2010 JAGUAR XFR electrical wiring diagrams

Published: 18-Apr-2014
General Information - Diagnostic Trouble Code (DTC) Index DTC: Pedestrian
Protection System Control Module (PPSCM)
Description and Operation

Pedestrian Protection System Control Module (PPSCM)


WARNING: TO AVOID ACCIDENTAL DEPLOYMENT AND POSSIBLE PERSONAL INJURY, THE BACKUP POWER SUPPLY MUST
BE DEPLETED BEFORE REPAIRING OR REPLACING ANY PEDESTRIAN PROTECTION SYSTEM COMPONENTS. TO DEPLETE THE
BACKUP POWER SUPPLY ENERGY, DISCONNECT THE BATTERY GROUND CABLE AND WAIT TWO MINUTES. FAILURE TO FOLLOW
THIS INSTRUCTION MAY RESULT IN PERSONAL INJURY.


CAUTION: Diagnosis by substitution from a donor vehicle is NOT acceptable. Substitution of control modules does not
guarantee confirmation of a fault, and may also cause additional faults in the vehicle being tested and/or the donor vehicle.
NOTES:


If the control module or a component is suspect and the vehicle remains under manufacturer warranty, refer to the
Warranty Policy and Procedures manual, or determine if any prior approval programme is in operation, prior to the installation
of a new module/component.


Generic scan tools may not read the codes listed, or may read only 5-digit codes. Match the 5 digits from the scan tool to
the first 5 digits of the 7-digit code listed to identify the fault (the last 2 digits give extra information read by the
manufacturer-approved diagnostic system).


When performing voltage or resistance tests, always use a digital multimeter accurate to three decimal places, and with
an up-to-date calibration certificate. When testing resistance always take the resistance of the digital multimeter leads into
account.


Check and rectify basic faults before beginning diagnostic routines involving pinpoint tests.


Inspect connectors for signs of water ingress, and pins for damage and/or corrosion.


If DTCs are recorded and, after performing the pinpoint tests, a fault is not present, an intermittent concern may be the
cause. Always check for loose connections and corroded terminals.


Check DDW for open campaigns. Refer to the corresponding bulletins and SSMs which may be valid for the specific
customer complaint and carry out the recommendations as required.

The table below lists all Diagnostic Trouble Codes (DTCs) that could be logged in the Pedestrian Protection System Control
Module (PPSCM). For additional diagnosis and testing information, refer to the relevant Diagnosis and Testing section in the
workshop manual.
For additional information, refer to: Pedestrian Protection System (501-20C Pedestrian Protection System, Diagnosis and Testing).

DTC Description Possible Causes Action B1001-11
Right Hood Deployment
Control - Circuit short to
ground
Right hood deployment
control circuit short circuit
to ground
Refer to the electrical circuit diagrams and
check the right hood deployment control circuit
for short circuit to ground. Install a new wiring
harness as necessary. If no wiring harness
fault exists, using the manufacturer approved
diagnostic system, clear the DTCs and retest.
If the fault persists, install a new right hood
deployment control B1001-12
Right Hood Deployment
Control - Circuit short to
battery
Right hood deployment
control circuit short circuit
to power
Refer to the electrical circuit diagrams and
check the right hood deployment control circuit
for short circuit to power. Install a new wiring
harness as necessary. If no wiring harness
fault exists, using the manufacturer approved
diagnostic system, clear the DTCs and retest.
If the fault persists, install a new right hood
deployment control

Published: 17-Apr-2014
General Information - Diagnostic Trouble Code (DTC) Index DTC: Rear
Differential Control Module (RDCM)
Description and Operation

Rear Differential Control Module (RDCM)


CAUTION: Diagnosis by substitution from a donor vehicle is NOT acceptable. Substitution of control modules does not
guarantee confirmation of a fault, and may also cause additional faults in the vehicle being tested and/or the donor vehicle
NOTES:


If the control module or a component is suspect and the vehicle remains under manufacturer warranty, refer to the
warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation
of a new module/component


Generic scan tools may not read the codes listed, or may read only 5-digit codes. Match the 5 digits from the scan tool to
the first 5 digits of the 7-digit code listed to identify the fault (the last 2 digits give extra information read by the
manufacturer-approved diagnostic system)


When performing voltage or resistance tests, always use a digital multimeter accurate to three decimal places and with a
current calibration certificate. When testing resistance, always take the resistance of the digital multimeter leads into account


Check and rectify basic faults before beginning diagnostic routines involving pinpoint tests


