2010 MITSUBISHI GRANDIS motor

Display brightness adjustment
E00509600018
1. Press
and hold down button (A), then press
the “H” button (B) within 1 second. A buz-
zer will sound, and the system will allow ad-
justment of the display brightness. 2. Adjust
the brightness by pressing the “H” but-
ton (B) or “M” button (C). H- Decrease brightness
M- Increase brightness 3. Press
the “SET” button (D) to determine the
setting. The display will return to the original
display item. NOTE
l To

cancel the brightness adjusting procedure
before completion, press the button (A).
l If the “SET” button (D) is not pressed for
about 15 seconds or longer in the middle of
the adjustment, the currently selected bright-
ness is set automatically. The display will re-
turn to the original display item.
Display unit selection E00509700051
It is possible to change the units in which distance,
fuel consumption, and time are displayed.
NOTE
l Except

for vehicles with MITSUBISHI
MOTORS genuine audio, only the unit of mo-
mentary fuel consumption can be changed to
km or miles. 1. Press
and hold down button (A), then press
the “M” button (B) within 1 second. A buz-
zer will sound, and the system will allow
units to be changed. 2. Use
the “H” button (C) or “M” button (B) to
select the desired speed unit, then press the
“SET” button (D) to enter the setting. Instruments and controls
3-16
3
Presented by http://mmc-manuals.ru/ \251

l
When the key has been turned to either the
“LOCK” or “ACC” position or removed
from the ignition switch with the lamp
switch in the “ ”
position, and the lamp
switch is turned to the “OFF” position within
approximately 3 minutes, the auto-cutout
function will not be activated.
(Even if the lamp switch is again turned to
the “ ”
position, the lamps will not go off
automatically; the lamps will remain on as
normal.)
When you want to keep the lamps on l Turn the switch in the “OFF” position to
switch off all lamps while the key is in the
“LOCK” or “ACC” position or remove the
key from the ignition switch.
l Turn on the lamps with the switch in the
“ ”
or “ ” position again, then the
lamps will remain on.
NOTE l It is possible to disable the lamps auto-cutout
function. For further information, we recom-
mend you to consult a MITSUBISHI
MOTORS Authorized Service Point.
Lamp monitor buzzer E00506100012
If the driver’s door is opened when the key is in the
“LOCK”

or “ACC” position or removed from the
ignition switch while the lamps are on, a buzzer
will sound to remind the driver to turn off the
lamps. When the lamp auto-cutout function acts,
the buzzer will stop automatically. When this func-
tion does not act, turn off the lamp switch to stop
the buzzer. Dipper (High/Low beam change)
E00506200114
When

the lamp switch is in the “ ”
position, the
beam changes from high to low (or low to high)
each time the lever is pulled to (1). While the high-
beam is on, the high-beam indication lamp in the in-
strument cluster will also illuminate. Headlamp flasher
E00506300333
The high-beams flash when the lever is pulled slight-
ly (2), and will go off when it is released.
When

the high-beam is on, the high-beam indica-
tion lamp in the instrument cluster will illuminate.
NOTE
l The high-beams can also flash when the
lamp switch is OFF.
l If you turn the lamps off with the headlamps
set to high-beam illumination, the headlamps
are automatically returned to their low-beam
setting when the lamp switch is next turned
to the “ ” position.Headlamp levelling
E00506400767
Headlamp levelling switch*
Except for vehicles with discharge headlamps
The

angle of the headlamp beam varies depending
on the load carried by the vehicle.
The headlamp levelling switch can be used to ad-
just the headlamp illumination distance (when the
lower beam is illuminated) so that the headlamps’
glare does not distract other drivers.
Set the switch (referring to the following table) to
the appropriate position according to the number of
people and the load in the vehicle. <6-person seat>
Vehi-
cle
condi- tion Switch
posi-tion “0” “1” “2” “3” “4” Instruments and controls
3-19 3
Presented by http://mmc-manuals.ru/ \251

