2010 MERCEDES-BENZ E-CLASS CABRIOLET service

the
mtoa Mercedes-Benz Service Centre or
to as pecial collectio npoint for old batteries. G
Risk of inju
ry
Fo rs afety reasons, Mercedes-Benz recom-
mends that you only use batteries which have
been tested and approved for your vehicle by
Mercedes-Benz. Thes ebatteries provide
increased impact protection to prevent vehi-
cle occupant sfrom suffering aci dburns
should the battery be damaged in the event
of an accident.
To prevent acid burns, observe the following
safety notes when handling batteries:
R do not lean over the battery.
R do not place any metal objects on abattery.
Otherwise ,you coul dcause ashort circuit
and the battery's gas mixtur ecould ignite.
R mak esure that you do not create an elec-
trostatic charge, e.g. by wearing synthetic
clothing or as aresult of friction on fabrics.
Therefore, you should not pull or slide the
batter yover carpets or other synthetic
materials.
R neve rtouch the battery first. To discharge
ap ossible electrostatic charge, step out of
the vehicle first and touc hthe bodywork.
R do not wipe the battery usin gacloth. The
battery may explode as aresult of electro-
static charge or due to flying sparks.
! Switc hoff th eengine and remove the key
before disconnectin gthe termi nalclamps
from the battery .Onvehicles with KEY-
LE SS -GO, make sure that the ignition is
switched off. Check that all the indicator
lamps in the instrument cluste rare off.
Otherwise, yo umay destroy electronic
components, such as the alternator.
i Remove the key if you park the vehicle
and do not require any electrical consum-
ers. The vehicle will then use very little
energy, thus conserving battery power.
Mercedes-Benz recommends that you do not
carr yout work on batteries yourself, e.g.
removing, charging or replacing. Always have this work performed at
aqualified specialist
workshop, e.g. aMercedes-Ben zService
Cent re. Installation location of the battery
Your vehicle is equippe dwithabatter yint he
engin ecompartmen t. Itis located on the front
bulkhea dunder the filter box on the right-
hand sid eofthe vehicle when viewed in the
direction of travel.
X Appl ythe parkin gbrake firml yand on vehi-
cles with automati ctransmission, shift the
transmission to position P.
X Switch off all electrica lconsumers, e.g.
radio, blower ,etc.
X Turn the key to position 0(Ypage 135) in
the ignition lock and remove it, or, with
KEYLESS-GO, make sure that the ignition
has bee nswitched off (Y page 135). All
indicator lamps must be off in the instru-
ment cluster.
X Open the bonnet (Y page 259). X
Release clamps ;on filter box :.
X Remove filter box :.
i Information on disconnecting the battery
(Y page 286). Disconnecting the battery
G
Risk of accident
If the battery is disconnected: 286
BatteryBreakdown assistance
BA 207 ECE ÄJ 2010/1a; 1; 2, en-GB
mkalafa
Version: 3.0.2.11 2010-01-26T13:03:22+01:00-Seite 286

Jum
p-starting G
Risk of injury
There is arisk of acid burns when jump-starting avehicle due to the gases which escape from
the battery. Do not lean over the batter ywhile the engin eisbeing jump-started. G
Risk of explosion
Gases escapin gfrom th ebattery during jump-starting may cause minor explosions. Avoid cre-
ating sparks. Keep naked flames away from the battery, and do not smoke.
Comply with safety precautions when handling batteries. You will find these under "Battery" in
the index.
! Avoid repeated and lengthy startin gattempts. Otherwise, non-combuste dfuel may dam-
age the catalytic converter 41
and create arisk of fire.
Do not use arapid-charging device to start the engine.
Make sure the jump leads are not damaged.
Make sure the jump leads are not touching any other metal objects when they are connected
to the battery.
If your vehicle's battery is discharged ,the engin ecan be jump-started from another vehicle
or from asecond batter yusing jum pleads.
Observ ethe followin gpoints:
X The battery is not accessible in all vehicles. If the other vehicle' sbattery is not accessible,
jump-start the vehicle using asecond batter yorajump-star ting device.
X Only jump-start the vehicl ewhen th eengineisc old an dthe catalytic converter system has
cooled down 42
.
