2010 JAGUAR XFR Timing

6. NOTE: Tsubaki timing drive only.
Install the lower timing chain making sure the coloured
chain links align correctly with the fuel rail high-pressure
fuel pumps camshaft and crankshaft sprocket markings.

7. CAUTION: Make sure that the tensioner spring is
correctly located.


NOTE: Tsubaki timing drive only.
Torque: 21 Nm









8. NOTE: INA timing drive only.
Install the lower timing chain making sure the coloured
chain links align correctly with the fuel rail high-pressure
fuel pumps camshaft and crankshaft sprocket markings.

9. CAUTION: Make sure that the tensioner spring is
correctly located.


NOTE: INA timing drive only.
Torque: 21 Nm













10. Refer to: Oil Pan Extension (303-01C Engine - V8 5.0L Petrol, Removal and Installation).

11. Refer to: Battery Disconnect and Connect (414-01 Battery, Mounting and Cables, General Procedures).

Engine - V8 S/C 5.0L Petrol - Timing Cover
Removal and Installation

Removal


NOTE: Removal steps in this procedure may contain installation details. Published: 12-Sep-2011

1. Refer to: Battery Disconnect and Connect (414-01 Battery, Mounting and Cables, General Procedures).


2. WARNING: Make sure to support the vehicle with axle stands.
Raise and support the vehicle.

3. Refer to: Accessory Drive Belt (303-05D Accessory Drive - V8 S/C 5.0L Petrol, Removal and Installation).

4. Refer to: Accessory Drive Belt Tensioner (303-05D Accessory Drive - V8 S/C 5.0L Petrol, Removal and Installation).

5. Refer to: Thermostat Housing - Vehicles With: Supercharger (303-03C Engine Cooling - V8 5.0L Petrol/V8 S/C 5.0L Petrol, Removal and
Installation).

6. Refer to: Valve Cover LH (303-01D Engine - V8 S/C 5.0L Petrol, Removal and Installation).

7. Refer to: Valve Cover RH (303-01D Engine - V8 S/C 5.0L Petrol, Removal and Installation).

8. Refer to: Crankshaft Pulley (303-01D Engine - V8 S/C 5.0L Petrol, Removal and Installation).


9. NOTE: Engine shown removed for clarity.

Engine - V8 S/C 5.0L Petrol - Timing Drive Components
Removal and Installation

Special Tool(s)


303-1445
Timing Tool – Camshaft Alignment

303-1447
Timing Tool

303-1448
Locking Tool

303-1452
Camshaft Rotating Tool

303-1482
Tensioner Tool Removal


CAUTION: Check all timing components for wear and install new components if required.
NOTES:


Removal steps in this procedure may contain installation details. Published: 12-Jun-2014

Some variation in the illustrations may occur, but the essential information is always correct.

1. Disconnect the battery ground cable.

Refer to: Battery Disconnect and Connect (414-01 Battery, Mounting and Cables, General Procedures).


2. WARNING: Make sure to support the vehicle with axle stands.
Raise and support the vehicle.

3. Refer to: Timing Cover (303-01C Engine - V8 5.0L Petrol, Removal and Installation).

4.
5. CAUTION: Only rotate the crankshaft clockwise.
Install the special tool.

Special Tool(s): 303-1447

10.


































11. CAUTION: If the variable valve timing (VVT) units are
knocked or dropped then the VVT must be replaced.
Remove the timing chain with the VVT units. www.JagDocs.com

14.


































15. CAUTION: If the VVT is knocked or dropped then the
VVT must be replaced.
Remove the timing chain with the VVT units.