2010 MERCEDES-BENZ E-CLASS CABRIOLET bonnet

X
Pull release lever :on the bonnet.
The bonnet is released.
! Make sure that the windscreen wiper sare
not folde daway from the windscreen .Oth-
erwise, yo ucould damage the windscreen
wipers or the bonnet. X
Reach int othe gap, pull bonnet catch han-
dle ;up and lift the bonnet.
Closin gthe bonnet G
Ris
kofi njury
Make sure tha tnobody can becom etrapped
as you close th ebonnet.
X Lower the bonnet and let it fal lfrom a
height of approximatel y20c m.
X Check that th ebonnet has engaged prop-
erly.
If the bonnet can be raised slightly ,itisn ot
properly engaged. Open it again and close
it with alittle more force. Engine oil
Notes on the oil level Depending on drivin
gstyle, the vehicle con-
sumes amaximum of 0.8 loil per 100 0km.
Th eo il consumption may be higher than this
when the vehicle is new or if you frequently
drive at high engine speeds.
When checking the oil level:
R park the vehicle on alevel surface.
R the engine should be switched off for at
least fiv eminutes if the engine is at normal
operating temperature.
R the engine should be switched off for at
least thirt yminutes if the engine is not at
normal operating temperature, e.g. if the
engine was only started briefly.
Checking the oil level using the oil dip-
stick Depending on the engine, the oil dipstick may
be installed at
adifferent location. E3
50 (example)
X Pull oi ldipstick :out of the oil dipstick
tube.
X Wipe off oil dipstick :.
X Slowly insert oil dipstick :into the oil dip-
stick tube to the stop, and take it out again.
The oil level is correc tifthe level is between
MIN mark =and MAX mark ;.
X Top up the oil if necessary. 260
Engine compartmentMaintenance and care
BA 20
7ECE ÄJ 2010 /1a;1;2,e n-GB
mkalafa Version: 3.0.2.11 2010-01-26T13:03:22+01:00-Seite 260

After an accident
Problem Possible causes/consequences and
M Solutions
Fue
lisl eaking from the
vehicle. G
Ris
kofe xplosion or fire
The fuel line or the fuel tan kisf aulty.
X Immediately turn the key to position 0(Ypage 135)in the ignition
lock and remove it.
X Do not restart the engine under any circumstances.
X Consult aqualified special istworkshop. You are unable to
determine the exten
tof
the damag e. X
Consult aqualified specialis tworkshop. You can
notd etect any
damage. X
Start the engine as normal. The active bonnet func-
tion (pedestrian protec-
tion) has been trig-
gered. Your vehicle has been involved in
afrontal collision.
X Rese tthe triggered activ ebonnet (pedestrian protection)
(Y page 258). The NECK
-PRO head
restraints on the driv-
er's and front-
passenger seats have
been triggered. Your vehicle has been involved in
arear-end collision.
X Reset the triggered NECK-PRO head restraint s(Ypage 40). Where will
Ifind...? Wa
rning triangle
Removing the warning triangle X
Open the boot lid. Coupé (example)
X
Open the warning triangle holder and
remove warning triangle :. Where will
Ifind...?
273Breakdown assistance
BA 207ECE ÄJ 2010 /1a; 1; 2, en-GB
mkalafa Version: 3.0.2.11 2010-01-26T13:03:22+01:00 -Seite 273 Z

