2010 JAGUAR XFR Exhaust

6. CAUTION: Make sure that the exhaust system is
supported with suitable retaining straps.
Tighten the top retaining nut first.
Torque:
Top nut 40 Nm Bottom nut 40 Nm

















7. CAUTION: Make sure that the exhaust system is
supported with suitable retaining straps.

Torque: 55 Nm












8. CAUTIONS:


Make sure the anti-seize compound does not contact
the catalyst monitor sensor tip.


If accidentally dropped or knocked install a new
sensor.
NOTES:


Do not disassemble further if the component is
removed for access only.


If the original sensor is to be installed, apply lubricant
meeting specification ESE-M12A4-A to the thread of the
sensor.
Torque: 48 Nm
Installation

1. To install, reverse the removal procedure.

Published: 11-May-2011
Exhaust System - V8 5.0L Petrol/V8 S/C 5.0L Petrol - Catalytic Converter RH
Removal and Installation

Removal


NOTE: Removal steps in this procedure may contain installation details.

1. Refer to: Battery Disconnect and Connect (414-01 Battery, Mounting and Cables, General Procedures).

2. WARNINGS:


Make sure to support the vehicle with axle stands.


Observe due care when working near a hot exhaust system.
Raise and support the vehicle.

3. Refer to: Air Deflector (501-02 Front End Body Panels, Removal and Installation).

4. Refer to: Engine Rear Undershield (501-02 Front End Body Panels, Removal and Installation).


5. CAUTION: Make sure the catalyst monitor sensor wiring
harness is not twisted more than 180 degrees and is not in
contact with either the exhaust or driveshaft.

6. CAUTION: Make sure that the exhaust system is
supported with suitable retaining straps.
Tighten the top retaining nut first.
Torque:
Top nut 40 Nm Bottom nut 40 Nm

















7. CAUTION: Make sure that the exhaust system is
supported with suitable retaining straps.

Torque: 55 Nm












8. CAUTIONS:


Make sure the anti-seize compound does not contact
the catalyst monitor sensor tip.


If accidentally dropped or knocked install a new
sensor.
NOTES:


Do not disassemble further if the component is
removed for access only.


If the original sensor is to be installed, apply lubricant
meeting specification ESE-M12A4-A to the thread of the
sensor.
Torque: 48 Nm
Installation

1. To install, reverse the removal procedure.

Published: 11-May-2011
Exhaust System - V8 5.0L Petrol/V8 S/C 5.0L Petrol - Exhaust Sound
Enhancement Valve
Removal and Installation

Removal


WARNING: Observe due care when working near a hot exhaust system.

NOTES:


The exhaust sound enhancement valve is an integeral part of the muffler and cannot be serviced separately.


Removal steps in this procedure may contain installation details.


1. WARNING: Make sure to support the vehicle with axle stands.
Raise and support the vehicle.




Installation

2. CAUTION: Make sure that these components are
installed to the noted removal position.

Torque:
M8 25 Nm M10 55 Nm
1. To install, reverse the removal procedure.

Published: 11-May-2011
Exhaust System - V8 5.0L Petrol/V8 S/C 5.0L Petrol - Exhaust System
Removal and Installation

Removal


NOTE: Removal steps in this procedure may contain installation details.

1. Refer to: Battery Disconnect and Connect (414-01 Battery, Mounting and Cables, General Procedures).

2. WARNINGS:


Make sure to support the vehicle with axle stands.


Observe due care when working near a hot exhaust system.
Raise and support the vehicle.

3. Refer to: Air Deflector (501-02 Front End Body Panels, Removal and Installation).

4. Refer to: Engine Rear Undershield (501-02 Front End Body Panels, Removal and Installation).

5.
6. www.JagDocs.com

7. CAUTION: Make sure that the exhaust system is
supported with suitable retaining straps.
Torque: 40 Nm




















8. Torque: 40 Nm

9.























10.
11. CAUTION: Make sure that the exhaust system is
supported with suitable retaining straps.
























CAUTION: Make sure that the exhaust system is
supported with suitable retaining straps.
Torque: 30 Nm














CAUTION: Make sure that the exhaust system is
supported with suitable retaining straps.
Torque: 6 Nm

Published: 09-Dec-2012
Exhaust System - V8 5.0L Petrol/V8 S/C 5.0L Petrol - Front Muffler
Removal and Installation

Removal


NOTE: Removal steps in this procedure may contain installation details.

1. WARNINGS:


Make sure to support the vehicle with axle stands.


Observe due care when working near a hot exhaust system.
Raise and support the vehicle.

2. Refer to: Engine Rear Undershield (501-02 Front End Body Panels, Removal and Installation).

3. Torque: 55 Nm 4. Torque: 55 Nm