2010 JAGUAR XFR wheel

2. CAUTION: Nuts and bolts must be tightened with the
weight of the vehicle on the suspension.
Secure the lower arm to the wheel hub assembly.












3. CAUTION: Do not allow the brake caliper to hang on the
brake hose.


NOTE: Make sure that new bolts are installed.

Secure the rear brake caliper.
Tighten the bolts to 103 Nm.








4. Secure the rear stabilizer bar link.
Tighten the nut to 48 Nm.















5. CAUTION: Nuts and bolts must be tightened with the
weight of the vehicle on the suspension.

Secure the shock absorber and spring assembly to the lower
arm.









6. Install the wheel and tire.
For additional information, refer to: W heel and Tire (204-04 Wheels and Tires, Removal and Installation).

Interior Trim and Ornamentation, Removal and Installation).

Vehicles with active damping

2. Disconnect the active suspension damper electrical connector.













All vehicles

3. Remove the shock absorber and spring assembly top mount
nuts. TORQUE: 28 Nm













4. WARNING: Make sure to support the vehicle with axle stands.
Raise the vehicle.

5. Remove the wheel and tire.
For additional information, refer to: Wheel and Tire (204-04 Wheels and Tires, Removal and Installation).

3. WARNINGS:


Make sure the shock absorber is secured by fully
inserting the locking pin in to the special tool. Failure to
follow these instructions may result in personal injury.


As the spring is under extreme tension care must be
taken at all times. Failure to follow these instructions may
result in personal injury.


Make sure that a new nut is installed.

Using the special tool, compress the suspension spring to
install the shock absorber.
Compress the spring.
Tighten the nut to 50 Nm.

4. Install the shock absorber and spring assembly.
Tighten to 133 Nm.












5. Install the wheel and tire.
For additional information, refer to: Wheel and Tire (204-04 Wheels and Tires, Removal and Installation).

All vehicles

6. Install the shock absorber and spring assembly top mount
nuts.
Tighten to 28 Nm.














Vehicleswithoutactivedamping

Rear Suspension - Rear Stabilizer Bar
Removal and Installation Published: 06-Jun-2013



Removal

1. Disconnect the battery ground cable.
For additional information, refer to: Battery Disconnect and Connect (414-01 Battery, Mounting and Cables, General Procedures).


2. WARNING: Make sure to support the vehicle with axle stands.
Raise and support the vehicle.

3. Remove both rear wheels and tires.
For additional information, refer to: Wheel and Tire (204-04 Wheels and Tires, Removal and Installation).

4. Drain the fuel tank.
For additional information, refer to: Fuel Tank Draining (310-00 Fuel System - General Information, General Procedures).

5. Remove the exhaust system.
For additional information, refer to: Front Muffler (309-00B Exhaust System - V6 3.0L Petrol, Removal and Installation).


6. CAUTION: Always plug any open connections to
prevent contamination.
NOTES:


To prevent the loss of brake fluid, using the special
tool apply the brake pedal and set to 40mm ( 1.6 in ) below
the rest position.


RH illustration shown, LH is similar.
Disconnect the brake hose from the brake caliper.
Using the special tool, press and hold the brake
pedal.
Remove and discard the two sealing washers. Powertrain Assembly Jack, HTJ
1200-2 Special Tool(s)

7. NOTE: Left-hand shown, right-hand similar.

Release the brake caliper.
Remove and discard the 2 bolts.
Tie the brake caliper aside.












8. NOTE: Left-hand shown, right-hand similar.
Disconnect the rear wheel speed sensor.











9. Disconnect the electronic parking brake actuator electrical
connector.













10. NOTE: Left-hand shown, right-hand similar.

Disconnect both parking brake cables from the rear brake
calipers.

System - V6 3.0L Petrol, Removal and Installation).

19. Refill the fuel tank.
For additional information, refer to: Fuel Tank Draining (310-00 Fuel System - General Information, General Procedures).

20. Bleed the brake system.
For additional information, refer to: Brake System Bleeding (206-00 Brake System - General Information, General Procedures).

21. Install the rear wheels and tires.
For additional information, refer to: Wheel and Tire (204-04 Wheels and Tires, Removal and Installation).

22. Connect the battery ground cable.
For additional information, refer to: Battery Disconnect and Connect (414-01 Battery, Mounting and Cables, General Procedures).

23. Using only four-wheel alignment equipment approved by Jaguar, check
and adjust the wheel alignment.
For additional information, refer to: Camber and Caster Adjustment (204-00 Suspension System - General Information, General Procedures).

204-269
Flange remover forcing screw

204-305
Remover, Wheel Bearing

204-725
Support Tool, Wheel Hub

204-726
Remover/Installer, Wheel Bearing

204-727A
Installer, Wheel Bearing

205-491
Hub puller

205-491-1
Adapter nuts Removal


1. WARNING: Make sure to support the vehicle with axle stands.
Raise and support the vehicle.

2. Refer to: Wheel and Tire (204-04 Wheels and Tires, Removal and Installation).

3.