Inspect connectors for signs of water ingress, and pins for damage and/or corrosion


If DTCs are recorded and, after performing the pinpoint tests, a fault is not present, an intermittent concern may be the
cause. Always check for loose connections and corroded terminals


If the rear differential control module, rear differential actuator or the rear differential are replaced, the on demand self
test (ODST) must be carried out to calibrate the components


Check DDW for open campaigns. Refer to the corresponding bulletins and SSMs which may be valid for the specific
customer complaint and carry out the recommendations as needed

The table below lists all diagnostic trouble codes (DTCs) that could be logged in the rear differential control module, for
additional diagnosis and testing information refer to the relevant diagnosis and testing section.
For additional information, refer to: Rear Drive Axle and Differential (205-02 Rear Drive Axle/Differential, Diagnosis and
Testing).

DTC Description Possible Causes Action P0562-00
System Voltage Low -
No sub type
information
Rear differential control
module voltage supply
below 9 volts
Check the battery charge condition, refer to the
electrical circuit diagrams and check the wiring to
the rear differential control module, repair as
necessary P0563-00
System Voltage High -
No sub type
information
System voltage high
(supply voltage supply
greater than 16 volts)
Check engine control module for stored DTCs,
suspect charging system fault. Refer to the
electrical circuit diagrams and check, power and
ground circuit for fault P0604-00
Internal Control Module
Random Access Memory
(RAM) Error - No sub
type information
Rear differential control
module internal error
Clear the DTC and retest. If the problem persists,
renew the control module. Refer to the warranty
policy and procedures manual, or determine if any
prior approval programme is in operation, prior to
the installation of a new module/component P0605-00
Internal Control Module
Read Only Memory
(ROM) Error - No sub
type information
Rear differential control
module internal error
Clear the DTC and retest. If the problem persists,
renew the control module. Refer to the warranty
policy and procedures manual, or determine if any www.JagDocs.com

DTC Description Possible Causes Action P1230-14
Fuel Pump Low Speed
Malfunction (VLCM) -
Circuit short to ground
or open
High Side output not
driven - Diagnosis
feedback indicates
output is short to
ground, open circuit
Refer to the electrical circuit diagrams and check
fuel pump delivery module for short to ground, open
circuit P1230-93
Fuel Pump Low Speed
Malfunction (VLCM) - No
operation
High Side output not
driven - Diagnosis
feedback indicates
output is at open load
or short to power
Carry out any pinpoint test associated with this DTC
using the manufacturer approved diagnostic system.
Refer to the electrical circuit diagrams and check
fuel pump delivery module for short to power, open
circuit P1346-11
Fuel Level Sensor B
Circuit - Circuit short to
ground
Fuel level sensor B
analogue input circuit -
short to ground
Carry out any pinpoint test associated with this DTC
using the manufacturer approved diagnostic system.
Refer to the electrical circuit diagrams and check
fuel level sensor B analogue input circuit for short to
ground P1346-15
Fuel Level Sensor B
Circuit - Circuit short to
battery or open
Fuel level sensor B
analogue input circuit -
short to power, open
circuit
Carry out any pinpoint test associated with this DTC
using the manufacturer approved diagnostic system.
Refer to the electrical circuit diagrams and check
fuel level sensor B analogue input circuit for short to
power, open circuit P1624-13
Anti-theft System -
Circuit open
Anti-theft signal circuit
from CJB - open circuit
Refer to the electrical circuit diagrams and check
anti-theft signal circuit from CJB for open circuit C111A-11
Right Stop Lamp -
Circuit short to ground
Right stomp lamp
control circuit - short to
ground
Carry out any pinpoint test associated with this DTC
using the manufacturer approved diagnostic system.
Refer to the electrical circuit diagrams and check
right stomp lamp control circuit for short to ground C111A-12
Right Stop Lamp -
Circuit short to battery
Right stomp lamp
control circuit - short to
power
Refer to the electrical circuit diagrams and check
right stomp lamp control circuit for short to power C111A-13
Right Stop Lamp -
Circuit open
Right stomp lamp
control circuit - open
circuit
Refer to the electrical circuit diagrams and check
right stomp lamp control circuit for open circuit C111B-11
Left Stop Lamp - Circuit
short to ground
Left stomp lamp control
circuit - short to ground
Carry out any pinpoint test associated with this DTC
using the manufacturer approved diagnostic system.
Refer to the electrical circuit diagrams and check left
stomp lamp control circuit for short to ground C111B-13
Left Stop Lamp - Circuit
open
Left stomp lamp control
circuit - open circuit
Refer to the electrical circuit diagrams and check left
stomp lamp control circuit for open circuit C1120-11
Reversing lamp - Circuit
short to ground
Reverse lamp control
circuit - short to ground
Carry out any pinpoint test associated with this DTC
using the manufacturer approved diagnostic system.
Refer to the electrical circuit diagrams and check
reverse lamp control circuit for short to ground C1120-12
Reversing lamp - Circuit
short to battery
Reverse lamp control
circuit - short to power
Refer to the electrical circuit diagrams and check
reverse lamp control circuit for short to power C1120-13
Reversing lamp - Circuit
open
Reverse lamp control
circuit - open circuit
Refer to the electrical circuit diagrams and check
reverse lamp control circuit for open circuit C1120-15
Reversing lamp - Circuit
short to battery or open
Reverse lamp control
circuit - short circuit to
power, open circuit, high
resistance
Refer to the electrical circuit diagrams and check
reverse lamp control circuit for short circuit to power,
open circuit, high resistance. Repair wiring harness
as required. Clear DTC and retest

