2010 JAGUAR XFR torque

Raise and support the vehicle.


10.





































11. CAUTION: Lubricate only the union threads with clean engine oil.

NOTE: Engine shown removed for clarity.
Torque: Unions (1) 21 Nm M6 (2) 11 Nm M8 (3) 25 Nm M5 nut (4) 6 Nm


























NOTE: Engine shown removed for clarity.
Torque: 21 Nm www.JagDocs.com

12.
13.
14. NOTES:

Install the bolt and unions finger tight before final tightening.

Remove and discard the blanking caps.
Torque: Unions 21 Nm M6 11 Nm














Torque: 21 Nm


















NOTE: Engine shown removed for clarity.
Torque: M10 29 Nm M6 11 Nm

15.

















16. NOTE: Engine shown removed for clarity.
















Torque: 25 Nm
















Left-hand drive vehicles

17. Torque: 100 Nm

18. Torque: 35 Nm










All vehicles

19. Refer to: Generator - V8 5.0L Petrol (414-02C Generator and Regulator - V8 5.0L Petrol/V8 S/C 5.0L Petrol, Removal and Installation).

20. Refer to: Engine Mount RH (303-01D Engine - V8 S/C 5.0L Petrol, Removal and Installation).

21. Lower the vehicle.

22.


















23.


















NOTES:

Lubricate
the
union
threads
with
clean
engine
oil.

Do
not tighten
at this
stage.

Remove
and
discard
the
blanking
caps.

Installation
10.
















11.

























12.


















Torque: 10 Nm
























CAUTIONS:


Take extra care when removing the throttle body,
failure to follow this instruction may result in damage to
the manifold absolute pressure and temperature (MAPT)
sensor.


Do not attempt to clean the throttle body bore, build
up of deposits reduces air leakage past the throttle plate at
the fully closed position.
Remove and discard the gasket.

1. To install, reverse the removal procedure.

Accessory Drive - V8 S/C 5.0L Petrol - Accessory Drive Belt
Removal and Installation

Removal


NOTE: Removal steps in this procedure may contain installation details. Published: 11-May-2011

1. Refer to: Battery Disconnect and Connect (414-01 Battery, Mounting and Cables, General Procedures).

2. Refer to: Supercharger Belt (303-05, Removal and Installation).


3. WARNING: Make sure to support the vehicle with axle stands.

Raise and support the vehicle.

4. Refer to: Air Deflector (501-02 Front End Body Panels, Removal and Installation).

5. Torque: 55 Nm 6. Torque: 25 Nm

Published: 11-May-2011
Accessory Drive - V8 S/C 5.0L Petrol - Accessory Drive Belt Idler Pulley
Removal and Installation

Removal


NOTE: Removal steps in this procedure may contain installation details.

1. Refer to: Battery Disconnect and Connect (414-01 Battery, Mounting and Cables, General Procedures).

2. Refer to: Supercharger Belt (303-05, Removal and Installation).

3. Refer to: Air Cleaner Outlet Pipe LH (303-12D Intake Air Distribution and Filtering - V8 S/C 5.0L Petrol, Removal and Installation).


4. NOTE: Note the fitted position.
















5. Torque: 25 Nm

Installation 6. Torque: 40 Nm
1. CAUTIONS:


Make sure the accessory belt is correctly aligned to the pulleys.
Failure to follow this instruction may result in damage to the vehicle.


Clean and inspect the accessory drive belt pulleys for damage.

To install, reverse the removal procedure. www.JagDocs.com