the
beam changes from high to low (or low to high)
each time the lever is pulled to (1). While the high-
beam is on, the high-beam indication lamp in the in-
strument cluster will also illuminate. Headlamp flasher
E00506300333
The high-beams flash when the lever is pulled slight-
ly (2), and will go off when it is released.
When

the high-beam is on, the high-beam indica-
tion lamp in the instrument cluster will illuminate.
NOTE
l The high-beams can also flash when the
lamp switch is OFF.
l If you turn the lamps off with the headlamps
set to high-beam illumination, the headlamps
are automatically returned to their low-beam
setting when the lamp switch is next turned
to the “ ” position.Headlamp levelling
E00506400767
Headlamp levelling switch*
Except for vehicles with discharge headlamps
The

angle of the headlamp beam varies depending
on the load carried by the vehicle.
The headlamp levelling switch can be used to ad-
just the headlamp illumination distance (when the
lower beam is illuminated) so that the headlamps’
glare does not distract other drivers.
Set the switch (referring to the following table) to
the appropriate position according to the number of
people and the load in the vehicle. <6-person seat>
Vehi-
cle
condi- tion Switch
posi-tion “0” “1” “2” “3” “4” Instruments and controls
3-19 3
Presented by http://mmc-manuals.ru/ \251

Turn/Lane-change signals
E00506501156
The
turn-signal lamps flash when the switch is op-
erated (with the ignition switch in the “ON” posi-
tion). At the same time, the turn signal indicator
flashes. 1- Turn-signals
When
making a normal turn, use position
(1). The lever will return automatically when
cornering is completed.
There are times when the lever will not re-
turn after cornering. This occurs when the
steering wheel is turned only slightly.
In such cases, return the lever by hand.
2- Lane-change signals When changing lanes, use position (2). It
will return to the neutral position when re-
leased.
NOTE l If the lamp flashes unusually quickly, the
bulb in a turn-signal lamp may have burned
out. We recommend you to have the vehicle
inspected. l
It
is possible to activate the following func-
tions. For further information, we recom-
mend you to consult a MITSUBISHI
MOTORS Authorized Service Point.
On a vehicle equipped with a Multi Display
Station (MDS), the functions can be adjusted
on the screen. Refer to the separate operation
manual for details. • Sounding of a buzzer as the turn-signallamps flash.
• Flashing of the turn-signal lamps and the indication lamp in the meter when the lev-
er is operated with the ignition switch in
the “ACC” position. Hazard warning flasher switch
E00506600567
Use
the hazard warning flasher switch when the ve-
hicle has to be parked on the road for any emergency.
The hazard warning flashers can always be operat-
ed, regardless of the position of the ignition key.

Push the switch to turn on the hazard warning flash-
ers; push the switch again to turn them off.
When this switch is operated, all turn-signal lamps
flash continuously, as do the turn-signal indication
lamps in the instrument cluster. NOTE
l If

the lamps are kept flashing for a long time,
the battery will be discharged, resulting in
hard engine starting or no start condition. Instruments and controls
3-21 3
Presented by http://mmc-manuals.ru/ \251

l
It is possible to cause a buzzer to sound in
time with flashing of the turn-signal lamps.
For further information, we recommend you
to consult a MITSUBISHI MOTORS Author-
ized Service Point.
On a vehicle equipped with a Multi Display
Station (MDS), the functions can be adjusted
on the screen. Refer to the separate operation
manual for details. Fog lamp switch
E00506700018
Front fog lamp switch E00508300050
The front fog lamp can be operated when the head-
lamps

or tail lamps turn on. Push the switch to turn
on the front fog lamps, and push the switch again
to turn them off.
The indication lamp in the instrument cluster will
illuminate while the front fog lamps are on. NOTE
l The

front fog lamps are automatically turned
off when the headlamps and tail lamps turn
off. To turn on the front fog lamps again,
push the switch again when the headlamps or
tail lamps turn on.
l In case of vehicles with Daytime Running
Lamp, the front fog lamps can be operated
even if the lamp switch is set to the “OFF”
position, because the low beam of the head-
lamps, tail lamps, etc. illuminate when the ig-
nition key is at the “ON” position. Rear fog lamp switch
E00508400237
The

rear fog lamp can be operated when the head-
lamps or front fog lamps are on. Push the switch to
turn on the rear fog lamp, and push the switch
again to turn it off.
The indication lamp in the instrument cluster will
illuminate while the rear fog lamp is on. NOTE
l The

rear fog lamp is automatically turned off
when the headlamps and front fog lamps are
turned off. To turn on the rear fog lamp
again, push the switch again when the head-
lamps or front fog lamps are on.
l In case of vehicles with Daytime Running
Lamp, the rear fog lamp can be operated
even if the lamp switch is set to the “OFF”
position, because the low beam of the head-
lamps, tail lamps, etc. illuminate when the ig-
nition key is at the “ON” position. Instruments and controls
3-22
3
Presented by http://mmc-manuals.ru/ \251