2010 JAGUAR XFR Relay

DTC Description Possible Causes Action B1B92-15
Seat Recline Motor Relay -
Circuit short to battery or
open
Driver seat recline motor
circuit - short to power, open
circuit
Carry out any pinpoint tests associated
with this DTC using the manufacturer
approved diagnostic system. Refer to the
electrical circuit diagrams and check driver
seat recline motor circuit for short to
power, open circuit B1B93-31
Seat Recline Motor
Speed/Position Sensor - No
signal
Harness/connector problem
No signal from sensor
Sensor/motor malfunction
Check the seat wiring harness/connectors
for security/integrity
Refer to the electrical circuit diagrams and
check the seat recline motor speed sensor
circuit. Repair circuit as required. Clear DTC
and retest B1B94-24
Seat Height Up Switch -
Signal stuck high
Signal stuck high
Check for a stuck switch. Refer to the
electrical circuit diagrams and check driver
seat switch pack to seat module LIN circuit
for short, open circuit and seat height up
circuit for short to ground B1B95-24
Seat Height Down Switch -
Signal stuck high
Signal stuck high
Check for a stuck switch. Refer to the
electrical circuit diagrams and check driver
seat switch pack to seat module LIN circuit
for short, open circuit and seat height
down circuit for short to ground B1B96-24
Seat Slide Forward Switch -
Signal stuck high
Signal stuck high
Check for a stuck switch. Refer to the
electrical circuit diagrams and check driver
seat switch pack to seat module LIN circuit
for short, open circuit and seat slide
forward circuit for short to ground B1B97-24 Seat Slide Backward Switch
- Signal stuck high
Signal stuck high
Check for a stuck switch. Refer to the
electrical circuit diagrams and check driver
seat switch pack to seat module LIN circuit
for short, open circuit and seat slide
backward circuit for short to ground B1B98-24
Seat Tilt Up Switch - Signal
stuck high
Signal stuck high
Check for a stuck switch. Refer to the
electrical circuit diagrams and check driver
seat switch pack to seat module LIN circuit
for short, open circuit and seat tilt up
circuit for short to ground B1B99-24
Seat Tilt Down Switch -
Signal stuck high
Signal stuck high
Check for a stuck switch. Refer to the
electrical circuit diagrams and check driver
seat switch pack to seat module LIN circuit
for short, open circuit and seat tilt down
circuit for short to ground B1C00-24
Seat Recline Up Switch -
Signal stuck high
Signal stuck high
Check for a stuck switch. Refer to the
electrical circuit diagrams and check driver
seat switch pack to seat module LIN circuit
for short, open circuit and seat recline up
circuit for short to ground B1C01-24
Seat Recline Down Switch -
Signal stuck high
Signal stuck high
Check for a stuck switch. Refer to the
electrical circuit diagrams and check driver
seat switch pack to seat module LIN circuit
for short, open circuit and check seat
recline down circuit for short to ground B1C02-24
Memory Store Switch -
Signal stuck high
Signal stuck high
Check for a stuck switch. Refer to the
electrical circuit diagrams and check driver
seat switch pack to seat module LIN circuit
for short, open circuit www.JagDocs.com

DTC Description Possible Causes Action P0031-13
HO2S Heater Control Circuit
Low (Bank 1, Sensor 1) -
Circuit open NOTES:


- Circuit HTR_CTRL_A_UPSTREAM -


LR - Circuit UHEGO HEATER A -

Pre catalyst oxygen sensor-odd
heater control circuit (Bank 1,
Sensor 1) circuit, open circuit
Using the manufacturer approved
diagnostic system check datalogger
signal, Oxygen Sensor (O2S) Heater
Duty Cycle Bank 1 Sensor 1 (0x03A1)
Refer to the electrical circuit
diagrams and check pre catalyst
oxygen sensor-odd heater control
circuit (Bank 1, Sensor 1) circuit for
open circuit P0032-12
HO2S Heater Control Circuit
High (Bank 1, Sensor 1) -
Circuit short to battery NOTES:


- Circuit HTR_CTRL_A_UPSTREAM -


LR - Circuit UHEGO HEATER A -

Pre catalyst oxygen sensor-odd
heater control circuit (Bank 1,
Sensor 1) circuit short circuit to
power
Using the manufacturer approved
diagnostic system check datalogger
signal, Oxygen Sensor (O2S) Heater
Duty Cycle Bank 1 Sensor 1 (0x03A1)
Refer to the electrical circuit
diagrams and check pre catalyst
oxygen sensor-odd heater control
circuit (Bank 1, Sensor 1) circuit for
short circuit to power P0036-00
HO2S Heater Control Circuit
(Bank 1, Sensor 2) - No sub
type information
NOTE: - Circuit HTR_HEGO_A -

Catalyst oxygen sensor heater
circuit control fuse failure
Post catalyst oxygen sensor-odd
heater control circuit short circuit
to ground, short circuit to power,
open circuit
Catalyst oxygen sensor heater
circuit control relay circuit short
circuit to ground, short circuit to
power, open circuit
Catalyst oxygen sensor heater
circuit control relay failure
Post catalyst oxygen sensor-odd
failure
Using the manufacturer approved
diagnostic system check datalogger
signal, Oxygen Sensor (O2S) Heater
Duty Cycle Bank 1 Sensor 2 (0x03A2)
Refer to the electrical circuit
diagrams and check post catalyst
oxygen sensor-odd sensor fuse for
open circuit
Refer to the electrical circuit
diagrams and check post catalyst
oxygen sensor-odd sensor circuit for
short circuit to ground, short circuit
to power, open circuit
Refer to the electrical circuit
diagrams and check catalyst oxygen
sensor heater circuit control relay
circuit for short circuit to ground,
short circuit to power, open circuit
Check and install a new catalyst
oxygen sensor heater control relay,
as required. Check and install a new
post catalyst oxygen sensor-odd as
required. Refer to the warranty policy
and procedures manual, or determine
if any prior approval programme is in
operation, prior to the installation of
a new module/component P0051-11
HO2S Heater Control Circuit
Low (Bank 2, Sensor 1) -
Circuit short to ground NOTES:


- Circuit HTR_CTRL_B_UPSTREAM -


LR - Circuit UHEGO HEATER B -

Pre catalyst oxygen sensor-even
heater control circuit (Bank 2,
Sensor 1) circuit short circuit to
ground
Using the manufacturer approved
diagnostic system check datalogger
signal, Oxygen Sensor (O2S) Heater
Duty Cycle Bank 2 Sensor 1 (0x03A4)
Refer to the electrical circuit
diagrams and check pre catalyst
oxygen sensor-even heater control
circuit (Bank 2, Sensor 1) circuit for
short circuit to ground P0051-13
HO2S Heater Control Circuit
Low (Bank 2, Sensor 1) -
Circuit open NOTES:


- Circuit HTR_CTRL_B_UPSTREAM -


LR - Circuit UHEGO HEATER B -
Using the manufacturer approved
diagnostic system check datalogger
signal, Oxygen Sensor (O2S) Heater
Duty Cycle Bank 2 Sensor 1 (0x03A4)
Refer to the electrical circuit
diagrams and check pre catalyst
oxygen sensor-even heater control
circuit (Bank 2, Sensor 1) circuit for

DTC Description Possible Causes Action
Pre catalyst oxygen sensor-even
heater control circuit (Bank 2,
Sensor 1) circuit, open circuit open circuit P0052-12
HO2S Heater Control Circuit
High (Bank 2, Sensor 1) -
Circuit short to battery NOTES:


- Circuit HTR_CTRL_B_UPSTREAM -


LR - Circuit UHEGO HEATER B -

Pre catalyst oxygen sensor-even
heater control circuit (Bank 2,
Sensor 1) circuit short circuit to
power
Using the manufacturer approved
diagnostic system check datalogger
signal, Oxygen Sensor (O2S) Heater
Duty Cycle Bank 2 Sensor 1 (0x03A4)
Refer to the electrical circuit
diagrams and check pre catalyst
oxygen sensor-even heater control
circuit (Bank 2, Sensor 1) circuit for
short circuit to power P0054-00
HO2S Heater Resistance
(Bank 1, Sensor 2) - No sub
type information NOTES:


- Circuit HTR_CTRL_A_UPSTREAM -


LR - Circuit UHEGO HEATER A -

Catalyst oxygen sensor heater
circuit control fuse failure
Post catalyst oxygen sensor-odd
heater control circuit short circuit
to ground, short circuit to power,
open circuit, high resistance
Catalyst oxygen sensor heater
circuit control relay circuit short
circuit to ground, short circuit to
power, open circuit
Catalyst oxygen sensor heater
circuit control relay failure
Post catalyst oxygen sensor-odd
failure
Using the manufacturer approved
diagnostic system check datalogger
signal, Oxygen Sensor (O2S) Heater
Duty Cycle Bank 1 Sensor 1 (0x03A1)
Refer to the electrical circuit
diagrams and check post catalyst
oxygen sensor-odd sensor fuse for
open circuit
Refer to the electrical circuit
diagrams and check post catalyst
oxygen sensor-odd sensor circuit for
short circuit to ground, short circuit
to power, open circuit, high
resistance
Refer to the electrical circuit
diagrams and check catalyst oxygen
sensor heater circuit control relay
circuit for short circuit to ground,
short circuit to power, open circuit
Check and install a new catalyst
oxygen sensor heater control relay,
as required. Check and install a new
post catalyst oxygen sensor-odd as
required. Refer to the warranty policy
and procedures manual, or determine
if any prior approval programme is in
operation, prior to the installation of
a new module/component P0056-00
HO2S Heater Control Circuit
(Bank 2, Sensor 2) - No sub
type information
NOTE: - Circuit HTR_HEGO_B -

Post catalyst oxygen sensor-even
heater control circuit short circuit
to ground, short circuit to power,
open circuit
Catalyst oxygen sensor heater
circuit control relay circuit short
circuit to ground, short circuit to
power, open circuit
Catalyst oxygen sensor heater
circuit control relay failure
Post catalyst oxygen sensor-even
failure
Using the manufacturer approved
diagnostic system check datalogger
signal, Oxygen Sensor (O2S) Heater
Duty Cycle Bank 2 Sensor 2 (0x03A5)
Refer to the electrical circuit
diagrams and check post catalyst
oxygen sensor-even sensor circuit for
short circuit to ground, short circuit
to power, open circuit
Refer to the electrical circuit
diagrams and check catalyst oxygen
sensor heater circuit control relay
circuit for short circuit to ground,
short circuit to power, open circuit
Check and install a new catalyst
oxygen sensor heater control relay,
as required. Check and install a new
post catalyst oxygen sensor-even, as
required. Refer to the warranty policy
and procedures manual, or determine
if any prior approval programme is in
operation, prior to the installation of
a new module/component P0060-00
HO2S Heater Resistance
(Bank 2, Sensor 2) - No sub
type information NOTES:


- Circuit HTR_CTRL_B_UPSTREAM -
Using the manufacturer approved
diagnostic system check datalogger
signal, Oxygen Sensor (O2S) Heater
Duty Cycle Bank 2 Sensor 2 (0x03A5)

DTC Description Possible Causes Action
LR - Circuit UHEGO HEATER B -

Catalyst oxygen sensor heater
circuit control fuse failure
Post catalyst oxygen sensor-even
heater control circuit short circuit
to ground, short circuit to power,
open circuit, high resistance
Catalyst oxygen sensor heater
circuit control relay circuit short
circuit to ground, short circuit to
power, open circuit
Catalyst oxygen sensor heater
circuit control relay failure
Post catalyst oxygen sensor-even
failure Refer to the electrical circuit
diagrams and check post catalyst
oxygen sensor-even sensor fuse for
open circuit
Refer to the electrical circuit
diagrams and check post catalyst
oxygen sensor-even sensor circuit for
short circuit to ground, short circuit
to power, open circuit, high
resistance
Refer to the electrical circuit
diagrams and check catalyst oxygen
sensor heater circuit control relay
circuit for short circuit to ground,
short circuit to power, open circuit
Check and install a new catalyst
oxygen sensor heater control relay,
as required. Check and install a new
post catalyst oxygen sensor-even as
required. Refer to the warranty policy
and procedures manual, or determine
if any prior approval programme is in
operation, prior to the installation of
a new module/component P0069-29
MAP - Barometric Pressure
Correlation - Signal invalid
Manifold absolute pressure sensor
failure
Engine control module failure
Using the manufacturer approved
diagnostic system check datalogger
signal, Barometric Pressure Sensor
Voltage (0x035A). Check for related
manifold absolute pressure sensor
DTCs
Refer to the electrical circuit
diagrams and check manifold
absolute pressure sensor circuit for
short circuit to ground, short circuit
to power, open circuit
Check and install new manifold
absolute pressure sensor as
required. Check and install a new
engine control module as required.
Refer to the warranty policy and
procedures manual, or determine if
any prior approval programme is in
operation, prior to the installation of
a new module/component P0071-21
Ambient Air Temperature
Sensor Range/Performance -
Signal amplitude < minimum NOTES:


Jaguar - Circuit
AMBIENT_TEMP_SENSOR -


LR - Circuit TAMB TEMP -

Ambient air temperature sensor
circuit short circuit to ground, short
circuit to power, open circuit
Temperature and manifold absolute
pressure sensor circuit short circuit
to ground, short circuit to power,
open circuit
Ambient air temperature sensor
failure
Temperature and manifold absolute
pressure sensor failure
Using the manufacturer approved
diagnostic system check datalogger
signal, Ambient Air Temperature
Sensor Voltage (0x03BA)
Refer to the electrical circuit
diagrams and check ambient air
temperature sensor circuit for short
circuit to ground, short circuit to
power, open circuit
Refer to the electrical circuit
diagrams and check temperature and
manifold absolute pressure sensor
circuit for short circuit to ground,
short circuit to power, open circuit
Check and install a new ambient air
temperature sensor as required.
Check and install a new temperature
and manifold absolute pressure
sensor as required. Refer to the
warranty policy and procedures
manual, or determine if any prior
approval programme is in operation,
prior to the installation of a new
module/component P0071-22
Ambient Air Temperature
Sensor Range/Performance -
Signal amplitude > maximum NOTES:


- Circuit AMBIENT_TEMP_SENSOR -
Using the manufacturer approved
diagnostic system check datalogger
signal, Ambient Air Temperature
Sensor Voltage (0x03BA)
Refer to the electrical circuit www.JagDocs.com

DTC Description Possible Causes Action P007B-24
Charge Air Cooler
Temperature Sensor Circuit
Range/Performance (Bank 1)
- Signal stuck high
NOTE: Jaguar circuit reference
IC_COOLANT_PMP_CTRL &
BOOST_PRESS_SENSOR_TEMP_SIG. Land
Rover circuit reference O_S_CACWPR &
I_A_BTS

Connector is disconnected,
connector pin is backed out,
connector pin corrosion
Fuse failure
Temperature and manifold absolute
pressure sensor circuit, short
circuit to ground, short circuit to
power, open circuit, high resistance
Temperature and manifold absolute
pressure sensor failure
Air charge coolant pump and
control circuit, short circuit to
ground, short circuit to power, open
circuit, high resistance
Air charge coolant pump relay
failure
Air charge coolant pump failure
Inspect connectors for signs of water
ingress, and pins for damage and/or
corrosion
Refer to electrical circuit diagrams
and check for fuse failure, install
new fuse as required
Refer to electrical circuit diagrams
and check the temperature and
manifold absolute pressure sensor
circuit for short circuit to ground,
short circuit to power, open circuit,
high resistance
Check and install a new temperature
and manifold absolute pressure
sensor as required
Refer to electrical circuit diagrams
and check the air charge coolant
pump and control circuit for short
circuit to ground, short circuit to
power, open circuit, high resistance
Refer to electrical circuit diagrams
and check the air charge coolant
pump for open circuit, high
resistance
Refer to the relevant section of the
workshop manual and check the air
charge coolant pump for correct
operation. Check and install a new
air charge coolant pump as required
Clear DTC and retest P007B-29
Charge Air Cooler
Temperature Sensor Circuit
Range/Performance (Bank 1)
- Signal invalid
NOTE: Jaguar circuit reference
IC_COOLANT_PMP_CTRL &
BOOST_PRESS_SENSOR_TEMP_SIG. Land
Rover circuit reference O_S_CACWPR &
I_A_BTS

