2010 MITSUBISHI GRANDIS stop start

Blower speed selection switch
E00706300104
When
the blower speed selection switch or AUTO
switch is pressed, the air conditioning (cooling and
dehumidifying functions) starts operating. When
the OFF switch (A) is pressed, it stops.
The indication lamp (B) for the selected blower
speed illuminates. NOTE
l The blower speed is memorized when the en-
gine is shut down.
If

the battery is disconnected and reconnec-
ted, however, the memory is erased and the
blower speed is automatically set to the
“OFF” position.
Temperature control lever E00706400059
The temperature control lever is used to adjust the
air temperature. Move it rightward to increase the temperature and
leftward to reduce the temperature.
1- Low
2-

High
NOTE l The mode changes in accordance with the air
temperature. (Refer to “Changing the rear
mode selection” on page 5-04.)
l When the engine coolant temperature is ex-
tremely low (for example, in extremely cold
weather), moving the temperature control lev-
er has no effect on the air temperature. Operating the system in automatic
mode
E00706800141 1. Press the AUTO switch (A).
2.

Set the desired temperature using the temper-ature control lever (B). The temperature can
be set within a range from the minimum to
the maximum.
NOTE l Adjust the temperature to the desired level us-
ing the temperature control lever (centred for
reference).
l When the engine coolant temperature is ex-
tremely low (for example, in extremely cold
weather), moving the temperature control lev-
er has no effect on the air temperature. For pleasant driving
5-10
5
Presented by http://mmc-manuals.ru/ \251

NOTE
l The
repeat mode will be cancelled by press-
ing the TRACK button (5), the SCAN button
(6) or CD eject button (1).
l With a disc that contains both CD-DA and
MP3 files, the repeat mode causes only files
of the same format (CD-DA only or MP3
files only) to be repeated.
To change the order of tracks for playback
Random playback for a disc (music CDs only)
Press the RPT/RDM button (14) briefly. “RDM”
will appear on the display. Tracks on the currently
selected disc will be played in a random sequence.
To exit the random mode, press the RPT/RDM but-
ton again.
Random playback for all folders on a disc (MP3
CDs only)
Press the RPT/RDM button (14) briefly. “RDM”
will appear on the display. Tracks in the currently
selected disc will be played in a random sequence.
To exit the random mode, press the RPT/RDM but-
ton again. NOTE
l The
random mode will be cancelled by press-
ing the SCAN button (6) or the CD eject but-
ton (1).
l With a disc that contains both CD-DA and
MP3 files, the random mode causes only
files of the same format (CDDA only or
MP3 files only) to be played in a random se-
quence.
To find the start of each track on a disc for playback
Press the SCAN button (6). “SCAN” will appear
on the display and the CD player will play back the
first 10 seconds of each track on the selected disc.
The track number will blink while the scan mode is
selected. To exit the scan mode, press the SCAN
button again.
NOTE l Once all tracks on the disc have been scan-
ned, playback of the disc will restart from the
beginning of the track that was playing when
scanning started.
l The scan mode will be cancelled by selecting
the RPT/RDM button (14), the TRACK but-
ton (5) or the CD eject button (1).
l With a disc that contains both CD-DA and
MP3 files, the scan mode causes only files of
the same format (CD-DA only or MP3 files
only) to be played.
To eject a disc
When the CD eject button (1) is pressed, the disc
automatically stops and is ejected. The system auto-
matically switches to radio mode. CD text and MP3 title display
E00725000298
This
CD player can display CD text and MP3 titles
including ID3 tag information.
CD text
The CD player can display disc and track titles for
discs encoded with disc and track title information.
Press the TEXT button (9) repeatedly to make se-
lections in the following sequence: disc name track name normal display mode.
Disc
name
Track name
Normal display mode NOTE
l The

display can show up to 10 characters. If
a disc name or track name has more than 10
characters, press the PAGE button (11) to
view the next 10 characters.
l When there is no title information to be dis-
played, the display shows “NO TITLE”. For pleasant driving
5-26
5
Presented by http://mmc-manuals.ru/ \251

l
Characters that the CD player cannot display
are shown as an asterisk.
MP3 title
The CD player can display folder and track titles
for discs encoded with folder and track informa-
tion. Press the TEXT button (9) for less than 1 sec-
ond repeatedly to make selections in the following
sequence: folder name track name normal
display mode. ID3 tag information
The

