2010 CADILLAC ESCALADE warning

Rear Position
Rear Tire Flat:If the flat tire is on a rear tireof the vehicle, you will need to use the jackhandle (B) and both jack handle extensions (C).Attach the wheel wrench (D) to the jack handleextensions (C). Attach the jack handle (B) to thejack (A). Use the jacking pad (E) provided on therear axle. Turn the wheel wrench (D) clockwise toraise the vehicle. Raise the vehicle far enough offthe ground so there is enough room for the sparetire to clear the ground.
5. Remove all of thewheel nuts.
6. Take off the flat tire.
{WARNING:
Rust or dirt on a wheel, or on the parts to which it
is fastened, can make wheel nuts become loose
after time. The wheel could come off and cause
an accident. When changing a wheel, remove any
rust or dirt from places where the wheel attaches
to the vehicle. In an emergency, use a cloth or a
paper towel to do this; but be sure to use a
(Continued)
7-88

WARNING: (Continued)
scraper or wire brush later, if needed, to get
all the rust or dirt off. SeeChanging a
Flat Tire on page 7!80.
7. Remove any rust or dirtfrom the wheel bolts,mounting surfaces, andspare wheel.
{WARNING:
Never use oil or grease on bolts or nuts because
the nuts might come loose. The vehicle's wheel
could fall off, causing a crash.
8. Put the wheel nuts back on with the rounded endof the nuts toward the wheel after mounting thespare tire.
9. Tighten each wheel nut by hand. Then use thewheel wrench to tighten the nuts until the wheel isheld against the hub.
7-89

10. Turn the wheel wrench counterclockwiseto lower the vehicle. Lower the jackcompletely.
{WARNING:
Wheel nuts that are improperly or incorrectly
tightened can cause the wheels to become loose
or come off. The wheel nuts should be tightened
with a torque wrench to the proper torque
specification after replacing. Follow the torque
specification supplied by the aftermarket
manufacturer when using accessory locking wheel
nuts. SeeCapacities and Specificationson
page 7!115for original equipment wheel nut
torque specifications.
Notice:Improperly tightened wheel nuts can leadto brake pulsation and rotor damage. To avoidexpensive brake repairs, evenly tighten the wheelnuts in the proper sequence and to the propertorque specification. SeeCapacities andSpecificationson page 7!115for the wheel nuttorque specification.
11. Tighten the nuts firmlyin a crisscrosssequence as shownby turning the wheelwrench clockwise.
When you reinstall the regular wheel and tire, you mustalso reinstall the center cap. Line the tab on the back ofthe cap with the slot in the wheel. Place the cap on thewheel and press until it snaps into place.
7-90

Secondary Latch System
Your vehicle has an underbody-mounted tire hoistassembly equipped with a secondary latch system. It isdesigned to stop the spare tire from suddenly falling offyour vehicle. For the secondary latch to work, the sparemust be installed with the valve stem pointing down.SeeStoring a Flat or Spare Tire and Toolsonpage 7!94.
{WARNING:
Before beginning this procedure read all the
instructions. Failure to read and follow the
instructions could damage the hoist assembly and
you and others could get hurt. Read and follow
the instructions listed next.
To release the spare tire from the secondary latch:
1. Check under thevehicle to see if thecable end is visible.If the cable is notvisible proceed toStep 6.
2. If it is visible, first try to tighten the cable byturning the wheel wrench clockwise until youhear two clicks or feel it skip twice. You cannotovertighten the cable.
3. Loosen the cable by turning the wrenchcounterclockwise three or four turns.
7-91

9. Position the center lift point of the jack under thecenter of the spare tire.
10. Turn the wrench clockwise to raise the jack until itlifts the end fitting.
11. Continue raising the jack until the spare tire stopsmoving upward and is held firmly in place. Thesecondary latch has released and the spare tire isbalancing on the jack.
12. Lower the jack by turning the wheel wrenchcounterclockwise. Keep lowering the jack until thespare tire slides off the jack or is hanging by thecable.
{WARNING:
Someone standing too close during the procedure
could be injured by the jack. If the spare tire does
not slide off the jack completely, make sure no
one is behind you or on either side of you as you
pull the jack out from under the spare.
13. Disconnect the jack handle from the jack andcarefully remove the jack. Use one hand to pushagainst the spare while firmly pulling the jack outfrom under the spare tire with the other hand.
If the spare tire is hanging from the cable, insertthe hoist end of extension, and wheel wrench intothe hoist shaft hole in the bumper and turn thewheel wrench counterclockwise to lower the sparethe rest of the way.
14. Turn the wheel wrench in the hoist shaft hole in thebumper clockwise to raise the cable back up if thecable is hanging under the vehicle.
Have the hoist assembly inspected as soon as you can.You will not be able to store a spare or flat tire using thehoist assembly until it has been inspected and/orreplaced.
To continue changing the flat tire, seeRemoving theFlat Tire and Installing the Spare Tire on page 7!86.
7-93