the
mtoa Mercedes-Benz Service Centre or
to as pecial collectio npoint for old batteries. G
Risk of inju
ry
Fo rs afety reasons, Mercedes-Benz recom-
mends that you only use batteries which have
been tested and approved for your vehicle by
Mercedes-Benz. Thes ebatteries provide
increased impact protection to prevent vehi-
cle occupant sfrom suffering aci dburns
should the battery be damaged in the event
of an accident.
To prevent acid burns, observe the following
safety notes when handling batteries:
R do not lean over the battery.
R do not place any metal objects on abattery.
Otherwise ,you coul dcause ashort circuit
and the battery's gas mixtur ecould ignite.
R mak esure that you do not create an elec-
trostatic charge, e.g. by wearing synthetic
clothing or as aresult of friction on fabrics.
Therefore, you should not pull or slide the
batter yover carpets or other synthetic
materials.
R neve rtouch the battery first. To discharge
ap ossible electrostatic charge, step out of
the vehicle first and touc hthe bodywork.
R do not wipe the battery usin gacloth. The
battery may explode as aresult of electro-
static charge or due to flying sparks.
! Switc hoff th eengine and remove the key
before disconnectin gthe termi nalclamps
from the battery .Onvehicles with KEY-
LE SS -GO, make sure that the ignition is
switched off. Check that all the indicator
lamps in the instrument cluste rare off.
Otherwise, yo umay destroy electronic
components, such as the alternator.
i Remove the key if you park the vehicle
and do not require any electrical consum-
ers. The vehicle will then use very little
energy, thus conserving battery power.
Mercedes-Benz recommends that you do not
carr yout work on batteries yourself, e.g.
removing, charging or replacing. Always have this work performed at
aqualified specialist
workshop, e.g. aMercedes-Ben zService
Cent re. Installation location of the battery
Your vehicle is equippe dwithabatter yint he
engin ecompartmen t. Itis located on the front
bulkhea dunder the filter box on the right-
hand sid eofthe vehicle when viewed in the
direction of travel.
X Appl ythe parkin gbrake firml yand on vehi-
cles with automati ctransmission, shift the
transmission to position P.
X Switch off all electrica lconsumers, e.g.
radio, blower ,etc.
X Turn the key to position 0(Ypage 135) in
the ignition lock and remove it, or, with
KEYLESS-GO, make sure that the ignition
has bee nswitched off (Y page 135). All
indicator lamps must be off in the instru-
ment cluster.
X Open the bonnet (Y page 259). X
Release clamps ;on filter box :.
X Remove filter box :.
i Information on disconnecting the battery
(Y page 286). Disconnecting the battery
G
Risk of accident
If the battery is disconnected: 286
BatteryBreakdown assistance
BA 207 ECE ÄJ 2010/1a; 1; 2, en-GB
mkalafa
Version: 3.0.2.11 2010-01-26T13:03:22+01:00-Seite 286

R
the brake boosting effect will not be avail-
able .Greater braking force wil lthen be
required and brake pedal travel will be lon-
ger. If necessar y,depress the brak epedal
with maximum force.
R the transmission is locked in position Pon
vehicles with automati ctransmission.
! Alwaysd isconnect the battery in the
order described below. Never mix up the
terminal clam pdisconnection/connection
order and never mix up the terminal
clam ps.You may otherwis edamag ethe
vehicle electronics. :
Battery
; Positive terminal
= Negativ eterminal
? Breather hose
X Remove the negative terminal clam pfrom
th eb attery.
X Remove the cover from the positive termi-
nal clamp.
X Remove the positive terminal clamp from
the battery.
X Disconnect the breather hose. Fittin
gand removin gthe battery
X To remove: disconnect th ebattery
(Y pag e286).
X Loose nthe bolt which holds the battery in
place. X
Rem ovet he battery.
X To fit: follow the steps described in "To
remove" in reverse order. Charging th
ebattery G
Ris
kofi njury
Only charge the batter yinawell-ventilated
area. As the battery is being charged ,gases
can escape and generate minor explosions.
This could injure you and other persons or
cause damage to the paintwork or acid cor-
rosion on the vehicle.
You can obtain information about battery
chargers which allow the battery to be
charged while still installed from aqualified
specialist workshop ,e.g. aM ercedes-Benz
Ser vice Centre. G
Risk of injury
There is arisk of acid burns during the charg-
ing process due to the gases which escape
from the battery. Do not lean over the battery
during the chargin gprocess. G
Ris
kofi njury
Bat tery aci discaustic. Avoid contact with the
skin, eyes or clothing.
! Only charge the installed batter ywith a
batter ycharger whic hhas been tested and
approved by Mercedes -Benz .These battery
chargers allow the battery to be charged
while still installed.
! Only use battery chargers with amaxi-
mum charging voltage of 14.8 V.
! Only charge the battery using the jump-
start connection point.
The jump-starting connection point is in the
engine compartmen t(Ypage 289).
X Open the bonnet (Y page 259).
X Connec tthe battery charger to the positive
terminal and earth point in the sam eorder Battery
287Breakdown assistance
BA 207 ECE ÄJ 2010/1a; 1; 2, en-GB
mkalafa Version: 3.0.2.11 2010-01-26T13:03:22+01:00-Seite 287 Z

as when con
necting the do norb atter yin
the jump-starting procedure
(Y page 289). Reconnecting th
ebattery
! Always connect the battery in the order
described below. Never swap the terminal
clamps. Yo umay otherwise damage the
vehicle elect ronics.
X Switch off all ele ctrical consumers, e.g.
radio, blower, etc.
X Connect the positiv eterminal clamp and
secur ethe cov er.
X Connect th enegative termina lclamp.
X Put th efilter box back in place, then clip in
and close th eretaining clamps.
X Close th ebonnet.
i If th epower supply has been interrupted,
e.g .ift he battery has been reconnected,
you must carry out the followin gtasks:
R set the clock (Y page 205)
R reset the function for folding the exterior
mirrors in/out automatically by folding
the mirrors out once (Y page 102)288
BatteryBreakdown assistance
BA 207 ECE ÄJ 2010/1a; 1; 2, en-GB
mkalafa
Version:3.0.2.11
2010-01-26T13:03:22+01:00
-Seite 288