CD player can display ID3 tag information for
files that have been recorded with ID3 tag informa-
tion. 1. Press the TEXT button (9) for 2 seconds orlonger to switch to the ID3 tag information.
“TAG” indicator will appear on the display. 2. Then
press the DISP button for less than 1
second repeatedly to make selections in the
following sequence: album name track
name artist name normal display mode.
NOTE l To

return from ID3 tag information to the
folder name, press the TEXT button (9)
again for 2 seconds or longer.
l When there is no title information to be dis-
played, the display shows “NO TITLE”.
l The display can show up to 10 characters. If
a folder name, track name, or item of ID3 tag
information has more than 10 characters,
press the PAGE button (11) to view the next
10 characters.
l Folder names and track names can each be
displayed up to a length of 10 characters.
Items of ID3 tag information can each be dis-
played up to a length of 10 characters.
l Characters that the CD player cannot display
are shown as an asterisk.
With a CD autochanger 1. Press the CD button (11), and the CD autoch-anger mode will be selected, starting playback.
2. To adjust the volume and tone, refer to “To adjust the volume” on page 5-15 and “To ad-
just the tone” on page 5-15.
3. To stop the CD player, turn off the power by pressing the PWR switch (13) or switch to
the radio mode by pressing the AM/FM but-
ton (7).
4. For information concerning the handling of compact discs, refer to “Handling of compact
discs” on page 5-30.
To select a desired disc (CD autochanger only)
You can select by using the DISC button (10 or 12). Disc up
Press

the DISC button (12) until the desired disc is
reached. The disc indicator (16) will display the se-
lected disc number.
Disc down
Press the DISC button (10) until the desired disc is
reached. The disc indicator (16) will display the se-
lected disc number. For pleasant driving
5-27 5
Presented by http://mmc-manuals.ru/ \251

l
Do not put additional labels (A) or stickers
(B) on compact discs. Also, do not use any
compact disc on which a label or sticker has
started to peel off or any compact disc that
has stickiness or other contamination left by
a peeled-off label or sticker. If you use such
a compact disc, the CD player may stop work-
ing properly and you may not be able to eject
the compact disc. Notes on CD-Rs/RWs
E00725100026
l You
may have trouble playing back some
CD-R/RW discs recorded on CD recorders
(CD-R/RW drives), either due to their record-
ing characteristics or dirt, fingerprints,
scratches, etc. on the disc surface.
l CD-R/RW discs are less resistant to high tem-
peratures and high humidity than ordinary mu-
sic CDs. Leaving them inside a vehicle for ex-
tended periods may damage them and make
playback impossible. l
The
unit may not successfully play back a
CD-R/RW that was made by the combina-
tion of writing software, a CD recorder
(CD-R/RW drive) and a disc if they are in-
compatible with one another.
l This player cannot play the CD-R/RW discs
if the session is not closed.
l This player cannot play CD-R/RW discs
which contain other than CD-DA or MP3 da-
ta (Video CD, etc.).
l Be sure to observe the handling instructions
for the CD-R/RW disc. WARNING
l Operating
the CD player in a manner oth-
er than specifically instructed herein may
result in hazardous radiation exposure.
Do not remove the cover and attempt to
repair the CD player by yourself. There
are no user serviceable parts inside. In
case of malfunction, we recommend you
to have it checked. Antenna
E00710500064
Glass antenna
The

antenna wire is printed in the left rear quarter
window glass. A- Antenna wire
NOTE l When

cleaning the rear quarter window
glass, use a soft cloth along the antenna wire
to keep it from getting damaged. For pleasant driving
5-31 5
Presented by http://mmc-manuals.ru/ \251

