2010 CADILLAC ESCALADE transmission fluid

4. Allow the engine to idle (500–800 rpm) for at leastone minute. Slowly release the brake pedal.
5. Keep the engine running and press the Trip/Fuelbutton or trip odometer reset stem until TRANSTEMP (Transmission Temperature) displays on theDriver Information Center (DIC).
6. Using the TRANS TEMP reading, determine andperform the appropriate check procedure. If theTRANS TEMP reading is not within the requiredtemperature ranges, allow the vehicle to cool,or operate the vehicle until the appropriatetransmission fluid temperature is reached.
Cold Check Procedure
Use this procedure only as a reference to determine ifthe transmission has enough fluid to be operated safelyuntil a hot check procedure can be made. The hotcheck procedure is the most accurate method to checkthe fluid level. Perform the hot check procedure at the
first opportunity. Use this cold check procedure to checkfluid level when the transmission temperature isbetween 80°F and 90°F (27°C and 32°C).
1. Locate thetransmission dipstick atthe rear of the enginecompartment, on thepassenger side of thevehicle.
SeeEngine Compartment Overviewon page 7!16for more information.
2. Flip the handle up and then pull out the dipstickand wipe it with a clean rag or paper towel.
3. Install the dipstick by pushing it back in all the way,wait three seconds, and then pull it back out again.
4. Check both sides of the dipstick and read the lowerlevel. Repeat the check procedure to verify thereading.
7-25

5. If the fluid level is below the COLD check band,add only enough fluid as necessary to bring thelevel into the COLD band. It does not take muchfluid, generally less than one pint (0.5L). Do notoverfill.
6. Perform a hot check at the first opportunity afterthe transmission reaches a normal operatingtemperature between 160°F to 200°F (71°Cto 93°C).
7. If the fluid level is in the acceptable range, pushthe dipstick back in all the way, then flip the handledown to lock the dipstick in place.
Hot Check Procedure
Use this procedure to check the transmission fluid levelwhen the transmission fluid temperature is between160°F and 200°F (71°C and 93°C).
The hot check is the most accurate method to check thefluid level. The hot check should be performed at thefirst opportunity in order to verify the cold check. Thefluid level rises as fluid temperature increases, so it isimportant to ensure the transmission temperature iswithin range.
1. Locate thetransmission dipstick atthe rear of the enginecompartment, on thepassenger side of thevehicle.
SeeEngine Compartment Overviewon page 7!16for more information.
2. Flip the handle up and then pull out the dipstickand wipe it with a clean rag or paper towel.
3. Install the dipstick by pushing it back in all the way,wait three seconds, and then pull it back out again.
7-26

4. Check both sides of the dipstick and readthe lower level. Repeat the check procedureto verify the reading.
5. Safe operating level is within the HOT cross hatchband on the dipstick. If the fluid level is not withinthe HOT band, and the transmission temperatureis between 160°F and 200°F (71°C and 93°C), addor drain fluid as necessary to bring the level intothe HOT band. If the fluid level is low, add onlyenough fluid to bring the level into the HOT band.It does not take much fluid, generally less thanone pint (0.5L). Do not overfill.
6. If the fluid level is in the acceptable range, pushthe dipstick back in all the way, then flip the handledown to lock the dipstick in place.
Consistency of Readings
Always check the fluid level at least twice using theprocedures described. Consistency (repeatablereadings) is important to maintaining proper fluid level.If fluid is added, it may take 15 minutes or longer toobtain an accurate reading because of residual fluiddraining down the dipstick tube. If inconsistent readingspersist, check the transmission breather to be sure it isclean and not clogged. If readings are still inconsistent,contact your dealer/retailer.
7-27

ApplicationCapacities
EnglishMetric
Transmission Fluid (Pan Removal and Replacement)6.0 qt5.7 L
Transfer Case Fluid1.5 qt1.4 L
Wheel Nut Torque140 lb ft190Y
All capacities are approximate. When adding, be sure to fill to the approximate level, as recommended in this manual.Recheck fluid after filling.†Oil filter should be changed at every oil change.
Engine Specifications
EngineVIN CodeTransmissionSpark Plug Gap
6.2L V8FAutomatic0.040 in (1.02 mm)
7-116