DTC Description Possible Causes Action B111A-12
Number Plate Lamps -
Circuit short to battery
Right hand or left hand
number plate lamp
control circuits - short to
power
Refer to the electrical circuit diagrams and check
right hand and left hand number plate lamp control
circuits for short to power B111A-13
Number Plate Lamps -
Circuit open
Right hand or left hand
number plate lamp
control circuits - open
circuit
Refer to the electrical circuit diagrams and check
right hand and left hand number plate lamp control
circuits for open circuit B111A-15
Number Plate Lamps -
Circuit short to battery
or open
Right or left side licence
plate lamp(s)
inoperative
Right or left side licence
plate lamp control
circuits - short circuit to
power, open circuit, high
resistance
Refer to the electrical circuit diagrams and check
right side and left side licence plate lamp control
circuits for short circuit to power, open circuit, high
resistance. Repair wiring harness as required. Clear
DTC and retest B111D-12
Boot/Trunk Motor Open -
Circuit short to battery
Luggage compartment
lid latch actuator control
circuit - short to power
Carry out any pinpoint test associated with this DTC
using the manufacturer approved diagnostic system.
Refer to the electrical circuit diagrams and check
luggage compartment lid latch actuator control
circuit for short to power B111D-14
Boot/Trunk Motor Open -
Circuit short to ground
or open
Luggage compartment
lid latch actuator control
circuit - short to ground,
open circuit
Carry out any pinpoint test associated with this DTC
using the manufacturer approved diagnostic system.
Refer to the electrical circuit diagrams and check
luggage compartment lid latch actuator control
circuit for short to ground, open circuit B111E-11
Boot/Trunk Lamps -
Circuit short to ground
Luggage compartment
lamp control circuit -
short to ground
Carry out any pinpoint test associated with this DTC
using the manufacturer approved diagnostic system.
Refer to the electrical circuit diagrams and check
luggage compartment lamp control circuit for short
to ground B111E-12
Boot/Trunk Lamps -
Circuit short to battery
Luggage compartment
lamp control circuit -
short to power
Refer to the electrical circuit diagrams and check
luggage compartment lamp control circuit for short
to power B111E-13
Boot/Trunk Lamps -
Circuit open
Luggage compartment
lamp control circuit -
open circuit
Refer to the electrical circuit diagrams and check
luggage compartment lamp control circuit for open
circuit B111E-15
Boot/Trunk Lamps -
Circuit short to battery
or open
Luggage compartment
lamp inoperative
Luggage compartment
lamp control circuit -
short circuit to power,
open circuit, high
resistance
Refer to the electrical circuit diagrams and check
luggage compartment lamp control circuit for short
circuit to power, open circuit, high resistance. Repair
wiring harness as required. Clear DTC and retest B1123-12
Restraints Ignition
Relay - Circuit short to
battery
High Side output not
driven - diagnosis
feedback indicates
output is short to power
Carry out any pinpoint test associated with this DTC
using the manufacturer approved diagnostic system.
Refer to the electrical circuit diagrams and check
restraints ignition relay output for short to power B1123-14
Restraints Ignition
Relay - Circuit short to
ground or open
High Side output not
driven - diagnosis
feedback indicates
output is short to
ground, open circuit
Carry out any pinpoint test associated with this DTC
using the manufacturer approved diagnostic system.
Refer to the electrical circuit diagrams and check
restraints ignition relay output for short to ground,
open circuit B1123-93
Restraints Ignition
Relay - No operation
High Side output not
driven - diagnosis
feedback indicates
output is at open load
Carry out any pinpoint test associated with this DTC
using the manufacturer approved diagnostic system.
Refer to the electrical circuit diagrams and check
restraints ignition relay output for open load or

