2010 JAGUAR XFR ignition

DTC Description Possible Causes Action U3000-04
Control Module -
System Internal
Failures
Occupancy seat module
internal electronic failure
Check and install a new occupancy seat module as
required. Refer to the warranty policy and procedures
manual, or determine if any prior approval programme is
in operation, prior to the installation of a new
module/component U3000-54
Control Module -
Missing calibration
This diagnostic trouble
code is set if a 'calibrate
occupancy seat module
empty seat offset'
routine is requested and
fails due to one of the
pre-conditions to
execute the routine
Check the following criteria have all been achieved:
Ignition status set to RUN/START. Verify seat is always
empty after power-up before re-zero is requested. The
occupancy seat module has gone through the seat
assembly plant calibration. No collision event received
from the restraints control module during the current
ignition cycle. No faults present in the current ignition
cycle. The trigger message for calibrate empty seat
offset has been received from the diagnostic tool.
Occupancy seat module has enough time to begin
classification. Temperature is between 6C (42F) and 36C
(97F) U3003-16
Battery Voltage -
Circuit voltage
below threshold
Circuit voltage below
threshold
Check battery is in fully charged and serviceable
condition. Check integrity of charging system U3003-17
Battery Voltage -
Circuit voltage
above threshold
Circuit voltage above
threshold
Check battery is in fully charged and serviceable
condition. Check integrity of charging system

DTC Description Possible Causes Action Cycle the ignition off, then on, to power up parking
aid system and check corrective action B1B58-11
Rear Sensors Power
Circuit - Circuit short
to ground
Wiring harness fault
Control Module -
Component internal
failure
Check rear and front (if front PDC fitted) bumper
harness for signs of damage and security of
connections
Refer to electrical wiring diagrams and check the
parking assist rear sensor power circuit and front
sensor power circuit (if front PDC fitted) for short
circuit to ground. Repair or replace any wiring harness
as required
Using the manufacturers approved diagnostic system
clear the DTC and run the on demand self test. If the
problem persists, suspect the control module
Cycle the ignition off, then on, to power up parking
aid system and check corrective action B1C30-73
Disable Switch -
Actuator stuck closed
Wiring harness fault
Control Switch -
Component internal
failure
Refer to electrical wiring diagrams and check the
parking assist switch and switch circuit. Repair or
replace any wiring harness as required
Using the manufacturers approved diagnostic system
clear the DTC and run the on demand self test. If the
problem persists, suspect the control switch
Check the switch function U0010-00
Medium Speed CAN
Communication Bus -
No sub type
information
Medium speed CAN
failure - bus off
Refer to the electrical circuit diagrams and check the
parking aid control module medium speed CAN bus
for short circuit to ground, short circuit to power,
open circuit, high resistance, or short circuit between
the paired CAN wires
Using the manufacturer approved diagnostic system,
complete a CAN network integrity test
Cycle the ignition off, then on, and check if the DTC
is still logged U0073-00
Control Module
Communication Bus
"A" Off - No sub type
information
Control module
communication Bus "A"
failure - bus off
Refer to the electrical circuit diagrams and check the
parking aid control module high speed CAN bus for
short circuit to ground, short circuit to power, open
circuit, high resistance, or short circuit between the
paired CAN wires
Using the manufacturer approved diagnostic system,
complete a CAN network integrity test
Cycle the ignition off, then on, and check if the DTC
is still logged U0140-00
Lost Communication
With Body Control
Module - No sub type
information
Loss of CAN
communication with
central junction box
Refer to the electrical circuit diagrams and check the
power and ground connections to the central junction
box. Clear DTC and retest
Using the manufacturer approved diagnostic system,
complete a CAN network integrity test. Refer to the
electrical circuit diagrams and check the CAN network
between the central junction box and the parking aid
control module U0142-00 Lost Communication
Loss of CAN
Refer to the electrical circuit diagrams and check the With Body Control Module "B" - No sub communication with power and ground connections to the auxiliary type information auxiliary junction box junction box. Clear DTC and retest Using the manufacturer approved diagnostic system, complete a CAN network integrity test. Refer to the electrical circuit diagrams and check the CAN network between the central junction box and the parking aid control module U0155-00
Lost Communication
With Instrument Panel
Cluster (IPC) Control
Module - No sub type
information
Loss of CAN
communication with
instrument cluster
Refer to the electrical circuit diagrams and check the
power and ground connections to the instrument
cluster. Clear DTC and retest
Using the manufacturer approved diagnostic system,
complete a CAN network integrity test. Refer to the
electrical circuit diagrams and check the CAN network
between the central junction box and the parking aid
control module