Turn/Lane-change signals
E00506501156
The
turn-signal lamps flash when the switch is op-
erated (with the ignition switch in the “ON” posi-
tion). At the same time, the turn signal indicator
flashes. 1- Turn-signals
When
making a normal turn, use position
(1). The lever will return automatically when
cornering is completed.
There are times when the lever will not re-
turn after cornering. This occurs when the
steering wheel is turned only slightly.
In such cases, return the lever by hand.
2- Lane-change signals When changing lanes, use position (2). It
will return to the neutral position when re-
leased.
NOTE l If the lamp flashes unusually quickly, the
bulb in a turn-signal lamp may have burned
out. We recommend you to have the vehicle
inspected. l
It
is possible to activate the following func-
tions. For further information, we recom-
mend you to consult a MITSUBISHI
MOTORS Authorized Service Point.
On a vehicle equipped with a Multi Display
Station (MDS), the functions can be adjusted
on the screen. Refer to the separate operation
manual for details. • Sounding of a buzzer as the turn-signallamps flash.
• Flashing of the turn-signal lamps and the indication lamp in the meter when the lev-
er is operated with the ignition switch in
the “ACC” position. Hazard warning flasher switch
E00506600567
Use
the hazard warning flasher switch when the ve-
hicle has to be parked on the road for any emergency.
The hazard warning flashers can always be operat-
ed, regardless of the position of the ignition key.

Push the switch to turn on the hazard warning flash-
ers; push the switch again to turn them off.
When this switch is operated, all turn-signal lamps
flash continuously, as do the turn-signal indication
lamps in the instrument cluster. NOTE
l If

the lamps are kept flashing for a long time,
the battery will be discharged, resulting in
hard engine starting or no start condition. Instruments and controls
3-21 3
Presented by http://mmc-manuals.ru/ \251

l
It is possible to cause a buzzer to sound in
time with flashing of the turn-signal lamps.
For further information, we recommend you
to consult a MITSUBISHI MOTORS Author-
ized Service Point.
On a vehicle equipped with a Multi Display
Station (MDS), the functions can be adjusted
on the screen. Refer to the separate operation
manual for details. Fog lamp switch
E00506700018
Front fog lamp switch E00508300050
The front fog lamp can be operated when the head-
lamps

or tail lamps turn on. Push the switch to turn
on the front fog lamps, and push the switch again
to turn them off.
The indication lamp in the instrument cluster will
illuminate while the front fog lamps are on. NOTE
l The

front fog lamps are automatically turned
off when the headlamps and tail lamps turn
off. To turn on the front fog lamps again,
push the switch again when the headlamps or
tail lamps turn on.
l In case of vehicles with Daytime Running
Lamp, the front fog lamps can be operated
even if the lamp switch is set to the “OFF”
position, because the low beam of the head-
lamps, tail lamps, etc. illuminate when the ig-
nition key is at the “ON” position. Rear fog lamp switch
E00508400237
The

rear fog lamp can be operated when the head-
lamps or front fog lamps are on. Push the switch to
turn on the rear fog lamp, and push the switch
again to turn it off.
The indication lamp in the instrument cluster will
illuminate while the rear fog lamp is on. NOTE
l The

rear fog lamp is automatically turned off
when the headlamps and front fog lamps are
turned off. To turn on the rear fog lamp
again, push the switch again when the head-
lamps or front fog lamps are on.
l In case of vehicles with Daytime Running
Lamp, the rear fog lamp can be operated
even if the lamp switch is set to the “OFF”
position, because the low beam of the head-
lamps, tail lamps, etc. illuminate when the ig-
nition key is at the “ON” position. Instruments and controls
3-22
3
Presented by http://mmc-manuals.ru/ \251