DTC Description Possible Causes Action B123A-13 Left Front Turn Indicator
- Circuit open
Left front turn signal
lamp control circuit -
open circuit
Refer to the electrical circuit diagrams and check left
front turn signal lamp control circuit for open circuit B123A-15 Left Front Turn Indicator
- Circuit short to battery
or open
Left front turn signal
lamp control circuit -
short circuit to power,
open circuit, high
resistance
Refer to electrical circuit diagrams and check left
front turn signal lamp control circuit for short circuit
to power, open circuit, high resistance. Repair wiring
harness as required. Clear DTC and retest B123B-11
Right Front Turn
Indicator - Circuit short
to ground
Right front turn signal
lamp control circuit -
short to ground
Refer to the electrical circuit diagrams and check
right front turn signal lamp control circuit for short
to ground B123B-12
Right Front Turn
Indicator - Circuit short
to battery
Right front turn signal
lamp control circuit -
short to power
Refer to the electrical circuit diagrams and check
right front turn signal lamp control circuit for short
to power B123B-13
Right Front Turn
Indicator - Circuit open
Right front turn signal
lamp control circuit -
open circuit
Refer to the electrical circuit diagrams and check
right front turn signal lamp control circuit for open
circuit B123B-15
Right Front Turn
Indicator - Circuit short
to battery or open
Right front turn signal
lamp control circuit -
short circuit to power,
open circuit, high
resistance
Refer to electrical circuit diagrams and check right
front turn signal lamp control circuit for short circuit
to power, open circuit, high resistance. Repair wiring
harness as required. Clear DTC and retest B1247-11 Left Rear Turn Indicator
- Circuit short to ground
Left rear turn signal
lamp control circuit -
short to ground
Refer to the electrical circuit diagrams and check left
rear turn signal lamp control circuit for short to
ground B1247-12 Left Rear Turn Indicator
- Circuit short to battery
Left rear turn signal
lamp control circuit -
short to power
Refer to the electrical circuit diagrams and check left
rear turn signal lamp control circuit for short to
power B1247-13 Left Rear Turn Indicator
- Circuit open
Left rear turn signal
lamp control circuit -
short to power, open
circuit
Refer to the electrical circuit diagrams and check left
rear turn signal lamp control circuit for open circuit B1247-15 Left Rear Turn Indicator
- Circuit short to battery
or open
Left rear turn signal
lamp control circuit -
short circuit to power,
open circuit, high
resistance
Refer to electrical circuit diagrams and check left
rear turn signal lamp control circuit for short circuit
to power, open circuit, high resistance. Repair wiring
harness as required. Clear DTC and retest B1248-11
Right Rear Turn
Indicator - Circuit short
to ground
Right rear turn signal
lamp control circuit -
short to ground
Refer to the electrical circuit diagrams and check
right rear turn signal lamp control circuit for short to
ground B1248-12
Right Rear Turn
Indicator - Circuit short
to battery
Right rear turn signal
lamp control circuit -
short to power
Refer to the electrical circuit diagrams and check
right rear turn signal lamp control circuit for short to
power B1248-13
Right Rear Turn
Indicator - Circuit open
Right rear turn signal
lamp control circuit -
open circuit
Refer to the electrical circuit diagrams and check
right rear turn signal lamp control circuit for open
circuit B1248-15
Right Rear Turn
Indicator - Circuit short
to battery or open
Right rear turn signal
lamp control circuit -
short circuit to power,
open circuit, high
resistance
Refer to electrical circuit diagrams and check right
rear turn signal lamp control circuit for short circuit
to power, open circuit, high resistance. Repair wiring
harness as required. Clear DTC and retest

Published: 18-Apr-2014
General Information - Diagnostic Trouble Code (DTC) Index DTC: Remote
Keyless Entry Module (RFA)
Description and Operation

Remote Keyless Entry Module (RFA)

CAUTIONS:


Diagnosis by substitution from a donor vehicle is NOT acceptable. Substitution of control modules does not guarantee
confirmation of a fault, and may also cause additional faults in the vehicle being tested and/or the donor vehicle


When probing connectors to take measurements in the course of the pinpoint tests, use the adaptor kit, part number
3548-1358-00
NOTES:


If the control module or a component is suspect and the vehicle remains under manufacturer warranty, refer to the
warranty policy and procedures manual (section B1.2), or determine if any prior approval programme is in operation, prior to
the installation of a new module/component


Generic scan tools may not read the codes listed, or may read only 5-digit codes. Match the 5 digits from the scan tool to
the first 5 digits of the 7-digit code listed to identify the fault (the last 2 digits give extra information read by the
manufacturer-approved diagnostic system)


When performing voltage or resistance tests, always use a digital multimeter accurate to three decimal places and with a
current calibration certificate. When testing resistance, always take the resistance of the digital multimeter leads into account


Check and rectify basic faults before beginning diagnostic routines involving pinpoint tests


Inspect connectors for signs of water ingress, and pins for damage and/or corrosion


If diagnostic trouble codes are recorded and, after performing the pinpoint tests, a fault is not present, an intermittent
concern may be the cause. Always check for loose connections and corroded terminals


Where an 'on demand self-test' is referred to, this can be accessed via the 'diagnostic trouble code monitor' tab on the
manufacturers approved diagnostic system

The table below lists all diagnostic trouble codes (DTCs) that could be logged in the remote keyless entry module, for
additional diagnosis and testing information refer to the relevant diagnosis and testing section.
For additional information, refer to: Remote Keyless Entry (RKE) Module (419-10 Multifunction Electronic Modules, Diagnosis
and Testing).

DTC Description Possible Causes Action B102B-00
Passive Key - No sub
type information
Response Error - general
failure
Using the manufacturer approved diagnostic
system, clear all passive keys, re-learn all passive
keys B10C1-00
Left Front Unlock Pull
Switch - No sub type
information
No power supply to door
handle
Switch circuit open, or
short circuit to power
Carry out any pinpoint tests associated with this
DTC using the manufacturer approved diagnostic
system. Refer to the electrical circuit diagrams and
check the power supply to the door handle. Check
the switch circuit is not open circuit or short to
power. Repair wiring as required B10C1-24
Left Front Unlock Pull
Switch - Signal stuck
high
Signal stuck high - button
stuck in active position
Carry out any pinpoint tests associated with this
DTC using the manufacturer approved diagnostic
system. Check for stuck left front unlock switch.
Refer to the electrical circuit diagrams and check
left front unlock switch circuit for short to ground

DTC Description Possible Causes Action B10C2-00
Left Rear Unlock Pull
Switch - No sub type
information
No power supply to door
handle
Switch circuit open, or
short circuit to power
Carry out any pinpoint tests associated with this
DTC using the manufacturer approved diagnostic
system. Refer to the electrical circuit diagrams and
check the power supply to the door handle. Check
the switch circuit is not open circuit or short to
power. Repair wiring as required B10C2-24
Left Rear Unlock Pull
Switch - Signal stuck
high
Signal stuck high - button
stuck in active position
Carry out any pinpoint tests associated with this
DTC using the manufacturer approved diagnostic
system. Check for stuck left rear unlock switch.
Refer to the electrical circuit diagrams and check
left rear unlock switch circuit for short to ground B10C3-00
Right Front Unlock Pull
Switch - No sub type
information
No power supply to door
handle
Switch circuit open, or
short circuit to power
Carry out any pinpoint tests associated with this
DTC using the manufacturer approved diagnostic
system. Refer to the electrical circuit diagrams and
check the power supply to the door handle. Check
the switch circuit is not open circuit or short to
power. Repair wiring as required B10C3-24
Right Front Unlock Pull
Switch - Signal stuck
high
Signal stuck high - button
stuck in active position
Carry out any pinpoint tests associated with this
DTC using the manufacturer approved diagnostic
system. Check for stuck right front unlock switch.
Refer to the electrical circuit diagrams and check
right front unlock switch circuit for short to ground B10C4-00
Right Rear Unlock Pull
Switch - No sub type
information
No power supply to door
handle
Switch circuit open, or
short circuit to power
Carry out any pinpoint tests associated with this
DTC using the manufacturer approved diagnostic
system. Refer to the electrical circuit diagrams and
check the power supply to the door handle. Check
the switch circuit is not open circuit or short to
power. Repair wiring as required B10C4-24
Right Rear Unlock Pull
Switch - Signal stuck
high
Signal stuck high - button
stuck in active position
Carry out any pinpoint tests associated with this
DTC using the manufacturer approved diagnostic
system. Check for stuck right rear unlock switch.
Refer to the electrical circuit diagrams and check
right front unlock switch circuit for short to ground B10C5-24 Trunk Unlock Pull
Switch - Signal stuck
high
Signal stuck high - button
stuck in active position
Carry out any pinpoint tests associated with this
DTC using the manufacturer approved diagnostic
system. Check for stuck luggage compartment lid
unlock switch. Refer to the electrical circuit diagrams
and check luggage compartment lid unlock
switch circuit for short to ground B10C6-1F Exterior Trunk Antenna
- Circuit intermittent
Circuit intermittent -
general electrical error
Carry out any pinpoint tests associated with this
DTC using the manufacturer approved diagnostic
system. Refer to the electrical circuit diagrams and
check exterior luggage compartment antenna
circuits for short to ground, power, open circuit B10C7-1F Interior Trunk Antenna
- Circuit intermittent
Circuit intermittent -
general electrical error
Carry out any pinpoint tests associated with this
DTC using the manufacturer approved diagnostic
system. Refer to the electrical circuit diagrams and
check interior luggage compartment antenna circuits
for short to ground, power, open circuit B10C8-1F
Interior Center
Antenna - Circuit
intermittent
Circuit intermittent -
general electrical error
Carry out any pinpoint tests associated with this
DTC using the manufacturer approved diagnostic
system. Refer to the electrical circuit diagrams and
check interior center antenna circuits for short to
ground, power, open circuit B10C9-1F Interior Front Antenna
- Circuit intermittent
Circuit intermittent -
general electrical error
Carry out any pinpoint tests associated with this
DTC using the manufacturer approved diagnostic
system. Refer to the electrical circuit diagrams and
check interior front antenna circuits for short to

