2010 MERCEDES-BENZ E-CLASS CABRIOLET start stop button

Key positions
Key g
To remove th ekey
1 Powe rsupply for some consumers, such
as the windscreen wipers.
2 Ignition (power supply for all consumers)
and drive position
3 To start the engine
i The key can be turned in the ignition lock
even if it is not the correc tkey for the vehi-
cle. The ignition is then not switched on.
The engin ecannot be started.
KEYLESS-GO Pressing the Start/Stop button several times
in succession corresponds to the different
key positions in the ignition lock. This is only
the case if you are not depressing the brake
pedal.
If you depress the brake pedal and press the
Start/Stop button ,the engin estart simmedi-
ately. X
Position 0:ifStart/Sto pbutton :has not
yet been pressed, this corresponds to the
key being removed from the ignition.
X Position 1:pressStart/Sto pbutton :.
You can now activat ethe windscreen wip-
ers, for example.
i If you then open the driver's door when in
this position ,the power supply is deactiva-
ted.
X Position 2(ignition): press Start/Stop but-
ton :twice.
i If you press Start/Stop button :once
when in this position and the driver's door
is open, the power supply is deactivated
again.
Removing th eStart/Stop button
You can remove the Start/Stop butto nfrom
th ei gnition lock and star tthe vehicle as nor-
ma lusing the key.
i You do not hav etoremov ethe Start/Stop
button from the ignition lock when you
leav ethe vehicle. X
Remove Start/Stop button :from ignition
lock ;.
i When you inser tthe Start/Stop button
int ot he ignition lock ,the system needs
2s econds recognition tim ebefor eyou can
use the Start/Stop button. Driving
135Driving and parking
BA 207ECE ÄJ 2010/1a; 1; 2, en-GB
mkalafa Version:3.0.2.11
2010-01-26T13:03:22+01:0
0-Seite 135 Z

Sta
rting the engine
Impor tant safety instructions G
Risk of poisoning
Never leav ethe engin erunning in enclosed
spaces .The exhaust gases con tain carbon
monoxide. Inhaling exhaust fumes consti-
tutes ahealth hazar dand could lead to loss
of consciousness or even death.
! Do not depress the accelerator pedal
whe nstartin gthe engine.
Manua ltran smission X
Depress the brake pedal and keep it
depressed.
X Fully depress the clutch pedal.
X Shif tton eutral N.
i You can only star tthe engin ewhen the
clutc hpedal is fully depressed.
Automa tict ran smission X
Shif tthe transmission to position P.
i You can also star tthe engin ewhen the
transmission is in position N.
Sta rting procedur ewith the key X
To star tapetrol engine: turn the key to
position 3in the ignition lock
(Y page 135 )and releas eita ss oon as the
engin eisrunning.
X To star tadiesel engine: turn the key to
position 2in the ignition lock
(Y page 13 5).
The % preglow indicator lam pinthe
instrumen tcluster lights up.
X When the %preglow indicator lamp
goes out, tur nthe key to position 3
(Y page 135) and release it as soon as the
engin eisrunning.
i You can start the engine without preglow
if the engine is warm. i
Vehicles with automatic transmis-
sion: you can also use the touch-star tfunc-
tion. To do this, turn the key to position
3(Y page 135 )and releas eitimmediately.
Th ee ngine then starts automatically.
Starting the engine usin gKEYLESS-GO G
Risk of injury
Your vehicle can be started using avalid KEY-
LESS-GO key. For this reason, children should
never be left unsupervised in the vehicle.
Always take the key with you when leaving the
vehicle, even if you are only leaving it for a
short time.
i The Start/Stop button can be used to
start the vehicle manually without inserting
the key in the ignition lock. This mode for
startin gthe engin eoperates independently
of the ECO start /stop automatic engine
start function.
X Depres sthe brake pedal and keep it
depressed.
X To sta rtap etrol engine: press the Start/
Stop button (Y page 135) once.
The engin estarts.
X To start adiesel engine: press the Start/
Stop button (Y page 135)once.
Preglow is activated and the engin estarts. Pulling away
Manual transmission X
Depress the brake peda land keep it
depressed.
X Fully depress the clutch pedal.
X Shift to either first gea rorreverse gear R.
X Release the parkin gbrake (Y page 153).
X Releas ethe brake pedal.
X Slowly release the clu tchpedal and gently
depress the acc elerator pedal.136
Dr
ivingDriving and parking
BA 20 7ECE ÄJ 2010/1a; 1; 2, en-GB
mkalafa Version:3.0.2.11
2010-01-26T13:03:22+01:0
0-Seite 136