Connector is disconnected,
connector pin is backed out,
connector pin corrosion
Fuse failure
Temperature and manifold absolute
pressure sensor circuit, short
circuit to ground, short circuit to
power, open circuit, high resistance
Temperature and manifold absolute
pressure sensor failure
Air charge coolant pump and
control circuit, short circuit to
ground, short circuit to power, open
circuit, high resistance
Air charge coolant pump relay
failure
Air charge coolant pump failure
Inspect connectors for signs of water
ingress, and pins for damage and/or
corrosion
Refer to electrical circuit diagrams
and check for fuse failure, install
new fuse as required
Refer to electrical circuit diagrams
and check the temperature and
manifold absolute pressure sensor
circuit for short circuit to ground,
short circuit to power, open circuit,
high resistance
Check and install a new temperature
and manifold absolute pressure
sensor as required
Refer to electrical circuit diagrams
and check the air charge coolant
pump and control circuit for short
circuit to ground, short circuit to
power, open circuit, high resistance
Refer to electrical circuit diagrams
and check the air charge coolant
pump for open circuit, high
resistance
Refer to the relevant section of the
workshop manual and check the air
charge coolant pump for correct
operation. Check and install a new
air charge coolant pump as required
Clear DTC and retest P007C-00
Charge Air Cooler
Temperature Sensor Circuit
Low (Bank 1) - No sub type
information
NOTE: - Circuit TMAP_TEMP_SENSOR
-

Charge air cooler temperature
sensor (Bank 1) circuit short circuit
to ground, open circuit, high
resistance
Charge air cooler temperature
sensor (Bank 1) failure
Refer to the electrical circuit
diagrams and check charge air cooler
temperature sensor (Bank 1) circuit
for short circuit to ground, open
circuit, high resistance
Check and install a new charge air
cooler temperature sensor (Bank 1)
as required. Refer to the warranty
policy and procedures manual, or
determine if any prior approval
programme is in operation, prior to
the installation of a new
module/component

DTC Description Possible Causes Action B100A-51 Fuel Pump Authorisation
- Not programmed
RJB fault
Low speed CAN fault
Instrument cluster fault
Check power and ground supplies to RJB. Check CAN
communications between RJB and instrument
cluster. Check power and ground supplies to
instrument cluster B100A-62 Fuel Pump Authorisation
- Signal compare failure
Low speed CAN fault
RJB fault
Instrument cluster fault
Incorrect module
installed
(RJB/Instrument cluster)
Write target SID
synchronisation error
following
re-programming
Noise/EMC related error
Check CAN communications between RJB and
instrument cluster. Check power and ground supplies
to RJB and instrument cluster. Confirm correct
module installed. Re-synchronise ID by
re-configuring the RJB as a new module. Check CAN
network for interference/EMC related issues B100A-63 Fuel Pump Authorisation
- Circuit/component
protection time-out
RJB fault
Low speed CAN fault
Instrument cluster fault
Low battery voltage <9V
Check power and ground supplies to RJB and
instrument cluster. Check CAN communications
between RJB and instrument cluster. Check battery
is in fully charged and serviceable condition, refer to
the battery care manual B1026-12
Steering Column Lock -
Circuit short to battery
Steering column lock
ground circuit - short to
power
Refer to the electrical circuit diagrams and check
steering column lock ground circuit for short to
power B1087-83
LIN Bus "A" - Value of
signal protection
calculation incorrect
The checksum of the
received LIN frame is
incorrect
Check the battery monitoring system and rear
parking aid system for DTCs and refer to relevant
DTC Index B1087-86
LIN Bus "A" - Signal
invalid
The header of the LIN
message received is
incorrect
Carry out any pinpoint test associated with this DTC
using the manufacturer approved diagnostic system.
Check the battery monitoring system and rear
parking aid system for DTCs and refer to relevant
DTC Index B1087-88 LIN Bus "A" - Bus off
Battery monitoring
system LIN circuit -
short to ground, power
Carry out any pinpoint test associated with this DTC
using the manufacturer approved diagnostic system.
Refer to the electrical circuit diagrams and check
battery monitoring system LIN circuit for short to
ground, power B108A-23
Start Button - Signal
stuck low
Start/Stop switch digital
input signal circuit -
stuck low
Carry out any pinpoint test associated with this DTC
using the manufacturer approved diagnostic system.
Refer to the electrical circuit diagrams and check
Start/Stop switch digital input signal circuit for short
to ground B10A1-11 Trailer Tow Detection -
Circuit short to ground
Trailer tow detection
digital input circuit -
short to ground
Carry out any pinpoint test associated with this DTC
using the manufacturer approved diagnostic system.
Refer to the electrical circuit diagrams and check
trailer tow detection digital input circuit for short to
ground B10AF-12
Blower Fan Relay -
Circuit short to battery
High Side output not
driven - Diagnosis
feedback indicates
output is short to power
Refer to the electrical circuit diagrams and check
blower motor supply circuit for short to power B10AF-14
Blower Fan Relay -
Circuit short to ground
or open
High Side output not
driven - Diagnosis
feedback indicates
output is short to
ground, open circuit
Refer to the electrical circuit diagrams and check
blower motor supply circuit for short to ground, open
circuit