Published: 17-Apr-2014
General Information - Diagnostic Trouble Code (DTC) Index DTC: Satellite
Digital Audio Radio System Module (SARM)
Description and Operation

Satellite Radio Module (SARM)


CAUTION: Diagnosis by substitution from a donor vehicle is NOT acceptable. Substitution of control modules does not
guarantee confirmation of a fault, and may also cause additional faults in the vehicle being tested and/or the donor vehicle
NOTES:


If the control module or a component is suspect and the vehicle remains under manufacturer warranty, refer to the
warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation
of a new module/component


Generic scan tools may not read the codes listed, or may read only 5-digit codes. Match the 5 digits from the scan tool to
the first 5 digits of the 7-digit code listed to identify the fault (the last 2 digits give extra information read by the
manufacturer-approved diagnostic system)


When performing voltage or resistance tests, always use a digital multimeter accurate to three decimal places and with a
current calibration certificate. When testing resistance, always take the resistance of the digital multimeter leads into account


Check and rectify basic faults before beginning diagnostic routines involving pinpoint tests


Inspect connectors for signs of water ingress, and pins for damage and/or corrosion


If diagnostic trouble codes are recorded and, after performing the pinpoint tests, a fault is not present, an intermittent
concern may be the cause. Always check for loose connections and corroded terminals


Where an 'on demand self-test' is referred to, this can be accessed via the 'diagnostic trouble code monitor' tab on the
manufacturers approved diagnostic system


Check DDW for open campaigns. Refer to the corresponding bulletins and SSMs which may be valid for the specific
customer complaint and carry out the recommendations as needed

The table below lists all diagnostic trouble codes (DTCs) that could be logged on the satellite radio module, for additional
diagnosis and testing information refer to the relevant diagnosis and testing section.
For additional information, refer to: Information and Entertainment System (415-00 Information and Entertainment System -
General Information, Diagnosis and Testing).

DTC Description Possible Causes Action B1A89-01
Satellite Antenna -
General electrical
failure
Wiring harness fault -
Coaxial cable between
satellite radio module and
the satellite antenna
Internal electronic failure
- Satellite digital audio
radio antenna
Internal electronic failure
- Satellite radio module
Refer to the electrical circuit diagrams and check
satellite digital audio radio antenna coaxial cable for
short circuit to ground, short circuit to power, open
circuit, high resistance. Repair wiring harness as
required, clear DTC and retest
If fault persists, check and install a new satellite digital
audio radio antenna
If fault persists, check and install a new satellite radio
module
Refer to the warranty policy and procedures manual, or
determine if any prior approval programme is in
operation, prior to the installation of a new
module/component B1A89-11
Satellite Antenna -
Circuit short to
ground
Satellite antenna circuit -
short to ground
Refer to the electrical circuit diagrams and check
satellite antenna circuit for short circuit to ground.
Repair wiring harness as required. Clear DTC and retest www.JagDocs.com