If the vehicle breaks down
E00800100778
If
the vehicle breaks down on the road, move it to
the shoulder and use the hazard warning flashers and/
or the warning triangle etc.
Refer to “Hazard warning flasher switch” on page
3-21.
If the engine stops/fails
Vehicle operation and control are affected if the en-
gine stops.
Before moving the vehicle to a safe area, be aware
of the following:
l The brake booster becomes inoperative and
the pedal effort will increase. Press down the
brake pedal harder than usual.
l Since the power steering pump is no longer
operative, the steering wheel feels heavy
when turning it. Turn the wheel with more ef-
fort than usual. Emergency starting
E00800502301
If
the engine cannot be started because the battery
is weak or dead, the battery from another vehicle
can be used with jumper cables to start the engine. WARNING
l To
start the engine by use of jumper ca-
bles from another vehicle, perform the cor-
rect procedures according to the instruc-
tion manual. Incorrect procedures could
result in a fire or explosion or damage to
the vehicles.
1. Get
the vehicles close enough so the jumper cables can reach, but be sure the vehicles
aren’t touching each other. If they are, it
could cause a ground connection you don’t
want. The vehicle will not start, and the bad
grounding could damage the electrical sys-
tems. CAUTION
l
Check
the other vehicle. It must have a 12-
volt battery.
If the other system isn’t 12-volt, shorting
can damage both vehicles.
2. You
could be injured if the vehicles move. Set the parking brake firmly on each vehicle.
Put an A/T in “P” (PARK) or a M/T in “N”
(Neutral). Turn off the ignition switch. WARNING
l Turn
off the ignition on both vehicles be-
forehand. Take care to make sure that
the cables or your clothes are never
caught by the fan or drive belt. Personal
injury could result.
NOTE l Turn

off all lamps, heater and other electrical
loads. This will avoid sparks and help save
both batteries.
3. Make sure battery electrolyte is at the proper level. Refer to “Battery” on page 8-10. WARNING
l If
electrolyte fluid is not visible, or ap-
pears to be frozen, Do Not Attempt Jump
Starting!
A battery might rupture or explode if the
temperature is below the freezing point
or if it is not filled to the proper level.
4. Connect the booster battery. Petrol-powered vehicles
Connect

one end of one jumper cable to the
positive (+) terminal of the discharged bat- For emergencies
6-02
6
Presented by http://mmc-manuals.ru/ \251

nutes, then start the engine in the vehicle
with the discharged battery.
CAUTION
l
Keep the engine of the vehicle giving assis-
tance running.
7. After
the engine is started, disconnect the ca- bles in the reverse order. WARNING
l Charging
the battery while it is installed
in the vehicle might cause the battery to
catch fire and explode. Or damage to the
vehicle could result. If it has to be charg-
ed in that condition for unavoidable rea-
sons, disconnect the vehicle side negative
(-) terminal connected to the battery.
l Keep sparks, cigarettes and flames away
from the battery because the battery may
produce an explosion.
l Use adequate ventilation when charging
or using the battery in an enclosed space.
l Remove all the caps before charging the
battery.
l Electrolyte is corrosive diluted sulphuric
acid.
If electrolyte (battery acid) comes into con-
tact with your hands, eyes, clothes and
the painted surface of your vehicle, it
should be thoroughly flushed with water.
If electrolyte gets in your eyes, flush them
with water immediately and thoroughly,
and get prompt medical attention. CAUTION
l
Do
not attempt to start the engine by pull-
ing or pushing the vehicle.
It could damage your vehicle.
l Always wear protective eye goggles when
working near the battery.
l Keep the battery out of the reach of chil-
dren.
NOTE l If

the vehicle is put in motion without fully
charging the battery, it might cause the loss
of smooth engine operation and the anti-lock
brake warning lamp to illuminate. Refer to
“Anti-lock brake system (ABS)” on page
4-21. Engine overheating
E00800602126
If

the water temperature gauge indication remains
in the overheating zone for a long time, the engine
may be overheating. If this occurs, take the follow-
ing corrective measures: 1. Stop the vehicle in a safe place.
2. Check whether steam is coming from the en-gine compartment.

[If steam does not come from the engine com-
partment]
With the engine still running, raise the bon-
net to ventilate the engine compartment.

[If steam is coming from the engine compart-
ment]
Stop the engine, and when the steam stops,
raise the bonnet to ventilate the engine com-
partment. Restart the engine. WARNING
l Do
not open the bonnet while steam is com-
ing from the engine compartment. It
could cause steam or hot water to spurt
out, causing burns. Hot water could spurt
out even when there is no steam coming
out, and some parts will be very hot. Be
very careful when opening the bonnet.
l Be careful of hot steam, which could be
blowing off the reserve tank cap.
l Do not attempt to remove the radiator
cap (petrol-powered vehicles) or reserve
tank cap (diesel-powered vehicles) while
the engine is hot. For emergencies
6-04
6
Presented by http://mmc-manuals.ru/ \251