DTC Description Possible Causes Action B10AF-93
Blower Fan Relay - No
operation
High Side output not
driven - Diagnosis
feedback indicates
output is at open load
or short to power
Carry out any pinpoint test associated with this DTC
using the manufacturer approved diagnostic system.
Refer to the electrical circuit diagrams and check
blower motor supply circuit for short to power, open
circuit B10DD-11
Airbag Deployed -
Circuit short to ground
Airbag deployed digital
input signal circuit -
short to ground
Carry out any pinpoint test associated with this DTC
using the manufacturer approved diagnostic system.
Refer to the electrical circuit diagrams and check
airbag deployed digital input signal circuit for short
to ground B10DD-15
Airbag Deployed -
Circuit short to battery
or open
Airbag deployed digital
input signal circuit -
short to power, open
circuit
Carry out any pinpoint test associated with this DTC
using the manufacturer approved diagnostic system.
Refer to the electrical circuit diagrams and check
airbag deployed digital input signal circuit for short
to power, open circuit B10DD-38
Airbag Deployed - Signal
frequency incorrect
Signal frequency
incorrect
Check the RCM for related DTCs and refer to the
relevant DTC Index B10DE-11
Low Fuel Warning
Switch - Circuit short to
ground
Diesel run-dry switch
analogue input circuit -
short to ground
Carry out any pinpoint test associated with this DTC
using the manufacturer approved diagnostic system.
Refer to the electrical circuit diagrams and check
diesel run-dry switch analogue input circuit for short
to ground B10DE-15
Low Fuel Warning
Switch - Circuit short to
battery or open
Diesel run-dry switch
analogue input circuit -
short to power, open
circuit
Carry out any pinpoint test associated with this DTC
using the manufacturer approved diagnostic system.
Refer to the electrical circuit diagrams and check
diesel run-dry switch analogue input circuit for short
to power, open circuit B1112-11
Park Aid Ignition -
Circuit short to ground
Parking aid ignition
supply circuit - short to
ground
Carry out any pinpoint test associated with this DTC
using the manufacturer approved diagnostic system.
Refer to the electrical circuit diagrams and check
parking aid ignition supply circuit for short to ground B1112-12
Park Aid Ignition -
Circuit short to battery
Parking aid ignition
supply circuit - short to
power
Refer to the electrical circuit diagrams and check
parking aid ignition supply circuit for short to power B1115-11
High Mounted Stop
Lamp Control - Circuit
short to ground
High mounted stop lamp
control circuit - short to
ground
Carry out any pinpoint test associated with this DTC
using the manufacturer approved diagnostic system.
Refer to the electrical circuit diagrams and check
high mounted stop lamp control circuit for short to
ground B1116-11
Left Tail Lamp - Circuit
short to ground
Left hand tail lamp
control circuit - short to
ground
Carry out any pinpoint test associated with this DTC
using the manufacturer approved diagnostic system.
Refer to the electrical circuit diagrams and check left
hand tail lamp control circuit for short to ground B1117-11
Right Tail Lamp - Circuit
short to ground
Right hand tail lamp
control circuit - short to
ground
Carry out any pinpoint test associated with this DTC
using the manufacturer approved diagnostic system.
Refer to the electrical circuit diagrams and check
right hand tail lamp control circuit for short to
ground B111A-11
Number Plate Lamps -
Circuit short to ground
Right hand or left hand
number plate lamp
control circuits - short to
ground
Carry out any pinpoint test associated with this DTC
using the manufacturer approved diagnostic system.
Refer to the electrical circuit diagrams and check
right hand and left hand number plate lamp control
circuits for short to ground www.JagDocs.com