X Do no tstart the engine if the battery is frozen. Let the battery thaw first.
X Jump-starting may only be performed from batterie swithanominal voltage of 12 V.
X Only use jum pleads which have asufficient cross-section and insulated terminal clamps.
X Make sure that the jump leads cannot come into contact with parts, such as the pulley or
the fan. Thes eparts move when the engine is started and while it is running.
X If the battery is fully discharged ,leave the batter ythat is being used to jump-star tconnected
for afew minutes befor eattempting to start. This charges the battery alittle.
i Jump leads and further information about jump-startin gcan be obtained from any
Mercedes-Ben zService Centre.
X Make sure that the two vehicles do not touch.
X Apply the parking brak efirmly.
X Manual transmission: engage neutral.
X Automatic transmission: move the selector lever toP.
X Switch off all electrical consumer s(e.g. radio, blower, etc.).
X Open the bonnet (Y page 259).
41 Only vehicles with apetrol engine.
42 Only vehicles with apetrol engine. Jump-starting
289Breakdown assistance
BA 207ECE ÄJ 2010 /1a;1;2,e n-GB
mkalafa Version: 3.0.2.11 2010-01-26T13:03:22+01:00-Seite 289 Z

Position number
Bidentifie sthe charged batter yofthe other vehicle or an equivalen tjump-
starting device.
X Slide cover :of positive terminal ;in the direction of the arrow.
X Connec tpositiv eterminal ;on your vehicle to positiv eterminal =of donor battery B
using the jum plead, beginning with your own battery.
X Start the engine of the donor vehicle and run it at idling speed.
X Connect negative terminal ?of donor battery Bto eart hpoint Aof your vehicle using
the jum plead, connectin gthe jum plead to donor battery Bfirst.
X Start the engine.
X First remove the jum plead from eart hpoint Aand negative terminal ?,then from positive
terminal ;and positive terminal =,each time disconnecting from the battery on your own
vehicle first.
X Have the battery checked at aqualified specialist workshop, e.g. aMercedes-Ben zService
Cent re. Towin
gand tow-star ting Important safet
ynotes
When towing, observe the legal requirements
in all countries concerned. G
Risk of accident
If you tow the vehicle, you must use arigid
towing bar if: R
the engin eisnot run ning.
R there is abrake system malfunction.
R there is amalfunction in the voltage supply
or the vehicle's electrical system.
The power steering and the brake forc eboos-
ter do not work when the engin eisnot run-
nin g. Yo uwill then need considerably more
forc etos teer and to brake and the brake
peda ltrave lwill be longer. If necessary,
depress the brake pedal with maximum force. 290
Towing and tow-startingBreakdown assistance
BA 207 ECE ÄJ 2010/1a; 1; 2, en-GB
mkalafa
Version: 3.0.2.11
2010-01-26T13:03:22+01:00
-Seite 290

!
Only lash the vehicle down by the wheels
or wheel rims, not by parts of the vehicle
suc hasa xle or steering components. Oth-
erwise, the vehicl ecould be damaged. Tow-star
ting (emergency engine
starting)
Please note:
R vehicles with an automatic transmission
must not be tow-started.
R the batter ymust be connected.
R the engine and catalytic converter must be
cold.
R avoid repeated and lengthy starting
attempts.
Vehicles with manual transmission:
X Turn the key to position 2in the ignition
lock.
X Fully depres sthe clutc hpedal.
X Shif tton eutral.
X Tow the vehicle or let it roll.
X Shif ttoas uitable gear and bring the clutch
pedal up slowly. Do not depres sthe accel-
erator pedal.
The engin eisstarted. Fuses
Important safet
ynotes
The fuses in your vehicle serve to close down
faulty circuits. If afuse blows, all the compo-
nen tson th ecircuit and their function swill
fail. G
Ris
koff ire
Only use fuses that have been approve dfor
Mercedes-Ben zvehicles and which have the
cor rect fuse rating for the systems con-
cerned. Do not attempt to repai rorbridge
faulty fuses .Otherwise, acircuit overload
could cause afire. Have the cause traced and
rectified at aqualified specialist workshop,
e.g. aMercedes-Benz Ser vice Centre. Blow
nfuses must be replaced with fuses of
the same rating, which you can recognise by
the colour and value. The fuse ratings are lis-
ted in the fuse allocation chart .AMercedes-
Ben zService Cent rewill be happy to advise
you.
