Page 297 of 320

_________________________________________________ G_ e_ n_ e_r _a _l_ i_n _f_o _ r_ m_ a_ t _i _o _ n __ _
left door jamb. It shows the month and year of production and the
vehicle identification number of your vehicle (perforation) as well as
the Gross Vehicle Weight Rating (GVWR) and the Gross Axle Weight
Rating (GAWR).
The high voltage warning label
is located on the lock carrier.
The spark ignition system complies with the Canadian
standard ICES-002. •
Weights
Gross Vehicle Weight Rating
The Gross Vehicle Weight Rating (GVWR), and the Gross Axle Weight
Rating (GAWR) for front and rear are listed on a sticker on the left
door jamb.
The Gross Vehicle Weight Rating includes the weight of the basic
vehicle plus full fuel tank, oil and coolant, plus maximum load,
which includes passenger weight (150 lbs/68 kg per designated
seating position) and luggage weight.
Gross Axle Weight Rating
The Gross Axle Weight Rating is the maximum load that can be
applied at each axle of the vehicle ~& .
Vehicle capacity weight
The vehicle capacity weight (max. load) is listed either on the
driver's side B-pillar or inside the fuel filler flap .
Roof weight
The maximum permissible roof weight is 165 lb (75 kgl. The roof
weight is made up of the weight of the roof rack system and the
weight of the object being transported~
page 89, "Loading the
roof rack".
Controls and equip ment Safety first Vehicle operation
& WARNING
•
The actual Gross Axle Weight Rating at the front and rear axles
should not exceed the permissible weights, and their combination
must not exceed the Gross Vehicle Weight Rating.
• Exceeding permissible weight ratings can result in vehicle
damage, accidents and personal injury.
0 Note
• The vehicle capacity weight figures apply when the load is
distributed evenly in the vehicle (passengers and luggage). When
transporting a heavy load in the luggage compartment, carry the
load as near to the rear axle as possible so that the vehicle's
handling is not impaired.
• Do not exceed the maximum permissible axle loads or the
maximum gross vehicle weight. Always remember that the vehicle's
handling will be affected by the extra load. Therefore, adjust your
speed accordingly.
• Always observe local regulations.•
Dimensions
The specifications refer to the basic model. Differences may occur
depending on the model type and options ordered, for example, tire
sizes.
0 Note
When driving up steep ramps, on rough roads, over curbs, etc. it is
important to remember that some parts of your vehicle, such as
spoilers or exhaust system components, may be close to the
ground. Be careful not to damage them. •
Vehicle care Do-it-yourself service Tec hn ica l da ta
Page 298 of 320

___ D_ a_ ta ______________________________________________________ _
Data
Applies to vehi cles: with 2.0 lite r TFS I 4-cyl. g asoline eng ine ,
200 hp, 2.0 liter 4-cyl. turbo gasoline engine
Engin e data
Maximum output SAE net
Maximum torque SAE net
No. of cy linders
Disp lacement
Stroke
Bore
Compression ratio
Fuel
D im ensio ns (a pprox.)
Length (with licence plate bracket)
Width (across mirrors)
Height (unladen, incl. roof rails)
Turning circle diameter (curb to cu rb)
Ca pacitie s (a pprox.)
F u el t ank
-Total capacity
- Reserve (of total capacity)
W ind shi eld was her fluid cont ain er
Engine oil
with filter change hp@rpm
lb
-ft@ rpm
CID (cm
3 )
in (mm)
in (mm)
200@ 5100 -6000
207 @ 1700 -5000
4 121 (1984)
3.65 (92.8)
3 .25 (82 .5)
9 .6 : 1
Premium unleaded (91 AKI) Recommended for maximum engine performance . Fur
ther det ails =:>
page 277, "Gasol ine"
in (mm)
in (mm)
in (mm)
ft. (ml
168.9 (4292)
78 .5 (1995)
56.0 (1423)
35.1 (10.7)
gal/liters
gal/liters
quarts/liters
quarts/liters 14 .6 / 55.0
1 .8/7.0
3 .1 / 3 .0
4 .8 / 4.6
•
Page 299 of 320