DTC Description Possible Causes Action U0300-00
Internal Control
Module Software
Incompatibility - No
sub type information
Car configuration file
stored in parking aid
control module does not
match the master car
configuration file
Master car configuration
file not being
transmitted by master
control module
Using the manufacturer approved diagnostic system,
check all other control modules, for related DTCs and
refer to the relevant DTC index
Check the components installed on the vehicle were
installed by the factory or a dealer
Install the original component or a new one as
required U0422-00
Invalid Data Received
From Body Control
Module - No sub type
information
Invalid data received
Using the manufacturer approved diagnostic system,
check central junction box, for related DTCs and refer
to the relevant DTC index
Using the manufacturer approved diagnostic system,
complete a CAN network integrity test
Cycle the ignition off, then on, and check if the DTC
is still logged
Clear the DTC and re-test U0423-00
Invalid Data Received
From Instrument Panel
Control Module - No
sub type information
Invalid data received
Using the manufacturer approved diagnostic system,
check instrument cluster, for related DTCs and refer
to the relevant DTC index
Using the manufacturer approved diagnostic system,
complete a CAN network integrity test
Cycle the ignition off, then on, and check if the DTC
is still logged
Clear the DTC and re-test U0443-00
Invalid Data Received
From Body Control
Module "B" - No sub
type information
Invalid data received
Using the manufacturer approved diagnostic system,
check auxiliary junction box, for related DTCs and
refer to the relevant DTC index
Using the manufacturer approved diagnostic system,
complete a CAN network integrity test
Cycle the ignition off, then on, and check if the DTC
is still logged
Clear the DTC and re-test U2100-00
Initial Configuration
Not Complete - No sub
type information
Car configuration file not
the same as expected by
the parking aid control
module
NOTE: After updating the car configuration file, set the
ignition to on and wait 30 seconds before clearing the DTCs

Using the manufacturer approved diagnostic system,
check and update the car configuration file as
required. Clear the DTC and retest U2101-00
Control Module
Configuration
Incompatible - No sub
type information
Parking aid control
module configuration
error
Using the manufacturer approved diagnostic system
check and up-date the car configuration file as
required. Clear the DTC and re-test U3000-49
Control Module -
Internal electronic
failure
Parking aid control
module internal failure
Using the manufacturers approved diagnostic system
clear the DTC, cycle the ignition off, then on, and
check if the DTC is still logged
If the DTC is still logged suspect the parking aid
control module U3002-81
Vehicle Identification
Number - Invalid serial
data received
VIN Mismatch, stored
VIN does not match
broadcast VIN
Using the manufacturers approved diagnostic system
clear the DTC, cycle the ignition off, then on, and
check if the DTC is still logged
If the DTC is still logged replace the parking aid
control module U3003-16
Battery voltage -
Circuit voltage below
threshold
Circuit voltage below
threshold
Using the manufacturer approved diagnostic system,
check central junction box, for related DTCs and refer
to the relevant DTC index
Check the vehicle charging system performance to
ensure the voltage regulation is correct
Refer to relevant section of workshop manual and
battery care manual. Check battery state of charge
and starting/charging system performance
Refer to the electrical circuit diagrams and check
parking aid control module power and ground circuits