If the newly inserted fuse also blows, have the
cause traced and rectified at aqualified spe-
cialist workshop, e.g. aMercedes-Benz
Ser vice Centre.
! Onlyuse fuses that hav ebeen approved
for Mercedes-Ben zvehicles and which
have the cor rect fuse rating for the system
concerned. Otherwise, compo nentso rsys-
tems could be damaged. Befor
echangin gafuse
X Park th evehicle and apply the parking
brake.
X Swit choff all elect rical consumers.
X Remove the key from the ignitio nlock.
The fuses ar elocated in variou sfuse boxes:
R fuse box on the driver' sside of the dash-
board
R fuse box in the engin ecompartmen tonthe
driver's side
R fuse box in the boot on the right when
viewed in the direction of travel
The fuse allocation char tisl ocated in the
vehicle tool kit (Y page 274)in the stowage
compar tment under the boot floor. Fuse box under the dashboard
! Do not use apointed objec tsuch as a
screwdriver to open the cover in the dash-
board. You could damage the dashboard or
the cover. Fuses
293Breakdown assistance
BA 207ECE ÄJ 2010/1a; 1; 2, en-GB
mkalafa Version:3.0.2.11
2010-01-26T13:03:22+01:00
-Seite 293 Z

Vehicl
eequipment
i Thismanua ldesc ribe sallthe standard
and optional equipment of your vehicle
which wa savailable at th etime of pur-
chase. Countr y-specif ic differences are
possible. Bear in mind tha tyour vehicle
ma ynot featur eall function sdescribed
here. Important safet
ynotes G
Risk of accident
Tyres, wheels or accessories which have not
been approved by Mercedes-Benz for your
vehicle or are not used as they should be, can
impair drivin gsafety. As aresult, you could
cause an accident. Befor epurchasing and
using them, enquire about their suitability,
legal stipulatio nsand factory recommenda-
tions at aMercedes-Benz Ser vice Centre.
! For safety reasons ,Mercedes-Ben zrec-
ommends that you only use tyres, wheels
and accessories which have been approved
by Mercedes-Ben zspecifically for your
vehicle. These tyres have been specially
adapted for use with the contro lsystems,
such as AB SorESP®
,a nd are marked as
follows:
R MO =Mercedes-Ben zOriginal
R MOE =Mercedes-Ben zOriginal Extended
(tyres with run-flat characteristics)
R MO1 =Mercedes-Ben zOriginal (AMG)
Only use Mercedes-Benz Original Extended
tyres on wheels that have been specifically
approved by Mercedes-Benz.
If you use other tyres, wheels and acces-
sories, Mercedes-Benz cannot accept any
responsibility for damage that may result
from this. Further informat ionabout tyres,
wheels and approved combinations can be
obtained from any Mercedes-Benz Service
Centre. !
Retreaded tyres are neither tested nor
recommended by Mercedes-Benz, since
previous damage cannot alway sbedetec-
ted on retreaded tyres. As aresult,
Mercedes-Ben zcannot guarantee vehicle
safety if retreade dtyres are fitted. Do not
fit use dtyres if you have no information
about their previous usage.
Mod ification work on the brake system and
wheels is not permitted, nor is the use of
space rplates or brake dust shields .This inva-
lidates the Genera lOperating Permit for the
vehicle.
i Further information about tyres and
wheels can be obtained from any
Mercedes- Benz Servic eCentre. Directives to be observed
R Only fit tyres and wheels of the same type
and make.
R Only fit tyres of the correc tsize ont othe
wheels.
R Afterf itting new tyres, run them in at mod-
erate speeds for the first 100 km as they
only reach their full performanc eafter this
distance.
R Do not drive wit htyres which have too little
tread depth ,asthis significantly reduces
the traction on wet roads (aquaplaning).
R While driving, pay attention to vibrations,
noises and unusual handling characteris-
tics, e.g. pulling to one side. This ma yindi-
cate that the wheels or tyres are damaged.