___________________________________________________ D_a_ t_ a __ !II
A pp lies to veh ic les : w it h 2 .0 liter TDI 4 -cyl. c le an di esel e ngin e,
140 hp , 2 .0 TOI liter 4-cyl. turbo clean diesel engine
Engine data
Maximum output SAE net
Maximum torque SAE net
N o. o f cy linders
Displacement
Stroke
Bore
Co mpression ratio
Fuel
Dimensions (approx .)
Length (with licence p late bracket)
Width (across mirrors) H eight (unla den, incl. roof ra ils)
Turning circle diameter (curb to curb)
Capacities (approx .)
Fuel tank
-Total capacity
- Reserve (of t otal capacity)
Wind shield wa sher fluid container
Engine oil
with filter change
Controls and equip ment Safety first
hp@rpm
lb-ft@ rpm
CID (cm
3
)
in (mm)
in (mm)
14 0 @4200
236 @ 1750 · 2500
4
120.1 (1968)
3 .76 (95 .5)
3.19 (81 .0)
16. 5: 1
ULSD Diesel No . 2 Further details=> page 218, "Diesel fue l"
in (mm)
in (mm)
in ( mm)
ft. (ml
Vehicle operation
168.9 (4292)
78.5 (1995) 56.0 (14 23)
35.1 (10.7)
gal/liters
gal/li te rs
quarts/liters
quarts/liters
Vehicle care
14.6 / 55.0 1.8/7.0
3.1 / 3_0
4.2 I 4 .0
Do-it-yourself service
•
T ec hn ica l da ta
Page 300 of 320

___ C_ o_n_ s_ u_m _ e_ r_ ln_ f_ o _r _m _ a_ t_ i_o _n ______________________________________________ _
Consumer Information
Warranty coverages
Your A udi i s cov ered b y the follo wing war ra nt ies:
• New Vehicle Limited Warranty
• Limited Warranty Against Corrosion Perforation
• Emissions Control System Warranty
• Emissions Performance Warranty
• California Emissions Control Warranty (USA vehicles only)
• California Emissions Performance Warranty (USA vehicles only)
Detailed information rega rding your warranties can be found in
your
W arr ant y & Maint ena nce Booklet .•
Operating your vehicle outside the
U .S.A. or Canada
Government regulations in the United States and Canada require
that automobiles meet specific em ission regulations and safety
standards. Therefore, vehic les bui lt for the U.S .A. and Canada differ
from vehicles sold in other countries .
If you plan to take your vehic le outside the continental limits of the
United States or Canada, there is the possibility that
• unleaded fue ls for vehicles with catalyt ic converter may not be
available;
• f uel may have a considerably lower octane rating . Improper fuel
may cause engine damage;
• service may be inadequate due to lack of proper service facilities,
tools or testing equipment;
• replacement parts may not be readi ly available . •
Navigation systems for vehicles built for the U.S.A . and Canada
wil l not necessarily work in Europe, and may not work in other coun
tries outside of North Amer ica.
Audi c annot be responsib le for me ch an ical damage that could
result from inadequate fuel , serv ice or parts availability .
0 Note
Audi cannot be responsible fo r mechanica l damage that could
result from inadequate fuel, service or parts avai lability .•
Audi Service Repair Manuals and
Literature
Audi Official Factory Service Manuals are published as soon as
possible af ter model introduction . Service manua ls are available
from:
Audi Te ch n ic al Liter ature Ordering Center
Ca ll toll -free:
Tel. :
1 (800) 544-802 1
(from 8:00 AM to 8:00 PM, EST, Mon day t hrough Friday)
or access their website
www .audi .dd sltd .com on the Internet to
order repair manuals and other Audi literature .•
Page 301 of 320

