2010 JAGUAR XFR Supercharger

Published: 30-Jan-2014
Intake Air Distribution and Filtering - V8 S/C 5.0L Petrol - Supercharger
Removal and Installation

Special Tool(s)


303-1449-01
Supercharger Installation Guide Pins - Threaded

303-1449-02
Supercharger Installation Guide Pins - Unthreaded Removal


CAUTION: If a new cylinder head has been installed, then new taptite bolts must be used to install the supercharger.
NOTES:


New taptite bolts when used cut their own threads on the first application.


Removal steps in this procedure may contain installation details.

1. Refer to: Battery Disconnect and Connect (414-01 Battery, Mounting and Cables, General Procedures).


2. WARNING: Do not work on or under a vehicle supported only by a jack.
Always support the vehicle on safety stands.
Raise and support the vehicle.

3. Refer to: Charge Air Cooler (303-12D Intake Air Distribution and Filtering - V8 S/C 5.0L Petrol, Removal and Installation).

4. Refer to: Throttle Body (303-04E Fuel Charging and Controls - V8 S/C 5.0L Petrol, Removal and Installation).

5. Refer to: Supercharger Belt (303-05 Accessory Drive - 5.0L, Removal and
Installation).

6. Refer to: Manifold Absolute Pressure (MAP) Sensor (303-14D Electronic Engine Controls - V8 S/C 5.0L Petrol, Removal and Installation).

Installation 13.

















14.


1. CAUTION: If a new cylinder head has been installed, then new
taptite bolts must be used to install the supercharger.


NOTE: New taptite bolts when used cut their own threads on the
first application.
To install, reverse the removal procedure.

2. Torque: 25 Nm

3. Torque: 25 Nm 4. Torque: 10 Nm 5.
6.
CAUTIONS:


If a new cylinder head has been installed then
the special tool 303-1449-02 without the thread
must be used to install the supercharger.


If a new cylinder head has been installed, then
new taptite bolts must be used to install the
supercharger.


NOTE: New taptite bolts when used cut their
own threads on the first application.

Engine Controls - V8 S/C 5.0L Petrol, Removal and Installation).

14. Refer to: Supercharger Belt (303-05 Accessory Drive - 5.0L, Removal and
Installation).

15. Refer to: Throttle Body (303-04E Fuel Charging and Controls - V8 S/C 5.0L Petrol, Removal and Installation).

16. Refer to: Charge Air Cooler (303-12D Intake Air Distribution and Filtering - V8 S/C 5.0L Petrol, Removal and Installation).

17. Refer to: Battery Disconnect and Connect (414-01 Battery, Mounting and Cables, General Procedures). www.JagDocs.com

Published: 20-Jun-2014
Intake Air Distribution and Filtering - V8 S/C 5.0L Petrol - Supercharger
Spring Isolator
Removal and Installation

Removal


CAUTION: Make sure that all open ports are covered to prevent any foreign material ingress.


NOTE: Some variation in the illustrations may occur, but the essential information is always correct.


1. WARNING: Make sure to support the vehicle with axle stands.
Raise and support the vehicle.

2. Refer to: Supercharger (303-12D Intake Air Distribution and Filtering - V8 S/C 5.0L Petrol, Removal and Installation).

3.

11.
12. Torque: 20 Nm























Remove the installation tool.



















13. CAUTIONS:


Make sure that spring resistance is felt in both directions of the
pulley as shown.


Make sure that all open ports are covered to prevent any foreign
material ingress.


NOTE: Supercharger rotors will appear polished, this is normal.

16. Refer to: Supercharger (303-12D Intake Air Distribution and Filtering - V8 S/C 5.0L Petrol, Removal and Installation).

NOTE: System on supercharger vehicle shown, system on naturally aspirated vehicle similar. 1 EVAP (evaporative emissions) canister 2 Vapor pipe - fuel tank to EVAP canister 3 Vapor pipe - EVAP canister to EVAP canister purge valve 4 EVAP canister purge valve