DTC Description Possible Causes Action B111A-12
Number Plate Lamps -
Circuit short to battery
Right hand or left hand
number plate lamp
control circuits - short to
power
Refer to the electrical circuit diagrams and check
right hand and left hand number plate lamp control
circuits for short to power B111A-13
Number Plate Lamps -
Circuit open
Right hand or left hand
number plate lamp
control circuits - open
circuit
Refer to the electrical circuit diagrams and check
right hand and left hand number plate lamp control
circuits for open circuit B111A-15
Number Plate Lamps -
Circuit short to battery
or open
Right or left side licence
plate lamp(s)
inoperative
Right or left side licence
plate lamp control
circuits - short circuit to
power, open circuit, high
resistance
Refer to the electrical circuit diagrams and check
right side and left side licence plate lamp control
circuits for short circuit to power, open circuit, high
resistance. Repair wiring harness as required. Clear
DTC and retest B111D-12
Boot/Trunk Motor Open -
Circuit short to battery
Luggage compartment
lid latch actuator control
circuit - short to power
Carry out any pinpoint test associated with this DTC
using the manufacturer approved diagnostic system.
Refer to the electrical circuit diagrams and check
luggage compartment lid latch actuator control
circuit for short to power B111D-14
Boot/Trunk Motor Open -
Circuit short to ground
or open
Luggage compartment
lid latch actuator control
circuit - short to ground,
open circuit
Carry out any pinpoint test associated with this DTC
using the manufacturer approved diagnostic system.
Refer to the electrical circuit diagrams and check
luggage compartment lid latch actuator control
circuit for short to ground, open circuit B111E-11
Boot/Trunk Lamps -
Circuit short to ground
Luggage compartment
lamp control circuit -
short to ground
Carry out any pinpoint test associated with this DTC
using the manufacturer approved diagnostic system.
Refer to the electrical circuit diagrams and check
luggage compartment lamp control circuit for short
to ground B111E-12
Boot/Trunk Lamps -
Circuit short to battery
Luggage compartment
lamp control circuit -
short to power
Refer to the electrical circuit diagrams and check
luggage compartment lamp control circuit for short
to power B111E-13
Boot/Trunk Lamps -
Circuit open
Luggage compartment
lamp control circuit -
open circuit
Refer to the electrical circuit diagrams and check
luggage compartment lamp control circuit for open
circuit B111E-15
Boot/Trunk Lamps -
Circuit short to battery
or open
Luggage compartment
lamp inoperative
Luggage compartment
lamp control circuit -
short circuit to power,
open circuit, high
resistance
Refer to the electrical circuit diagrams and check
luggage compartment lamp control circuit for short
circuit to power, open circuit, high resistance. Repair
wiring harness as required. Clear DTC and retest B1123-12
Restraints Ignition
Relay - Circuit short to
battery
High Side output not
driven - diagnosis
feedback indicates
output is short to power
Carry out any pinpoint test associated with this DTC
using the manufacturer approved diagnostic system.
Refer to the electrical circuit diagrams and check
restraints ignition relay output for short to power B1123-14
Restraints Ignition
Relay - Circuit short to
ground or open
High Side output not
driven - diagnosis
feedback indicates
output is short to
ground, open circuit
Carry out any pinpoint test associated with this DTC
using the manufacturer approved diagnostic system.
Refer to the electrical circuit diagrams and check
restraints ignition relay output for short to ground,
open circuit B1123-93
Restraints Ignition
Relay - No operation
High Side output not
driven - diagnosis
feedback indicates
output is at open load
Carry out any pinpoint test associated with this DTC
using the manufacturer approved diagnostic system.
Refer to the electrical circuit diagrams and check
restraints ignition relay output for open load or