Consumer Information I'll _________________________________ __::..::....:...:...::...:.:..:....:....:.:;__ _____ _
Maintenance
General
Your vehicle has been designed to help keep maintenance require
ments to a minimum.
However, a certain amount of regular maintenance is still necessary
to assure your vehicle's safety, economy and reliability.
For detailed vehicle maintenance consult your Warranty
& Mainte
nance booklet.
Under difficult operating conditions, for example at extremely low
outside temperatures, in very dusty regions, when towing a trailer
very frequently, etc., some service work should be performed
between the intervals specified. This applies particularly to:
• oil changes, and
• cleaning or replacing the air filter.
ci> For the sake of the environment
By regularly maintaining your vehicle, you help make sure that emis
sion standards are maintained, thus minimizing adverse effects on
the environment. •
Important considerations for you and your
vehicle
The increasing use of electronics, sophisticated fuel injection and
emission control systems, and the generally increasing technical
complexity of today's automobiles, have steadily reduced the scope
of maintenance and repairs which can be carried out by vehicle
owners.
Also, safety and environmental concerns place very strict
limits on the nature of repairs and adjustments to engine and trans
mission parts which an owner can perform.
Controls and equip
ment Safety first Vehicle operation
Maintenance, adjustments and repairs usually require special tools,
testing devices and other equipment available to specially trained
workshop personnel in order to assure proper performance, reli ability and safety of the vehicle and its many systems.
Improper maintenance, adjustments and repairs can impair the
operation and reliability of your vehicle and even void your vehicle
warranty. Therefore, proof of servicing in accordance with the main tenance schedule may be a condition for upholding a possible
warranty claim made within the warranty period.
Above all, operational safety can be adversely affected, creating unnecessary risks for you and your passengers.
If in doubt about any servicing, have it done by your authorized Audi
dealer or any other properly equipped and qualified workshop. We
strongly urge you to give your authorized Audi dealer the opportu
nity to perform all scheduled maintenance and necessary repairs.
Your dealer has the facilities, original parts and trained specialists
to keep your vehicle running properly .
Performing limited maintenance yourself
The following pages describe a limited number of procedures which
can be performed on your vehicle with ordinary tools, should the
need arise and trained personnel be unavailable. Before performing
any of these procedures, always thoroughly read all of the appli
cable text and carefully follow the instructions given. Always rigor
ously observe the
WARNINGS provided.
Before you check anything in the engine compartment, always read
and heed all WARNINGS=>
& and=> & in "Working in the engine
compartment" on
page 224.
& WARNING
• Serious personal injury may occur as a result of improperly
performed maintenance, adjustments or repairs.
Vehicle care Do-it-yourself service Tec hn ica l da ta
Page 302 of 320

___ C_ o_n_ s_ u_m _ e_ r_ ln_ f_o _r_m _ a_ t_ i_o _n ______________________________________________ _
& WARN ING (continued )
• Always be extremely careful when working on the vehicle.
Alway s follow commonly a ccepted safety practices and general
c ommon sen se . Never risk per sonal injury .
• Do not attempt any of the maintenance, checks or repairs
described on the following pages if you are not fully familiar with
the se or other procedures with re spect to the vehicle , or are uncer
tain how to proceed .
• Do not do any work without the proper tools and equipment.
Have the necessary work done by your authorized Audi dealer or
another properly equipped and qualified work shop .
• The engine compartment of any motor vehicle is a potentially
hazardous area . Never reach into the a rea around or touch the
radiator fan. It is temperature controlled and can switch on
suddenly · even when the engine is off and the ignition key has
been removed . The radiator fan switches on automatically when
the coolant reaches a certain temperature and will continue to run
until the coolant temperature drops .
• Always remove the ign ition key before anyone gets under the
vehicle .
• Always support your vehicle with safety stands if it is neces
sary to work underneath the vehicle. The jack supplied with the
vehicle is not adequate for this purpose and could collap se
c ausing serious personal injury .
• If you must work underneath the vehicle with the wheel s on
the ground , always make sure the vehicle is on level ground , that
the wheels are always securely blocked and that the engine c annot be started .
• Always make sure the tr ansmission selecto r lever (automatic
transmission ) is in "P" (Park position ) (automatic transmission ) or
Neutral (manual transmi ssion) and the hand brake is firmly
applied .
W For the sake of the environment
• Cha nging t he en gine setti ngs will adversely a ffec t emi ssio n
l evels. This is detrimenta l to the environment and increases fuel
consumptio n.
• Always o bse rve enviro nmenta l regu lations when dis posing of
o ld eng ine o il, used brake flu id, d irty eng ine coola nt, spe nt batter ies
or worn out tires .
• Undeployed airbag modules and pretensioners might be classi
fied as Pe rchlorate Mate rial -specia l handl ing may apply, see
www .dtsc.ca.gov/ hazardouswaste/perchlora te. W hen t he veh icle or
parts of the restraint system including airbag modu les safety belts
w ith pretens ione rs are sc rapped, all appl icab le laws and regu la
tions must be observed. Your authorized Audi dea ler is familiar with
th ese requi reme nts a nd we reco mme nd t hat you have your dealer
perform this service for you. •
Additional accessories,
modifications and parts replacement
Additional accessories and parts
replacement
A lways co ns ult an author ized Audi d eal er befor e
purc hasing accessorie s.
Your vehicle incorporates the latest safety design features ensuring
a h igh s tanda rd of act ive and pass ive sa fety.
T his safety could be compromised by non -approved changes to the
veh ic le . Fo r thi s reason, if pa rts have to be re place d, please o bserve
the fo llowing points w hen insta lli ng additional accessories:
Approved Audi accessories and genuine Audi parts are avai lable
from autho rized Aud i dea lers.
~
Page 303 of 320