WARNING
l Set the jack only at the positions shown
here. If the jack is set at a wrong position,
it could dent your vehicle or the jack
might fall over and cause personal injury.
l Do not use the jack on a tilted or soft sur-
face.
Otherwise, the jack might slip and cause
personal injury. Always use the jack on a
flat, hard surface. Before setting the jack,
make sure there are no sand or pebbles
under the jack base.
7. Rotate
the jack by hand until the flange por- tion (D) fits in the groove (E) at the top of
the jack. 8. Remove
the wheel nut wrench and bar from
under the third seat. (Refer to “Tools and
jack” on page 6-06.)
9. Insert the bar (F) into the wheel nut wrench (G). Then put the end of the bar into the
shaft’s jack end, as shown in the illustration. Slowly rotate the wheel nut wrench until the
tyre is raised slightly off the ground surface.
WARNING
l Stop
jacking up the vehicle as soon as the
tyre is raised off the ground. It is danger-
ous to raise the vehicle any higher.
l Do not get under your vehicle while using
the jack.
l Do not bump the raised vehicle or leave it
sitting on the jack for a long time. Both
are very dangerous.
l Do not use a jack except the one that
came with your vehicle.
l The jack should not be used for any pur-
pose other than to change a tyre.
l No one should be in your vehicle when us-
ing the jack.
l Do not start or run the engine while your
vehicle is on the jack.
l Do not turn the raised wheel. The tyres
still on the ground could turn and make
your vehicle fall off the jack. Spare wheel
E00801101440
Check

the air pressure of the spare tyre frequently
and make sure it is ready for emergency use at any
time.

Maintaining the spare wheel at the highest speci-
fied air pressure will ensure that it can always be
used under any conditions (city/high-speed driving,
varying load weight, etc.).
The spare wheel is stored under the rear of the body.
Compact spare wheel
The compact spare tyre is designed to save space in
the luggage compartment and its lighter weight
makes it easier to use if a flat tyre occurs. CAUTION
l
The
pressure should be periodically
checked and maintained at the specified
pressure while the tyre is stowed.
Driving with an insufficient tyre pressure
can lead to an accident. If you have no
choice but to drive with an insufficient
tyre pressure, keep your speed down and
inflate the tyre to the correct pressure as
soon as possible. (Refer to “Tyre inflation
pressures” on page 8-12.)
l The compact spare wheel is for tempora-
ry use only and should be removed as
soon as the original wheel can be re-
paired or replaced.
l The vehicle must not be driven at speeds
in excess of 80 km/h (50 mph) while using
the compact spare wheel. For emergencies
6-08
6
Presented by http://mmc-manuals.ru/ \251

The catalytic converter itself gets hot quickly, and
may
be damaged if overheated. The following
points should be noted in order to prevent the igni-
tion of unburned petrol within the catalytic convert-
er.
l Use UNLEADED PETROL ONLY of the
type recommended in “Fuel selection” on
page 02.
l Do not drive with an extremely low fuel lev-
el; running out of fuel could cause damage to
the catalytic converter.
l Do not attempt to start the engine by pushing
the vehicle. If the battery is weak or dis-
charged, use another battery to start the en-
gine.
l Do not idle the engine with any spark plug
wires disconnected or removed such as per-
forming diagnostic tests.
l Do not idle the engine for prolonged periods
during very rough idle or malfunctioning op-
erating conditions.
l Do not race the engine when turning off the
ignition switch. This will cause the catalytic
converter to be damaged due to contact with
unburnt fuel.
l Stop driving the vehicle if you think the per-
formance is noticeably low, or if the engine
has a malfunction such as with the ignition,
etc.
If it is impractical to stop driving immediate-
ly, reduce the speed and drive for only a
short time. We recommend you to have your
vehicle inspected as soon as possible. l
In unusual situations involving grossly mal-
functioning engine operation, a burnt smell
may indicate severe and abnormal catalyst
overheating.
If this occurs, the vehicle should be stopped
in a safe place, the engine switched off and
the vehicle allowed to cool. Once the engine
is cool, a service, including a tune-up to man-
ufacturer’s specifications, should be obtained
immediately. Bonnet
E01000302076
To open
Pull
the release lever towards you to unlock the bon-
net. Raise the bonnet while pressing the safety lock. Maintenance
8-03 8
Presented by http://mmc-manuals.ru/ \251