DTC Description Possible Causes Action B10AF-93
Blower Fan Relay - No
operation
High Side output not
driven - Diagnosis
feedback indicates
output is at open load
or short to power
Carry out any pinpoint test associated with this DTC
using the manufacturer approved diagnostic system.
Refer to the electrical circuit diagrams and check
blower motor supply circuit for short to power, open
circuit B10DD-11
Airbag Deployed -
Circuit short to ground
Airbag deployed digital
input signal circuit -
short to ground
Carry out any pinpoint test associated with this DTC
using the manufacturer approved diagnostic system.
Refer to the electrical circuit diagrams and check
airbag deployed digital input signal circuit for short
to ground B10DD-15
Airbag Deployed -
Circuit short to battery
or open
Airbag deployed digital
input signal circuit -
short to power, open
circuit
Carry out any pinpoint test associated with this DTC
using the manufacturer approved diagnostic system.
Refer to the electrical circuit diagrams and check
airbag deployed digital input signal circuit for short
to power, open circuit B10DD-38
Airbag Deployed - Signal
frequency incorrect
Signal frequency
incorrect
Check the RCM for related DTCs and refer to the
relevant DTC Index B10DE-11
Low Fuel Warning
Switch - Circuit short to
ground
Diesel run-dry switch
analogue input circuit -
short to ground
Carry out any pinpoint test associated with this DTC
using the manufacturer approved diagnostic system.
Refer to the electrical circuit diagrams and check
diesel run-dry switch analogue input circuit for short
to ground B10DE-15
Low Fuel Warning
Switch - Circuit short to
battery or open
Diesel run-dry switch
analogue input circuit -
short to power, open
circuit
Carry out any pinpoint test associated with this DTC
using the manufacturer approved diagnostic system.
Refer to the electrical circuit diagrams and check
diesel run-dry switch analogue input circuit for short
to power, open circuit B1112-11
Park Aid Ignition -
Circuit short to ground
Parking aid ignition
supply circuit - short to
ground
Carry out any pinpoint test associated with this DTC
using the manufacturer approved diagnostic system.
Refer to the electrical circuit diagrams and check
parking aid ignition supply circuit for short to ground B1112-12
Park Aid Ignition -
Circuit short to battery
Parking aid ignition
supply circuit - short to
power
Refer to the electrical circuit diagrams and check
parking aid ignition supply circuit for short to power B1115-11
High Mounted Stop
Lamp Control - Circuit
short to ground
High mounted stop lamp
control circuit - short to
ground
Carry out any pinpoint test associated with this DTC
using the manufacturer approved diagnostic system.
Refer to the electrical circuit diagrams and check
high mounted stop lamp control circuit for short to
ground B1116-11
Left Tail Lamp - Circuit
short to ground
Left hand tail lamp
control circuit - short to
ground
Carry out any pinpoint test associated with this DTC
using the manufacturer approved diagnostic system.
Refer to the electrical circuit diagrams and check left
hand tail lamp control circuit for short to ground B1117-11
Right Tail Lamp - Circuit
short to ground
Right hand tail lamp
control circuit - short to
ground
Carry out any pinpoint test associated with this DTC
using the manufacturer approved diagnostic system.
Refer to the electrical circuit diagrams and check
right hand tail lamp control circuit for short to
ground B111A-11
Number Plate Lamps -
Circuit short to ground
Right hand or left hand
number plate lamp
control circuits - short to
ground
Carry out any pinpoint test associated with this DTC
using the manufacturer approved diagnostic system.
Refer to the electrical circuit diagrams and check
right hand and left hand number plate lamp control
circuits for short to ground www.JagDocs.com