__________________________________________________ C_ o_ n_ s_ u _m _ e_ r_ l_n _f _o _ r_ m_ a_ t_io _ n __ lJIII
T hese dealers also have the necessary faci lities, too ls and trained
specialists to instal l the parts and accessories proper ly .
& WARNING
Using th e wrong spare p art s non -approved acc essorie s can cau se
d amag e to the vehi cle an d se rious per son al injur y.
• Use onl y accessories ex pr ess ly a ppr oved b y Audi and genuine
Audi sp are part s
• The se p art s a nd accesso ries hav e been speci ally des igned to
be u sed on your vehi cle.
• Nev er in sta ll accesso ries s uch as telephone cradle s or
be verage holder s on airbag cover s or within the airb ag deploy
ment zone s. Doing so w ill in creas e the risk of injury if airb ag s a re
trig gered in an ac cident!
• Before you che ck anything in the en gin e c omp artmen t, alw ays
read and heed all WARNINGS=>
page 215 .
0 Note
• I f items other than genuine Audi spare parts, add -on equipment
and accessory items are used or if repair work is not performed
according to specified methods, this can resu lt in severe damage to
your vehicle's eng ine and body (such as corrosion) and adversely
affect your vehicle's warranty .
• If emergency repairs must be performed elsewhere, have the
vehicle examined by an authorized Audi dea lership as soon as
poss ible.
• The manufacturer cannot be held liable for damage which occurs
due to failure to comply with these stipu lations .•
Installing /replacing a sound system
If you wish to install a radio or replace the factory installed radio ,
please note the following :
Controls and equip
ment Safety first Vehicle operation
The factory insta
lled radio connectors are designed for genuine
Audi radios. When install ing a different radio, difficu lties could arise
such as :
- the radio may not fit into the space provided
- the electrical connections may not be compatible
- different connector terminals may be needed .
Therefore, we recommend that you have your authorized Audi dea ler instal l or replace the radio.
They are the most fami liar with the technical features of your
vehic le . They also offer Genuine Audi Radios with the necessary
installa tion components and instructions .
& WARNING
Improperly in stall ing a r adio could cau se a s hort circ uit and an
el ectr ic a l fir e. •
Technical Modifications
Our guidelines must be complied with when technical
mo difications are made.
Always consult an authorized Audi dea ler b efore starting work on
any modifications.
This will help ensure that vehic le function, perfo rmance and safe ty
are not impaired=> &.
Attempting to work on electronic components and the software used with them can cause malfunctions. Because of the way elec
tronic components are interconnected with each other, such
malfunctions can also have an adverse affect on other systems that
are not directly involved . This means that you risk both a substantial
reduction in the operat ional safety of your vehicle and an increased
wear of vehicle par ts
=> & . .,_
Vehicle care Do-it-yourself service Tec hn ica l da ta
Page 304 of 320

___ C_ o_n_ s_ u_m _ e_ r_ ln_ f_ o _r _m _ a_ t_ i_o _n ______________________________________________ _
Authorized Audi dealers will perform this work in a professional and
competent manner or, in special cases, refer you to a professional
company that specializes in such modifications.
& WARNING
Impr oper r ep airs a nd m odificat io ns ca n cha nge the wa y vehi cle
syst ems w ork and cau se s erious per so na l inju ry.
0 Note
If emergency repairs must be performed elsewhere, have the
vehic le examined by an authorized Audi dealership as soon as
possible. •
Declaration of Compliance ,
Telecommunications and Electronic Systems
Radio Frequency Devices and Radiocommunication
Equipment User Manual Notice.
The manufacturer is not responsib le for any radio or TV interference
caused by unauthorized modifications to this equipment .
Devices
The fol lowing devices each comply with FCC Part 15.19, FCC Part
15.21 and RSS-Gen Issue 1:
• Cell phone package
• Electronic immobi lizer
• Homelink® universal remote control
• Remote contro l key
• Tire pressure monitoring system*
FCC Part 15 .1 9
This device complies with part 15 of the FCC Rules. Operation is
subject to the fo llowing two conditions: (1 l This device may not cause harmful interference, and
(2) this device must accept any interference received, including
interference that may cause undesired operation.
F
CC Part 1 5. 21
CAUTION:
Changes or modifications not expressly approved by the party
responsible for compliance cou ld void the user's author ity to
operate the equipment.
R SS-Gen Iss ue 1
Operation is subject to the following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference
that may cause undesired operation of the device .•