If you suspect that atyre is defective,
reduce your speed immediately. Stop the
vehicle as soo naspossible to chec kthe
wheels and tyres for damage. Hidden tyre
damage could also be causing the unusual
handling characteristics. If you fin dno
signs of damage, hav ethe wheels and tyres
examined at aspecialist workshop, for 298
Directives to be observedTyres and wheels
BA 20
7ECE ÄJ 2010 /1a; 1; 2, en-GB
mkalafa Version: 3.0.2.11 2010-01-26T13:03:22+01:00 -Seite 298

tyre
siss etcorrectl yfor the respective
operating con ditions.
X Observe the note sinthe sectio nontyre
pressures (Y page 299). G
Ris
kofa ccident
The tyr epressure loss warning system can
only give reliable warnings if you have se tthe
co rrec ttyrep ressure.
If an incorrect tyre pressure is se t,these
incorrect values will be monitored.
At yre with insufficient pressure results in
vehicle instability when driving, thu sincreas-
ing the risk of an accident.
X Make sure that the key is in pos i-
tion 2(Ypage135) in the igniti onlock.
In the multifunction display you wil lsee the
standard display (Y page 197).
X Press the =or; button to select the
Service menu.
X Press the 9or: button to select
Tyre pressure.
X Press the abutton.
The multifunction display show sthe mes-
sage:
Ru nF lat Indicator active Restart
with OK
If you wish to confirm the restart:
X Press the abutton.
Th em ultifunction displa yshows the mes-
sage:
Tyre press. no wOK?
X Press 9or: to select Yes.
X Press the abutton.
Th em ultifunction displa yshows the mes-
sage:
Ru nF lat Indicator restarted
After ateach-in period, the tyr epressure
loss warning system wil lmonitor the set
tyr ep ressures of all fou rtyres. If you wish to cancel the restart:
X
Press the %button.
or
X If the Tyrepress. now OK? message
appe ars,use9 or: to select Can‐
cel.
X Press the abutton.
The tyre pressure values stored at the last
restart will continue to be monitored. Direction of rotation
Tyres with aspecified direction of rotation
have additional benefits, e.g. if there is arisk
of aquaplaning. You will only gain these ben-
efits if the correct direction of rotation is
observed.
An arrow on the sidewall of the tyre indicates
its correct direction of rotation.
You may fit an emergenc yspare wheel/spare
wheel against the direction of rotation.
Observe the tim erestric tion on use as well as
the speed limitation specified on the emer-
genc yspare wheel/spar ewheel. Interchanging th
ewheels G
Ris
kofa ccident
Interchange the front and rear wheels only if
they have the same dimensions: for example
size, offset, etc.
After every wheel interchange/change, have
the tightening torque checked at aqualified
specialist workshop that has the necessary
specialist knowledg eand tool stocarry out
the work required. Mercedes-Benz recom-
mends that you use aMercedes-Ben zService
Centr efor this purpose. In particular ,work
relevant to safet yoronsafety-related sys-
tems must be carried out at aqualified spe-
cialist workshop.
The wheel scould work loose if they are not
tightened to atorqu eof130 Nm. 302
Interchanging th
ewheelsTyres and wheels
BA 207 ECE ÄJ 2010/1a; 1; 2, en-GB
mkalafa Version: 3.0.2.11 2010-01-26T13:03:22+01:00-Seite 302

For safety reasons, Mercedes-Benz recom-
mends that yo
uonly use wheel bolts of the
correct size which hav ebeena pproved for
Mercedes-Benz vehicles.
The wear patterns on the fron tand rea rtyres
differ ,dependin gonthe opera tingconditions.
Interchange the wheels befor eaclear wear
pattern ha sform edon the tyr es.F ront tyres
typicall ywearm ore on the shoulder sand the
rea rtyre sint he centre.
On vehicles that have the same size front and
rear wheels, you can interchange the wheels
every 500 0kmto10,000 km depending on
the degre eoftyre wear. Do not reverse the
direction of tyre rotation.