Vehicles with manual transmission
X
Shift to eithe rfirst or reverse gear R.
X Turn the key to position 0in the ignition
lock and remove it.
The immobiliser is activated.
X Apply the parkin gbrake firmly.
Vehicles with automati ctransmission X
Shift the transmission to position P.
With the key
X Turn the key to position 0in the ignition
lock and remove it.
The immo biliserisa ctivated.
X Apply the parking brake firmly.
i Thek ey can only be removed if the trans-
mission is in position P.
Usin gKEYLESS -GO
X Press the Start/Sto pbutton (Y page 135).
The engine stop sand al lthe indicator
lamps in the instrument cluster go out.
X Apply the parkin gbrake firmly.
i Thee ngine can be turne doff whil ethe
vehicle is in mot ionb ypress inga nd holding
the Start/Sto pbutton for thre eseconds. EC
Os tart/sto pfunction
Gen eral notes i
TheE CO start/stop function is only avail-
abl efor the E200 CG IBlueEFFICIENCY
model with manu altransmission.
The ECO start/sto pfunction switches the
engine off automatically in certain situations.
The engine starts automatically whe nyou pull
away again.
The ECO star t/stopfunction thereby helps
you to reduce the fuel consumption and emis-
sions of your vehicle. The ECO start/stop function is activated each
time the engine is switched on. The system is
operational when ECO symbol
:is shown in
the multifunction display.
! Always switch the ignition off and take the
key with you when leaving the vehicle.
Automatic engin eswitch-off The ECO start/stop function switche
soff the
engine automatically if you:
R apply th ebrake and bring th evehicle to a
standstill
R operat ethe clutc hpedal R
engage neutral N(follow gearshif tinstruc-
tion ;to engage neutral N,ifnecessary)
R release the clutch pedal
The engine is only switched off if:
R the outside temperature is within the range
which is suitabl efor the system.
R the engin eisatnormal operatin gtemper-
ature.
R the set temperature for the vehicle interior
has been reached. 138
DrivingDriving and parking
BA 20
7ECE ÄJ 2010 /1a; 1; 2, en-GB
mkalafa Version: 3.0.2.11 2010-01-26T13:03:22+01:00 -Seite 138

R
the battery is suffici ently charged.
R the syste mdetects that the windsc reen is
not misted up when the air-conditioni ng
syste misswitched on.
R the bonnet is closed.
R the driver's door is closed and the seat belt
is fastened.
R the vehicle is not being steered.
Automatic engine start If the engine has been switched off by the
ECO start/stop function
,itrestart sautomat-
ically if you:
R depres sthe clutc hpedal
R depress the accelera torp edal
The engin eisstarted during the automatic
stop phas eif:
R thes ystem is deactivated using the ECO
button.
R the vehicle start storoll.
R the brake system requires this.
R the system detects moistur eonthe wind-
screen when the air-conditionin gsystem is
switched on.
R the battery' scharge status is too low.
R the driver's seat belt is removed or the driv-
er' sd oor is opened.
R you steer the vehicle.
! Only engage gear when the clutc hpedal
is depressed. Deactiva
ting/activa ting th eECO start/
stop function :
To activate/deactivat ethe ECO star t/
stop function
; Indicator lamp
If indica torlamp ;is off, the ECO start/stop
function has been deactivated manually or as
the result of amalfunction. The engine will
then not be switched off automatically when
the vehicle stops.
i Each time the engine is switched on, the
ECO start/stop function is activated. Driving
139Driving and parking
BA 207 ECE ÄJ 201 0/1a; 1; 2, en-GB
mkalafa Version: 3.0.2.11 2010-01-26T13:03:22+01:00-Seite 139 Z