Wiper and washer switch
E00507101162
The
windscreen wiper and washer can be operated
with the ignition switch in the “ON” or “ACC” po-
sition.
Move the switch to operate the windscreen wipers
or spray the washer fluid.
Windscreen wipers MIST- Misting function
The wipers will operate once.
OFF- Off
INT- Speed sensitive intermittent operation The intermittent intervals will change
with the speed of the vehicle.
LO- Slow
HI- Fast NOTE
l The speed-sensitive-operation function of the
windscreen wipers can be deactivated.
For
further information, we recommend you
to consult a MITSUBISHI MOTORS Author-
ized Service Point.
On a vehicle equipped with a Multi Display
Station (MDS), the functions can be adjusted
on the screen. Refer to the separate operation
manual for details.
To adjust intermittent intervals
With the lever in the “INT” (speed-sensitive inter-
mittent operation) position, the intermittent inter-
vals can be adjusted by turning the knob (A). 1- Fast
2-

Slow
Misting function
Move the lever in the direction of the arrow and re-
lease, to operate the wipers once.
Use this function when you are driving in mist or
drizzle. If the lever is held in the upward position (MIST),
the

wipers continue operating until the lever is re-
leased. Windscreen washer
E00507200531
The washer fluid will be sprayed onto the wind-
screen

by pulling the lever towards you. The wip-
ers operate automatically several times while the
washer fluid is being sprayed.
On a vehicle equipped with a headlamp washer, the
headlamp washer operates together with the wind-
screen washer the first time the windscreen washer
is used if the headlamps are on. Instruments and controls
3-23 3
Presented by http://mmc-manuals.ru/ \251

CAUTION
l
If the washer is used in cold weather, the
washer fluid sprayed against the glass
may freeze resulting in poor visibility.
Heat the glass with the defroster or demis-
ter before using the washer.
NOTE l It

is possible to spray washer fluid without ac-
tivating the wipers. To do so, hold the lever
in the pulled position and turn the ignition
switch to the “ON” or “ACC” position.
l It is possible to cause the wipers never to op-
erate when washer fluid is sprayed. For fur-
ther information, we recommend you to con-
sult a MITSUBISHI MOTORS Authorized
Service Point.
On a vehicle equipped with a Multi Display
Station (MDS), the functions can be adjusted
on the screen. Refer to the separate operation
manual for details.
Rear window wiper and washer E00507300460
The rear window wiper and washer switch can be
operated

with the ignition switch in the “ON” or
“ACC” position. Turn the knob, and the rear window wiper will op-
erate.
INT- The wiper operates continuously for sev-
eral
seconds then operates intermittently
at intervals of about every 8 seconds
OFF- Off -
The washer fluid will be sprayed onto
the

rear window when the knob is turned
fully in either direction.
The wipers operate automatically several
times while the washer fluid is being
sprayed. NOTE
l To

ensure a clear rearward view, the wiper
performs a number of continuous operations
either when the switch is moved to the
“INT” position or when the gearshift lever
(M/T) or the selector lever (A/T) is moved to
the “R” position while the switch is in the
“INT” position.
Following this continuous operation, the wip-
er will automatically switch to intermittent op-
eration.
l It is possible to spray washer fluid without ac-
tivating the wiper. To do so, hold the knob at
the end of the lever in the “ ”
position and
turn the ignition switch to the “ON” or
“ACC” position.
l It is possible to activate the following func-
tions. For further information, we recom-
mend you to consult a MITSUBISHI
MOTORS Authorized Service Point.
On a vehicle equipped with a Multi Display
Station (MDS), the functions can be adjusted
on the screen. Refer to the separate operation
manual for details.
• Adjustment of the interval for intermit-tent operation
• Causing the wipers to switch to continu- ous operation when the knob at the end
of the lever is turned to the “INT” posi-
tion twice within approximately 1 second
• Changing intermittent wiper operation to continuous wiper operation
• Causing the wiper never to operate when washer fluid is sprayed. Instruments and controls
3-24
3
Presented by http://mmc-manuals.ru/ \251