Storing a Flat or Spare Tire
and Tools
{WARNING:
Storing a jack, a tire, or other equipment in the
passenger compartment of the vehicle could
cause injury. In a sudden stop or collision, loose
equipment could strike someone. Store all these
in the proper place.
Notice:Storing an aluminum wheel with a flat tireunder your vehicle for an extended period of time orwith the valve stem pointing up can damage thewheel. Always stow the wheel with the valve stempointing down and have the wheel/tire repaired assoon as possible.
Store the tire under the rear of the vehicle in the sparetire carrier.
A. Hoist Assembly
B. Hoist Shaft
C. Hoist Shaft AccessCover/Hole
D. Jack HandleExtensions
E. Wheel Wrench
F. Hoist Cable
G. Tire/Wheel Retainer
H. Spare Tire/Flat Tire (ValveStem Pointed Down)
I. Hoist ShaftAccess Hole
J. Hoist End ofExtension Tool
K. Spare Tire Lock
7-94

Care of Safety Belts
Keep belts clean and dry.
{WARNING:
Do not bleach or dye safety belts. It may severely
weaken them. In a crash, they might not be able
to provide adequate protection. Clean safety belts
only with mild soap and lukewarm water.
Weatherstrips
Silicone grease on weatherstrips will make them lastlonger, seal better, and not stick or squeak. Applysilicone grease with a clean cloth. During very cold,damp weather frequent application may be required.SeeRecommended Fluids and Lubricantsonpage 8!10.
Washing Your Vehicle
The best way to preserve the vehicle's finish is to keepit clean by washing it often.
Notice:Certain cleaners contain chemicals that candamage the emblems or nameplates on the vehicle.Check the cleaning product label. If it states that itshould not be used on plastic parts, do not use it onthe vehicle or damage may occur and it would notbe covered by the warranty.
Do not wash the vehicle in direct sunlight. Use a carwashing soap. Do not use cleaning agents that arepetroleum based or that contain acid or abrasives, asthey can damage the paint, metal or plastic on thevehicle. Approved cleaning products can be obtainedfrom your dealer/retailer. Follow all manufacturers'directions regarding correct product usage, necessarysafety precautions and appropriate disposal of anyvehicle care product.
Rinse the vehicle well, before washing and after toremove all cleaning agents completely. If they areallowed to dry on the surface, they could stain.
Dry the finish with a soft, clean chamois or an all-cottontowel to avoid surface scratches and water spotting.
7-102

Maintenance Schedule
Introduction
Notice:Maintenance intervals, checks, inspections,recommended fluids, and lubricants are necessaryto keep this vehicle in good working condition.Damage caused by failure to follow scheduledmaintenance might not be covered by the vehiclewarranty.
Proper vehicle maintenance helps to keep the vehicle ingood working condition, improves fuel economy, andreduces vehicle emissions for better air quality.
Because of all the different ways people use vehicles,maintenance needs vary. The vehicle might need morefrequent checks and services. Please read theinformation under Scheduled Maintenance. To keep thevehicle in good condition, see your dealer/retailer.
The maintenance schedule is for vehicles that:
.carry passengers and cargo within recommendedlimits on the Tire and Loading Information label.SeeLoading the Vehicle on page 6!32.
.are driven on reasonable road surfaces within legaldriving limits.
.are driven off!road in the recommended manner.SeeOff-Road Driving on page 6!13.
.use the recommended fuel. SeeGasoline Octaneo n p a g e 7!8.
{WARNING:
Performing maintenance work on a vehicle can be
dangerous. In trying to do some jobs, you can be
seriously injured. Do your own maintenance work
only if you have the required know-how and the
proper tools and equipment for the job. If you
have any doubt, see your dealer/retailer to have a
qualified technician do the work. SeeDoing Your
Own Service Work on page 7!6.
8-2