Jum
p-starting G
Risk of injury
There is arisk of acid burns when jump-starting avehicle due to the gases which escape from
the battery. Do not lean over the batter ywhile the engin eisbeing jump-started. G
Risk of explosion
Gases escapin gfrom th ebattery during jump-starting may cause minor explosions. Avoid cre-
ating sparks. Keep naked flames away from the battery, and do not smoke.
Comply with safety precautions when handling batteries. You will find these under "Battery" in
the index.
! Avoid repeated and lengthy startin gattempts. Otherwise, non-combuste dfuel may dam-
age the catalytic converter 41
and create arisk of fire.
Do not use arapid-charging device to start the engine.
Make sure the jump leads are not damaged.
Make sure the jump leads are not touching any other metal objects when they are connected
to the battery.
If your vehicle's battery is discharged ,the engin ecan be jump-started from another vehicle
or from asecond batter yusing jum pleads.
Observ ethe followin gpoints:
X The battery is not accessible in all vehicles. If the other vehicle' sbattery is not accessible,
jump-start the vehicle using asecond batter yorajump-star ting device.
X Only jump-start the vehicl ewhen th eengineisc old an dthe catalytic converter system has
cooled down 42
.
X Do no tstart the engine if the battery is frozen. Let the battery thaw first.
X Jump-starting may only be performed from batterie swithanominal voltage of 12 V.
X Only use jum pleads which have asufficient cross-section and insulated terminal clamps.
X Make sure that the jump leads cannot come into contact with parts, such as the pulley or
the fan. Thes eparts move when the engine is started and while it is running.
X If the battery is fully discharged ,leave the batter ythat is being used to jump-star tconnected
for afew minutes befor eattempting to start. This charges the battery alittle.
i Jump leads and further information about jump-startin gcan be obtained from any
Mercedes-Ben zService Centre.
X Make sure that the two vehicles do not touch.
X Apply the parking brak efirmly.
X Manual transmission: engage neutral.
X Automatic transmission: move the selector lever toP.
X Switch off all electrical consumer s(e.g. radio, blower, etc.).
X Open the bonnet (Y page 259).
41 Only vehicles with apetrol engine.
42 Only vehicles with apetrol engine. Jump-starting
289Breakdown assistance
BA 207ECE ÄJ 2010 /1a;1;2,e n-GB
mkalafa Version: 3.0.2.11 2010-01-26T13:03:22+01:00-Seite 289 Z

X
To open: pull outcover :slightly at the
bottom in the direction of arrow =.
X Pull cover :outwards in the direction of
arrow ;and remove it.
X To close: clip in cover :on the front of
the dashboard.
X Fold cover :inwards until it engages. Fuse box in th
eengine compartment
X Make sure that the windscreen wiper sare
turne doff. G
Ris
kofi njury
Make sure that the windscreen wipers are
turned off and the key is pulled out of the igni-
tion lock befor eyou open the cover of the fuse
box. Otherwise, the windscreen wiper sand
the wipe rrods abov ethe cover coul dbeset
in motion .This coul dlead to you or others
being injured by the wiper rods.
X Open the bonnet (Y page 259). X
Remov eany existing moisture from the
fuse box using adry cloth.
X Take lines ;from th eguides.
X Move aside lines ;.Route the lines behind
con nection =to do this.
X To open: open clamps :.
X Remove the fuse bo xcover forwards.
X To close: checkwhether the rubber seal is
lyin gcorrectly in the cover.
X Insert the cover at the rea rofthe fuse box
int ot he retainer.
X Fold down the cover and close clamps :.
X Secur elines ;in the guides.
! The cover must be fitted properly, other-
wise moisture or dirt could impair the func-
tion of the fuses.
X Close the bonnet (Y page 260). Fuse box in the boot
X Open the boot lid. Coupé
X
To open: turn rotarycatch :clockwise.
X Open cover ;downwards. 294
FusesBreakdown assistance
BA 207 ECE ÄJ 2010/1a; 1; 2, en-GB
mkalafa
Version:3.0.2.11
2010-01-26T13:03:22+01:00
-Seite 294