Problems wit
hthe engine Problem Possible causes/consequences and
M Solutions
Th
ee ngine doe snot
start. The HOL
Dfunction or DISTRONIC PLUS is activated.
X Deactivat ethe HOL Dfunction (Y page 172)orDISTRONIC
PLUS (Y page 160).
X Try to start th eengine again. The engine doe
snot
start. The starter motor
can be heard. R
There is amalfunction in the engine electronics.
R There is amalfunction in the fuel supply.
R The on-board voltage is too low because the starter battery is
too weak or discharged.
X Before attempting to start the engine again, turn the key in the
ignition back to position 0or press the Start/Stop button
repeatedly until all indicator lamps in the instrumen tcluster go
out.
X Try to star tthe engin eagain (Y page 136). Avoid excessively
long and frequen tattempt stostart the engine as thes ewill drain
the battery.
If the engine does not start after several attempts:
X Consult aqualified specialist workshop. The engine does not
start
.The starter motor
can be heard. The
reserve fuel warning
lam pisl it and the fuel
gauge displa yshows 0. The fuel tan
kise mpty.
X Refue lthe vehicle. The engin
edoes not
start. You cannot hear
the starter motor. The on-boar
dvoltage is too low because the starter battery is too
weak or discharged.
X Jump-start the vehicle (Y page 289).
If the engin edoes not star tdespite attempt stojump-start it:
X Consult aqualified specialist workshop. The starter motor was exposed to
athermal load that was too high.
X Allo wthe starter motor to cool down for approximatel ytwo
minutes.
X Try to start the engine again.
If the engine still does not start:
X Consult aqualified specialist workshop. 140
DrivingDrivin
gand pa rking
BA 20 7ECE ÄJ 2010 /1a;1;2,e n-GB
mkalafa Version: 3.0.2.11 2010-01-26T13:03:22+01:00-Seite 140

Problems wit
hthe transmission Problem Possible causes/consequences and
M Solutions
Th
et rans mission has
problem sshifting gear. The transmission is losing oil.
X
Hav ethe transmission chec kedataq ualified specialist work-
sho pimmediately. Th
ea cceleratio nability
is deteriorating.
The transmission no
longer changes gear. The transmission is in emergency mode.
It is only possible to shift into
2ndgear and reverse gear.
X Stop the vehicle.
X Shift the transmission to position P.
X Turn the key to position 0in the ignition lock or press the Star t/
Stop butto nrepeatedly until all indicator lamps in the instru-
men tcluster go out.
X Wait at least 10 seconds before restarting the engine.
X Shift the transmission to position Dor R.
If D is selected, the transmission shifts into 2ndgear; if Ris
selected, the transmission shifts into reverse gear.
X Hav ethe transmission chec kedataq ualified specialist work-
sho pimmediately. Releasin
gthe parking lock manually
In th eevent of an electrica lfault, it is possible
to release the selector lever lock manually to
move it out of position P,e.g. if you wis hto
tow the vehicle away. X
Depres sthe parkin gbrake firmly.
X Prise ou tselector lever gaiter :with aflat,
blunt object ,(e.g. ascrewdriver wrappe dinclot
h)from th eright-hand edge, pulling it
up and out.
X Pres sreleas ebutton ;dow nand simul-
taneousl ymove the select or lever ou tof
position P.
The selector lever can now be moved freely
unti litisr eturnedtop osition P. Refuelling
Important safet
ynotes G
Risk of explosion
Fuel is highly flammable. Fire, naked flames
and smoking are therefore prohibited when
handling fuels.
Switc hoff the engine before refuelling. G
Ris
kofi njury
Do not com einto contact with fuels. 148
RefuellingDriving and parking
BA 207 ECE ÄJ 2010/1a; 1; 2, en-GB
mkalafa
Version: 3.0.2.11 2010-01-26T13:03:22+01:00-Seite 148