DTC Description Possible Causes Action B111A-12
Number Plate Lamps -
Circuit short to battery
Right hand or left hand
number plate lamp
control circuits - short to
power
Refer to the electrical circuit diagrams and check
right hand and left hand number plate lamp control
circuits for short to power B111A-13
Number Plate Lamps -
Circuit open
Right hand or left hand
number plate lamp
control circuits - open
circuit
Refer to the electrical circuit diagrams and check
right hand and left hand number plate lamp control
circuits for open circuit B111A-15
Number Plate Lamps -
Circuit short to battery
or open
Right or left side licence
plate lamp(s)
inoperative
Right or left side licence
plate lamp control
circuits - short circuit to
power, open circuit, high
resistance
Refer to the electrical circuit diagrams and check
right side and left side licence plate lamp control
circuits for short circuit to power, open circuit, high
resistance. Repair wiring harness as required. Clear
DTC and retest B111D-12
Boot/Trunk Motor Open -
Circuit short to battery
Luggage compartment
lid latch actuator control
circuit - short to power
Carry out any pinpoint test associated with this DTC
using the manufacturer approved diagnostic system.
Refer to the electrical circuit diagrams and check
luggage compartment lid latch actuator control
circuit for short to power B111D-14
Boot/Trunk Motor Open -
Circuit short to ground
or open
Luggage compartment
lid latch actuator control
circuit - short to ground,
open circuit
Carry out any pinpoint test associated with this DTC
using the manufacturer approved diagnostic system.
Refer to the electrical circuit diagrams and check
luggage compartment lid latch actuator control
circuit for short to ground, open circuit B111E-11
Boot/Trunk Lamps -
Circuit short to ground
Luggage compartment
lamp control circuit -
short to ground
Carry out any pinpoint test associated with this DTC
using the manufacturer approved diagnostic system.
Refer to the electrical circuit diagrams and check
luggage compartment lamp control circuit for short
to ground B111E-12
Boot/Trunk Lamps -
Circuit short to battery
Luggage compartment
lamp control circuit -
short to power
Refer to the electrical circuit diagrams and check
luggage compartment lamp control circuit for short
to power B111E-13
Boot/Trunk Lamps -
Circuit open
Luggage compartment
lamp control circuit -
open circuit
Refer to the electrical circuit diagrams and check
luggage compartment lamp control circuit for open
circuit B111E-15
Boot/Trunk Lamps -
Circuit short to battery
or open
Luggage compartment
lamp inoperative
Luggage compartment
lamp control circuit -
short circuit to power,
open circuit, high
resistance
Refer to the electrical circuit diagrams and check
luggage compartment lamp control circuit for short
circuit to power, open circuit, high resistance. Repair
wiring harness as required. Clear DTC and retest B1123-12
Restraints Ignition
Relay - Circuit short to
battery
High Side output not
driven - diagnosis
feedback indicates
output is short to power
Carry out any pinpoint test associated with this DTC
using the manufacturer approved diagnostic system.
Refer to the electrical circuit diagrams and check
restraints ignition relay output for short to power B1123-14
Restraints Ignition
Relay - Circuit short to
ground or open
High Side output not
driven - diagnosis
feedback indicates
output is short to
ground, open circuit
Carry out any pinpoint test associated with this DTC
using the manufacturer approved diagnostic system.
Refer to the electrical circuit diagrams and check
restraints ignition relay output for short to ground,
open circuit B1123-93
Restraints Ignition
Relay - No operation
High Side output not
driven - diagnosis
feedback indicates
output is at open load
Carry out any pinpoint test associated with this DTC
using the manufacturer approved diagnostic system.
Refer to the electrical circuit diagrams and check
restraints ignition relay output for open load or

DTC Description Possible Causes Action B1087-83
LIN Bus "A" - Value
of signal protection
calculation
incorrect
Transmission control module LIN
message error - checksum fault
Refer to the electrical circuit diagrams and
check LIN input signal circuit for short circuit
to ground, short circuit to power, open
circuit, high resistance. Check transmission
control module for related DTCs and refer to
relevant DTC index B1087-87 LIN Bus "A" -
Missing message
Transmission control module LIN
message error - Missing message
Refer to the electrical circuit diagrams and
check LIN input signal circuit for short circuit
to ground, short circuit to power, open
circuit, high resistance. Check transmission
control module for related DTCs and refer to
relevant DTC index B1142-62
Ignition Status 1 -
Signal compare
failure
Hardwired ignition and CAN
powermode signals differ
Refer to the electrical circuit diagrams and
check ignition supply circuit for short circuit
to ground, short circuit to power, open
circuit, high resistance B123C-01
Dynamic Stability
Control Status
Indicator - General
Electrical Failure
Dynamic stability control LED failure
Check transmission shift module, check
operation of the dynamic stability control
button status illumination, check and install
new transmission shift module as required.
Refer to the warranty policy and procedures
manual, or determine if any prior approval
programme is in operation, prior to the
installation of a new module B123D-64
Dynamic Stability
Control Button -
Signal plausibility
failure
Dynamic stability control button may
be stuck, may be due to a faulty
button or to the user holding the
button for a prolonged period
(dynamic stability control button
detected as pressed for 30 seconds)
(S1)
Check for normal dynamic stability control
button functionality. If it operates normally
then no further action required. If the
dynamic stability control button fails to
operate normally then may be due to an
internal fault, check and install new
transmission shift module as required. Refer
to the warranty policy and procedures
manual, or determine if any prior approval
programme is in operation, prior to the
installation of a new module B123F-01
Adaptive Speed
Limiter Mode
Indicator - General
Electrical Failure
Adaptive speed limiter LED failure
Check transmission shift module, check
operation of the active speed limiter button
status illumination, check and install new
transmission shift module as required. Refer
to the warranty policy and procedures
manual, or determine if any prior approval
programme is in operation, prior to the
installation of a new module B1241-64
Adaptive Speed
Limiter Button -
Signal plausibility
failure
May be due to a faulty button or to
the user holding the button for a
prolonged period (adaptive speed
limiter button detected as pressed
for 30 seconds)
Check for normal adaptive speed limiter
button functionality. If it operates normally
then no further action required. If the
adaptive speed limiter button fails to
operate normally then may be due to an
internal fault, check and install new
transmission shift module as required. Refer
to the warranty policy and procedures
manual, or determine if any prior approval
programme is in operation, prior to the
installation of a new module B1242-64
Winter Button -
Signal plausibility
failure
May be due to a faulty button or to
the user holding the button for a
prolonged period (winter button
detected as pressed for 30 seconds)
Check for normal winter button functionality.
If it operates normally then no further action
required. If the winter button fails to operate
normally then may be due to an
internal fault, check and install new
transmission shift module as required. Refer
to the warranty policy and procedures
manual, or determine if any prior approval
programme is in operation, prior to the
installation of a new module www.JagDocs.com