Precautions to observe when using wip-
ers and washers
E00507600014
l If
the moving wipers become blocked by ice
or other deposits on the glass, the motor may
burn out even if the wiper switch is turned to
OFF. If obstruction occurs, park your vehicle
in a safe place, turn off the ignition, and
clean the deposits from the glass so that the
wipers operate smoothly.
l Do not use the wipers when the glass is dry.
They may scratch the glass surface or the
blades may prematurely wear out.
l Before using the wipers in cold weather,
check that the wiper blades are not frozen on-
to the glass. The motor may burn out if the
wipers are used with the blades frozen onto
the glass.
l Avoid using the washer continuously for
more than 20 seconds. Do not operate the
washer when the fluid reservoir is empty.
Otherwise, the motor may burn out.
l Periodically check the level of washer fluid
in the reservoir and refill if required.
During cold weather, add a recommended
washer solution that will not freeze in the
washer reservoir. Failure to do so could re-
sult in loss of washer function and frost dam-
age to the system components. Headlamp washer switch*
E00507800218
The
headlamp washer can be operated when the ig-
nition switch is in the “ON” or “ACC” position and
the headlamps are on.

Push the button once and the washer fluid will be
sprayed on to the headlamps. NOTE
l If

the ignition switch is in the “ON” or
“ACC” position and the headlamps are on,
the headlamp washer operates together with
the windscreen washer the first time the wind-
screen washer lever is pulled. Rear window demister switch
E00507901144
The

rear window demister switch can be operated
with the ignition switch in the “ON” position.
Push the switch to turn on the rear window demis-
ter. It will be turned off automatically in about 20
minutes. To turn off the demister within about 20
minutes, push the switch again.
The indication lamp (A) will illuminate while the
demister is on. NOTE
l When

the rear window demister switch is
pressed, the outside rear-view mirrors are de-
fogged or defrosted. Refer to “Heated mir-
ror” on page 4-08.
l The demister switch is not to melt snow but
to clear mist. Remove snow before use of the
demister switch.
l To avoid unnecessary discharge of the bat-
tery, do not use the rear window demister dur-
ing starting of the engine or when the engine
is not running. Turn the demister off immedi-
ately after the window is clear. Instruments and controls
3-25 3
Presented by http://mmc-manuals.ru/ \251

The mirrors can be extended and retracted for 30
seconds
after the ignition switch is turned to the
“LOCK” position.
Either the mirror switch in the cabin or the remote
controller of the keyless entry system (if so equip-
ped) can be used.
For information on the keyless entry system, refer
to page 1-04.
NOTE
l It is also possible to fold and return the mir-
rors by hand.
l When freezing has occurred and mirrors fail
to operate as intended, please refrain from re-
peated pushing of the retractor switch as this
action can result in burn-out of the mirror mo-
tor circuits.
Automatic extension of mirrors
If the engine is stopped and started with the mirrors
retracted, the mirrors automatically extend for safe-
ty when the vehicle speed reaches 30 km/h
(19 mph).
NOTE l If the mirrors are retracted manually or using
the mirror switch after the engine is started,
they do not extend automatically. Use the mir-
ror switch to extend the mirrors, or turn the
ignition switch to the “LOCK” position to ac-
tivate the automatic extension function. Heated mirror*
E00601200442
When
the rear window demister switch is pressed,
the outside rear-view mirrors are demisted or de-
frosted. Current will flow through the heater ele-
ment inside the mirrors, thus clearing away frost or
condensation.
The indication lamp (C) will illuminate while the
demister is on. The heater will be turned off auto-
matically in about 20 minutes. Ignition switch
E00601401731 LOCK
The

engine is stopped and the steering wheel
locked. The key can be inserted and removed only
when the switch is in this position.
ACC
The engine is stopped, but the electrical devices
such as the radio and cigarette lighter can be operat-
ed.
ON
The engine is running, and all the vehicle’s electri-
cal devices can be operated.
START
The starter motor operates. After the engine has star-
ted, release the key and it will automatically return
to the “ON” position. Starting and driving
4-08
4 M/T
A/T
Presented by http://mmc-manuals.ru/ \251