up
aB luetooth ®
connection to th eaudio sys-
tem or COMAN DAPS (see the separate oper-
atin ginstructions). G
Risk of accident
Observe the legal requirements of the country
in which you are currently driving regarding
the use of mobile phones in the vehicle.
If it is permitted to use mobile phones while
the vehicle is in motion, you should only use
them whe nthe roa dand traffic conditions
allo w. Ot herwise, you may be distracte dfrom
th et raffi cconditions, cause an accident and
inj urey oursel fand others.
X Switch on the mobil ephone and audi osys-
tem or COMAND APS (see the separate
operating instructions).
X Press the =or; button on the steer-
ing whee ltoselectthe Tel men u.
Yo uw ills ee on eofthe following display mes-
sage sint he multifunctio ndisplay:
R Please ente rPIN:The mobile phone has
been placed in the mobile phone bracket
and the PIN has not been entered.
X Enter the PIN usin gthe mobile phone, LIN-
GUATRONIC ,the audio system or
COMAN DAPS.
The mobil ephone will search for anetwor k.
In the meantime, the Telephone No
Service displaymessage appears in the
multifunction display.
R Telephon eready or thename of the net-
work provider: the mobile phone has found
an etwor kand is ready to receive.
R No Service:Non etworkisa vail able.
Accepting acall If someone call
syou when you are in the
Tel menu, adisplay message appears in the
multifunction display ,for example: X
Press 6on the steerin gwheel to accept
an incomi ngcall.
You can accep tacall even if you are not in
the Tel menu.
Rejectin gorending acall X
Press the ~buttonont he steering
wheel.
You can end or reject acall even if you are not
in the Telmenu.
Dialling anumbe rfrom the phone book If you
rmobile phone is able to receive calls,
you can search for and dial anumber from the
phone book in the audio system or COMAND
APS at any time.
X Copy the telephone book of the mobile
phone into the audio system or to COMAND
APS (see the separate operating instruc-
tions).
X Press the =or; button on the steer-
ing wheel to select the Telmenu.
X Press the 9,:ora button to call
up the phone book.
X Press 9or: to select the name you
are searching for.
To start scrolling rapidly ,pres sand hol dthe
9 or: button for longer than one
second. After ashort time, the rapid scroll
speeds up.
Rapid scrolling stops when you release the
button or reach the end of the list. Menu
sand submenus
201On-board computer and displays
BA 207ECE ÄJ 2010/1a; 1; 2, en-GB
mkalafa Version: 3.0.2.11 2010-01-26T13:03:22+01:00-Seite 201 Z

Tyres
Display messages Possible caus
es/consequences andM Solutions
Tyre pres‐
sure Check
tyres
G
Ris
kofa ccident
The tyr epressure loss warning system ha sdetected asignif-
ican tloss in pressure.
Aw arning ton ealso sounds.
X Stop th evehicle without making any sudde nsteering or
braking mano euvres.P ay attention to the traffic conditions
as you do so.
X Check the tyres and, if necessary ,change the wheel
(Y page 302).
X Chec kthe tyr epressure and ,ifnecessary, correc tthe tyre
pressure.
X Restart the tyr epressure loss warning system when th etyre
pressure is correct (Y page 301).Check
tyr
epres‐
sures then
restart
Run Flat
Indicator Ad
isplay message for the tyre pressure loss warnin gsystem
was shown.
X Set the cor recttyrep ressur eina ll four tyres.
X Restart th etyrep ressur eloss war ningsystem
(Y page 301). Ru
nF lat
Indicator inopera‐
tive Th
et yrep ressur eloss war ningsystem is faulty.
X Visit aq ualified specialist workshop. Vehicle
Display messages Possible causes/consequences and
M Solutions
To st
art
engine, shift to
either P
or N Yo
uh avea ttempted to startthe engin ewitht he transmiss ion
in position Ror D.
X Shift th etransmission to position Por N. P Select
Park (P) You have switched off the engine with the Star
t/Stop button
and opened the driver's door.
You wante dtolock the vehicle.
Aw arning ton ealso sounds.
X Shift th etransmissio ntoposition P. 230
Display messagesOn-boar
dcomputer and displays
BA 20 7ECE ÄJ 2010/1a; 1; 2, en-GB
mkalafa Version:3.0.2.11
2010-01-26T13:03:22+01:00
-Seite 230