Rear Suspended Tow


When the vehicle is being recovered by rear suspended tow:

The ignition key must be removed from the ignition switch to lock the steering.
The rear wheels must be correctly positioned in the lifting cradle and securely tied down.
Emergency Towing


WARNING: If the engine is not running, the steering will become heavy and the force necessary to effectively apply the
brakes will be greatly increased.


CAUTION: A vehicle with a defective transmission must be towed by rear suspended tow.
When the vehicle is being towed on its own wheels:

Local regulations for the towing of vehicles must be followed. In some countries the registration number of the towing
vehicle and an 'On Tow' sign or warning triangle must be displayed at the rear of the towed vehicle.
The gear selector lever must be in Neutral.
The ignition switch must be in position II to release the steering lock and make the direction indicators, horn and stop
lamps operate.
A distance of 0,8 km (0.5 mile) must not be exceeded.
A speed of 48 km/h (30 mph) must not be exceeded.
The tow rope must be attached to the front towing eye. www.JagDocs.com

The warning indications to the driver are common on all vehicles fitted with TPMS. The driver is alerted to system warnings by
a low tire pressure warning indicator in the instrument cluster and an applicable text message in the message centre.

The TPMS module passes system status information to the instrument cluster on the medium speed CAN bus. The instrument
cluster converts this data into illumination of the warning indicator and the display of an appropriate message.
When the ignition is switched on, the warning indicator is illuminated for 3 seconds for a bulb check.


NOTE: If the vehicle is not fitted with the TPMS, the warning indicator will not illuminate.

The instrument cluster checks, within the 3 second bulb check period, for a CAN bus message from the TPMS. During this time
the TPMS performs internal tests and CAN bus initialization. The warning indicator will be extinguished if the TPMS module
does not issue a fault message or tire pressure warning message.

If a TPMS fault warning message is detected by the instrument cluster at ignition on, the warning indicator will flash for 72
seconds after the 3 second bulb check period and then remain permanently illuminated.

If a tire pressure warning message is detected by the instrument cluster at ignition on, the warning indicator will extinguish
briefly after the 3 second bulb check period, before re-illuminating to indicate a tire pressure warning.
The following table shows the warning indicator functionality for given events:

Event Instrument Cluster Indications Low pressure warning limit reached in one wheel
Warning indicator illuminated. 'CHECK TYRE PRESSURE' message displayed
and applicable tire highlighted on display. Low pressure warning limit reached in one or
more wheels in low speed mode (only if programmed or learning) Warning indicator illuminated. 'CHECK ALL TYRE PRESSURES' message
displayed. TPMS fault
Warning indicator flashes for 72 seconds and is then permanently
illuminated. The flash sequence repeats after ignition on cycle. 'TYRE
PRESSURE SYSTEM FAULT' message displayed. No transmission from a specific tire pressure
sensor or Specific tire pressure sensor fault Warning indicator flashes for 72 seconds and is then permanently
illuminated. The flash sequence repeats after ignition on cycle. 'TYRE NOT
MONITORED' message displayed. No transmission from more than one tire pressure
sensor or more than one tire pressure sensor
fault Warning indicator flashes for 72 seconds and is then permanently
illuminated. The flash sequence repeats after ignition on cycle. 'TYRE
PRESSURE SYSTEM FAULT' message displayed. CAN (controller area network) signals missing
Warning indicator flashes for 72 seconds and is then permanently
illuminated. The flash sequence repeats after ignition on cycle. 'TYRE
PRESSURE SYSTEM FAULT' message displayed. Vehicle enters high speed mode (only available in
certain markets) Warning indicator illuminated. 'TYRE PRESSURE LOW FOR SPEED' message displayed.