2010 JAGUAR XFR wheel

Tires, Removal and Installation).


3. NOTE: Use an additional wrench to prevent the ball joint
rotating.
Remove the front stabilizer bar link.
Remove and discard the 2 nuts.










Installation


1. NOTE: Use an additional wrench to prevent the ball joint
rotating.
Install the front stabilizer bar link.
Tighten the upper nut to 47 Nm.
Tighten the lower nut to 70 Nm.









2. Install the wheel and tire.
For additional information, refer to: Wheel and Tire (204-04 Wheels and Tires, Removal and Installation).

Front Suspension - Stabilizer Bar Link Bushing
Removal and Installation

Special Tool(s)


Bush installer
204-340

Bush remove
204-342

Support
204-341

Support
204-339 Removal Published: 11-May-2011

CAUTION: The final tightening of the suspension components must be carried out with the vehicle on its wheels.


1. WARNING: Do not work on or under a vehicle supported only by a jack.
Always support the vehicle on safety stands.
Raise the vehicle on a 4 post lift.

2. Remove the rear lower arm.
For additional information, refer to: Rear Lower Arm (204-01 Front Suspension, Removal and Installation).

Suspension, Removal and Installation).


5. CAUTION: The final tightening of the suspension components
must be carried out with the vehicle on its wheels.


NOTE: Some variation in the illustrations may occur, but
the essential information is always correct.
Tighten to 47 Nm.








6. CAUTION: The final tightening of the suspension
components must be carried out with the vehicle on its wheels.


NOTE: Some variation in the illustrations may occur, but
the essential information is always correct.
Tighten to 47 Nm.






7. Install the air cleaner.
For additional information, refer to: Air Cleaner (303-12A, Removal and
Installation) /
Air Cleaner (303-12B Intake Air Distribution and Filtering - V6 3.0L Petrol, Removal and Installation) /
Air Cleaner (303-12C, Removal and Installation) /
Air Cleaner LH (303-12D, Removal and Installation).

8. Install the secondary bulkhead panel LH.
For additional information, refer to: Secondary Bulkhead Panel LH - 3.0L NA V6 - AJ27 (501-02 Front End Body Panels, Removal and Installation).

5. CAUTION: The final tightening of the suspension components
must be carried out with the vehicle on its wheels.


NOTE: Some variation in the illustrations may occur, but
the essential information is always correct.
Tighten to 47 Nm.








6. CAUTION: The final tightening of the suspension
components must be carried out with the vehicle on its wheels.


NOTE: Some variation in the illustrations may occur, but
the essential information is always correct.
Tighten to 47 Nm.






7. Install the secondary bulkhead panel RH.
For additional information, refer to: Secondary Bulkhead Panel RH - 3.0L NA V6 - AJ27 (501-02 Front End Body Panels, Removal and Installation).

Published: 11-May-2011
Front Suspension - Front Wheel Bearing and Wheel Hub TDV6 3.0L Diesel /V8 5.0L Petrol/V8 S/C 5.0L Petrol
Removal and Installation

Removal


NOTE: Removal steps in this procedure may contain installation details.


1. WARNING: Make sure to support the vehicle with axle stands.

Raise and support the vehicle.

2. Torque: 125 Nm 3. Torque: 10 Nm

7. CAUTIONS:


Discard the bolts.


Make sure that the area around the component is
clean and free of foreign material.


Do not attempt to release the wheel hub by hitting it
with a hammer directly, loosen the wheel hub retaining
bolts partially before applying an even amount of force to
the head of each bolts to release the wheel hub from the
wheel knuckle. Failure to follow this instruction may cause
damage to the component.
NOTES:


Some variation in the illustrations may occur, but the
essential information is always correct.


LH illustration shown, RH is similar.


Install the components to their original fitted
positions.
Torque: 90 Nm
Installation

1. To install, reverse the removal procedure. www.JagDocs.com

Front Suspension - Wheel Knuckle
Removal and Installation Published: 11-May-2011



Removal

1. WARNING: Do not work on or under a vehicle supported only by a
jack. Always support the vehicle on safety stands.

Raise and support the vehicle.

2. Remove the hub assembly.
For additional information, refer to: Front Wheel Bearing and Wheel Hub - V6 3.0L Petrol (204-01 Front Suspension, Removal and Installation).

3. NOTE: LH illustration shown, RH is similar.

Remove the brake disc shield.
Remove the 3 rivets.













4. NOTES:


LH illustration shown, RH is similar.


Use an additional wrench to prevent the ball joint
rotating.
Disconnect the steering gear tie rod end ball joint.
Remove and discard the tie rod end retaining nut. Ball joint splitter
204-327 Special Tool(s)

5. NOTES:


Use an additional wrench to prevent the ball joint
rotating.


LH illustration shown, RH is similar.
Disconnect the upper arm from the wheel knuckle.
Remove and discard the nut.








6. CAUTION: Make sure the ball joint seal is not
damaged. A damaged seal will lead to the premature failure
of the joint.

NOTES:


Use an additional wrench to prevent the ball joint
rotating.


LH illustration shown, RH is similar.

Remove the wheel knuckle.
Remove and discard the nut.
Using the special tool, release the ball joint from
the lower suspension arm.

Installation


1. NOTE: Use an additional wrench to prevent the ball joint
rotating.
Install the wheel knuckle.
Clean the component mating faces.
Tighten the nut to 92 Nm.