2010 JAGUAR XFR 414-01

(100-00 General Information, Description and Operation) /
Body Repairs (501-25A Body Repairs - General Information, Description and Operation) /
Corrosion Protection (501-25B Body Repairs - Corrosion Protection, Description and Operation) /
Body and Frame (501-26 Body Repairs - Vehicle Specific Information and Tolerance Checks, Description and Operation).

3. Disconnect the battery ground cable.
For additional information, refer to: Battery Disconnect and Connect (414-01 Battery, Mounting and Cables, General Procedures).

4. Remove the loadspace trim panel RH.
For additional information, refer to: Loadspace Trim Panel RH (501-05 Interior Trim and Ornamentation, Removal and Installation).

5. Disconnect the luggage compartment lid wiring harness.














6. NOTE: This step requires the aid of another technician.
Remove the luggage compartment lid.

(100-00 General Information, Description and Operation) /
Body Repairs (501-25A Body Repairs - General Information, Description and Operation) /
Corrosion Protection (501-25B Body Repairs - Corrosion Protection, Description and Operation) /
Body and Frame (501-26 Body Repairs - Vehicle Specific Information and Tolerance Checks, Description and Operation).


3. NOTE: If the procedure includes removal of the rear door components,
the battery can remain connected to aid their removal and disconnected
afterwards.
Disconnect the battery ground cable.
For additional information, refer to: Battery Disconnect and Connect (414-01 Battery, Mounting and Cables, General Procedures).


4. NOTE: For new rear door installation, this step may be carried out
later in the removal procedure.

Disconnect the rear door wiring harness, accessed behind the grommet
on the B-pillar.


5. NOTE: For new rear door installation, this step may be carried out
later in the removal procedure.
Release the rear door check strap from the body.


6. NOTE: This step is for removing the fully trimmed rear door for access
only, for installing a new front door, continue to removal step 7.

Published: 11-May-2011
Interior Trim and Ornamentation - Instrument Panel Speaker Grille
Removal and Installation

Removal


NOTE: Removal steps in this procedure may contain installation details.

1. Refer to: Battery Disconnect and Connect (414-01 Battery, Mounting and Cables, General Procedures).

2. CAUTIONS:


Protect the surrounding trim to avoid damage.
Make sure that the clips are correctly located.









3.
4. CAUTION: Make sure that the component is correctly
located on the locating dowels.


NOTE: Do not disassemble further if the component is
removed for access only.
Torque: 2 Nm

Interior Trim and Ornamentation - Headliner
Removal and Installation

Removal


NOTE: Removal steps in this procedure may contain installation details. Published: 11-May-2011

1. Refer to: Battery Disconnect and Connect (414-01 Battery, Mounting and Cables, General Procedures).

2. Refer to: Interior Rear View Mirror (501-09 Rear View Mirrors, Removal and Installation).

3. Refer to: Overhead Console (501-12 Instrument Panel and Console, Removal and Installation).

4.
Remove both sun visors.

Refer to: Sun Visor (501-05 Interior Trim and Ornamentation, Removal and Installation).

5.
Remove both A-pillar trim panels.

Refer to: A-Pillar Trim Panel (501-05 Interior Trim and Ornamentation, Removal and Installation).

6.
Remove both B-pillar upper trim panels.

Refer to: B-Pillar Upper Trim Panel (501-05 Interior Trim and Ornamentation, Removal and Installation).

7.
Remove both C-pillar trim panels.

Refer to: C-Pillar Trim Panel (501-05 Interior Trim and Ornamentation, Removal and Installation).

8.
Remove both front seats.

Refer to: Front Seat (501-10 Seating, Removal and Installation).
9. Refer to: Rear Seat Cushion (501-10 Seating, Removal and Installation).

4. NOTE: Right-hand shown, left-hand similar. Release the
safety belt lower anchor from the front seat.





















5. NOTES:


Left-hand shown, right-hand similar.


Some variation in the illustrations may occur, but the
essential information is always correct.
Remove the 2 rear bolts from the front seat.







6. Position the front seat fully rearwards.


7. NOTE: Left-hand shown, right-hand similar.
Remove the 2 front bolts from the front seat.










8. Reposition the front seat to the central position.

9. Disconnect the battery ground cable.
For additional information, refer to: Battery Disconnect and Connect (414-01 Battery, Mounting and Cables, General Procedures).

Seating - Front Seat Backrest
Removal and Installation Published: 11-May-2011

Removal

1. Make the air bag supplemental restraint system (SRS) safe.
For additional information, refer to: Standard Workshop Practices (100-00 General Information, Description and Operation).

2. Disconnect the battery ground cable.
For additional information, refer to: Battery Disconnect and Connect (414-01 Battery, Mounting and Cables, General Procedures).

3. Remove the front seat.
For additional information, refer to: Front Seat (501-10 Seating, Removal and Installation).


4. WARNING: This step requires the aid of another
technician.


CAUTION: Take extra care when handling the
component.
Remove the front seat backrest assembly.






















5. Remove the front seat backrest cover.
For additional information, refer to: Front Seat Backrest Cover (501-10 Seating, Removal and Installation).

6. Remove the backrest halo panel.
Release the 5 wiring harness clips.


7. NOTE: Do not disassemble further if the component is removed for
access only.
Remove the front seat recliner motor.
For additional information, refer to: Front Seat Recliner Motor (501-10,

Seating - Front Seat Bolster
Removal and Installation

Removal

NOTES:


Removal steps in this procedure may contain installation details.


Some variation in the illustrations may occur, but the essential information is always correct. Published: 11-May-2011

1. Refer to: Battery Disconnect and Connect (414-01 Battery, Mounting and Cables, General Procedures).

2. Refer to: Front Seat Backrest Cover (501-10 Seating, Removal and Installation).






Installation

3.

























4. WARNING: The procedure must be carried out on both
sides of the seat.


CAUTION: Make sure that the clips are correctly
located.

1. To install, reverse the removal procedure.

Seating - Front Seat Bolster Pump
Removal and Installation

Removal

NOTES:


Removal steps in this procedure may contain installation details.


Some variation in the illustrations may occur, but the essential information is always correct. Published: 11-May-2011

1. Refer to: Battery Disconnect and Connect (414-01 Battery, Mounting and Cables, General Procedures).

2. Refer to: Front Seat Backrest Cover (501-10 Seating, Removal and Installation).
3.
Installation

1. To install, reverse the removal procedure.