Every Engine Oil Change
.Change engine oil and filter. SeeEngine Oilonpage 7!17.An Emission Control Service.
.Engine coolant level check. SeeEngine Coolanton page 7!29.
.Windshield washer fluid level check. SeeWindshield Washer Fluid on page 7!39.
.Tire inflation check. SeeInflation - Tire Pressureon page 7!65.
.Tire wear inspection. SeeTire Inspection andRotation on page 7!71.
.Rotate tires. SeeTire Inspection and Rotationonpage 7!71.
.Fluids visual leak check (or every 12 months,whichever occurs first). A leak in any system mustbe repaired and the fluid level checked.
.Engine air cleaner filter inspection. SeeEngine AirCleaner/Filter on page 7!22.
.Brake system inspection (or every 12 months,whichever occurs first).
.Lubricate the front suspension, steering linkage,and parking brake cable guides. Control arm balljoints are maintenance!free.
.Steering and suspension inspection. Visualinspection for damaged, loose, or missing parts orsigns of wear.
.Engine cooling system inspection. Visualinspection of hoses, pipes, fittings, and clamps andreplacement, if needed.
.Windshield wiper blade inspection for wear,cracking, or contamination and windshield andwiper blade cleaning, if contaminated. SeeWindshield, Backglass, and Wiper Bladesonpage 7!104. Worn or damaged wiper bladereplacement. SeeWindshield Wiper BladeReplacement on page 7!57.
.Body hinges and latches, key lock cylinders, rearcompartment hinges, outer tailgate handle pivotpoints, and folding seat hardware lubrication. SeeRecommended Fluids and Lubricantsonpage 8!10. More frequent lubrication may berequired when vehicle is exposed to a corrosiveenvironment. Applying silicone grease onweatherstrips with a clean cloth makes them lastlonger, seal better, and not stick or squeak.
.Restraint system component check. SeeCheckingthe Restraint Systems on page 2!91.
.Automatic transmission fluid level check andadding fluid, if needed. SeeAutomaticTransmission Fluid on page 7!24.
8-4

Additional Required Services
At Each Fuel Stop
.Engine oil level check. SeeEngine Oilonpage 7!17.
.Engine coolant level check. SeeEngine Coolanton page 7!29.
.Windshield washer fluid level check. SeeWindshield Washer Fluid on page 7!39.
Once a Month
.Tire inflation check. SeeInflation - Tire Pressureon page 7!65.
.Tire wear inspection. SeeTire Inspection andRotation on page 7!71.
Once a Year
.Starter switch check. SeeOwner Checks andServices on page 8!8.
.Parking brake and automatic transmission P (Park)mechanism check. SeeOwner Checks andServices on page 8!8.
.Automatic transmission shiftlock control systemcheck. SeeOwner Checks and Servicesonp a g e 8!8.
.Ignition transmission lock check. SeeOwnerChecks and Services on page 8!8.
.Engine cooling system and pressure cap pressurecheck. Radiator and air conditioning condenseroutside cleaning. SeeCooling Systemonpage 7!28.
.Exhaust system and nearby heat shieldsinspection for loose or damaged components.
.Accelerator pedal check for damage, high effort,or binding. Replace if needed.
.Hood and liftgate support gas strut inspection forsigns of wear, corrosion, cracks, loss of lubricant,or other damage. Check the hold open ability ofthe gas strut. If necessary, replace with genuineparts from your dealer/retailer.
8-5

First Engine Oil Change After Every
40 000 km/25,000 Miles
.Fuel system inspection for damage or leaks.
First Engine Oil Change After Every
80 000 km/50,000 Miles
.Engine air cleaner filter replacement. SeeEngineAir Cleaner/Filter on page 7!22.
.Automatic transmission fluid and filter change(severe service) for vehicles mainly driven in heavycity traffic in hot weather, in hilly or mountainousterrain, when frequently towing a trailer, or used fortaxi, police, or delivery service. SeeAutomaticTransmission Fluid on page 7!24.
.Four!wheel drive only: Transfer case fluid change(severe service) for vehicles mainly driven whenfrequently towing a trailer, or used for taxi, police,or delivery service. Check vent hose at transfercase for kinks and proper installation. Check to besure vent hose is unobstructed, clear, and free of
debris. During any maintenance, if a power washeris used to clean mud and dirt from the underbody,care should be taken to not directly spray thetransfer case output seals. High pressure watercan overcome the seals and contaminate thetransfer case fluid. Contaminated fluid willdecrease the life of the transfer case and shouldbe replaced.
.Evaporative control system inspection. Check allfuel and vapor lines and hoses for proper hook!up,routing, and condition. Check that the purge valve,if the vehicle has one, works properly. Replace asneeded.An Emission Control Service. The U.S.Environmental Protection Agency or the CaliforniaAir Resources Board has determined that thefailure to perform this maintenance item will notnullify the emission warranty or limit recall liabilityprior to the completion of the vehicle's useful life.We, however, urge that all recommendedmaintenance services be performed at theindicated intervals and the maintenance berecorded.
8-6

First Engine Oil Change After Every
160 000 km/100,000 Miles
.Automatic transmission fluid and filter change(normal service). SeeAutomatic TransmissionFluid on page 7!24.
.Four!wheel drive only: Transfer case fluid change(normal service). Check vent hose at transfer casefor kinks and proper installation. Check to be surevent hose is unobstructed, clear, and free ofdebris. During any maintenance, if a power washeris used to clean mud and dirt from the underbody,care should be taken to not directly spray thetransfer case output seals. High pressure watercan overcome the seals and contaminate thetransfer case fluid. Contaminated fluid willdecrease the life of the transfer case and shouldbe replaced.
.Spark plug replacement and spark plug wiresinspection.An Emission Control Service.
First Engine Oil Change After Every
240 000 km/150,000 Miles
.Engine cooling system drain, flush, and refill,cooling system and cap pressure check, andcleaning of outside of radiator and air conditioningcondenser (or every 5 years, whichever occursfirst). SeeEngine Coolanton page 7!29.AnEmission Control Service.
.Engine accessory drive belt inspection for fraying,excessive cracks, or obvious damage andreplacement, if needed.An Emission ControlService.
8-7