Clea nthe con tact surface softhe wheel and
the brake disc thoroughly ever ytime awheel
is interchanged. Chec kthe tyr epressure and,
if necessary, restart th etyre pressure loss
warning system. Wheel and tyr
ecombinations Please bear the followin
ginmind
! For safety reasons, Mercedes-Ben zrec-
ommends that you only use tyres, wheels
and accessories which have been approved
by Mercedes-Ben zspecifically for your
vehicle. These tyres have been specially
adapted for use with the contro lsystems,
such as AB SorESP®
,a nd are marked as
follows:
R MO =Mercedes-Ben zOriginal
R MOE =Mercedes-Ben zOriginal Extended
(tyres with run-flat characteristics)
R MO1 =Mercedes-Ben zOriginal (AMG)
Only use Mercedes-Benz Original Extended
tyres on wheels that have been specifically
approved by Mercedes-Benz.
If you use other tyres, wheels and acces-
sories, Mercedes-Benz cannot accept any
responsibility for damage that may result
from this. Further informat ionabout tyres,
wheels and approved combinations can be obtained from any Mercedes-Benz Service
Centre.
! If you fit tyres other than those tested and
recommended by Mercedes-Benz, charac-
teristics such as handling, noise levels and
fuel consumption, etc. may be adversely
affected. In addition, when driving with a
load, tyre dimensional variations could
caus ethe tyres to com einto contact with
the bod ywork and axle components. This
could result in dam agetot he tyres or the
vehicle.
i Further information about tyres and
wheels can be obtained from any
Mercedes-Benz Servic eCentre.
i You will fin datable of tyre pressures on
the insid eofyourv ehicle' sfuel filler flap.
For further information on tyre pressure,
see (Y page 299).
i Notes on the vehicle equipment:
Always fit the vehicle:
R with tyres of the same size on agiven axle
(left/right)
R with the same type of tyres at agiven
time (summer tyres, winter tyres,
MOExtended tyres)
i Vehicles featurin gthe MOExtended run-
fla ts ystem are not equipped with the
TIREFIT kit.
It is therefore recommended that you addi-
tionally equip your vehicle with the TIREFIT
kit if you fit tyres that do not feature run-
flat properties, e.g. winter tyres.
AT IREFIT kit is availa blef rom any qu alified
specialist workshop, e.g. aMercedes-Benz
Ser vice Centre. Wheel and tyr
ecombinations
303Tyres and wheels
BA 207ECE ÄJ 2010/1a; 1; 2, en-GB
mkalafa Version:3.0.2.11
2010-01-26T13:03:22+01:0
0-Seite 303 Z

E2
00 CGI 43
E2 20 CDI 43
E2 50 CGI 43
E2 50 CDI 43
E3 50
E3 50 CGI 43
E3 50 CDI 43 E5
00 R17 BA
Summer tyres
46 235/45 R17 94 W
or
235/45 R17 94 W
MOExtended
47 —
Winter tyres
235/45 R17 94 H
M+S
i
or
235/45 R17 94 H
M+S i
MOExtended 47
,48 235/45 R17 94 H
M+Si
or
235/45 R17 94 H
M+Si
MO
Exte nded 47, 48 Light-
alloy wheels 7.5J
x17H2ET45 7.5J
x17H2ET45 E2
00 CGI 43
E2 20 CDI 43
E2 50 CGI 43
E2 50 CDI 43
E3 50
E3 50 CGI 43
E3 50 CDI 43 E5
00 R18 BA Winter tyres
235/40 R18 95
HXL
M+S i 235/40 R1
895HXL
M+S i Ligh
t-alloy wheels 8.0J
x18H2ET45 8.0J
x18H2ET45 Mixed tyres
i FA:front axle, RA: rear axle
43 BlueEFFICI ENCY.
46 Cabriolet :not in combination with Sports package code 950/952, sports suspension code 48 6ordynamic
handling package code 483.
47 Tyres with run-flat characteristics and only in combination with an activated tyre pressure loss warning
syste mort yre pressure monitor.
48 Winter tyres for retrofitting. Only certain tyre brands are approved. Ask your Mercedes-Benz Service Centre
for more information. Wheel and tyr
ecombinations
305Tyres and wheels
BA 207ECE ÄJ 2010 /1a; 1; 2, en-GB
mkalafa Version: 3.0.2.11 2010-01-26T13:03:22+01:00 -Seite 305 Z