2010 AUDI A5 CABRIOLET check engine

Driver information display
When a yellow warning symbol appears, one warning tone sounds. A
dr iver message appears as well to explain the ma lfunction in more
detail. The driver warning goes out after about 5 seconds, but it can
be brought up at any time by pressing the !SET] button again.
Check the function displayed as soon as possible. The yellow symbol
will not go out again until the reason for the malfunction has been
corrected.
If several priority 2 malfunctions are present, the symbols appear in
succession and remain for about 2 seconds .
Dynamic steer ing*
=:>page 32
'O' I I , Worn brake pads =:>page33
Battery vo ltage => page34
Defective light bulb* =>page34
Check engine oil level => page 35 or
=>page 35
Engine oil sensor malfunction =:>page35
--
Low fuel leve l =>page34
Windshield washer fluid =>page34
level low
Convenience key*
=>page 33
Key not in vehicle
Light/rain sensor defective
=:>page33
--
Dynamic headlight range => page 35
control defective
[{] Tips
Battery in remote control key
Electromechanical
parking brake
Engine speed limitation*
adaptive light defective
Ignition lock malfunction
Adaptive dampers*
Windshield wiper defective
T ire pressure monitoring sys­
tem*
Loss of tire pressure
Tire pressure monitoring sys­
tem* System not available
=>page 38
-
=> page 112
-
=>page 35
=> page 35
=> page 35
=>page 35
=>page 36
-
=> page 315
=> page 315
The speed warnings warning threshold 1 and warning threshold 2
are also yellow symbols in some models. The warning is a lways
shown as a small symbol in the uppe r area of the display
=>page 25. •
Appli es to vehicles : wit h Au di dr iv e se lec t
Dynamic steering r
Dynamic steering: System malfunction

This driver message and the symbol,;;:;,. appear when a system
malfunction occurs during travel. You can continue to drive carefully
at a reduced speed to a qualified workshop. Steering can be more
difficult or sensitive than usual. The steering whee l can also be at an
angle when driving straight .
Dynamic steering: initialization
If this driver message appears and the indicator lightl, is flash ing on
the instrument panel, dynamic steering is being reinitialized . Once
you start the engine after this is finished, the steering wheel wi ll be
easy to move. Re -initializat ion might be necessary if the steering
wheel was moved hard to the left and right while the vehicle was not
moving. The display goes out as soon as initial izat io n is complete.
& WARNING
Have the dynamic steering system malfunction repaired as soon
as possible by an authorized Audi dealer or any qualified workshop
- risk of accident!
[I) Tips
The dynamic steer ing stability systems are not ava ilab le in the event
of a system ma lfunct ion .•
Ap plies to ve hicles : w it h c onven ien ce key
Key not in vehicle
Key not in vehicle
This reminder appears along with the symbol if the master key is
removed from the vehicle with the engine running. It is int ended to
remind you (e.g. when chang ing drivers) not to continue the journey
without the master key.
If the master key is no longer in the veh icle, you cannot sw itch off the
ignition after stopping the engine and you a lso cannot start the
engine again. You also cannot lock the veh icle from the outs ide .•
Controls and equip ­
ment Safety first
Driver information display
Light/rain sensor defective
·)
Automatic headlights/automatic wipers defective
If the symbol ill um inates , the light sensor has failed. For safety
reasons the low beams are turned o n permanently with the switch in
AUTO . However, you can continue to turn the lights on and off using
the light switch . In the case of a defect in the ra in sensor, the wind ­
shield wiper lever functions are still avai lable . Have the light/rain
sensor checked as soon as possib le by an autho rized Audi dealer. •
Worn brake pads ~
Brake pads!
If the warning light illuminates, immediately contact your authorized
Audi dealer or qualified workshop to have all brake pads inspected .
On USA mode ls the warning light comes on together with the
war ning light BRAKE . Both sets of b rake pads on an axle must always
be replaced at the same time.
& WARNING
Driving with bad brakes can cause a collision and serious personal
injury .
• If the warning light and the warning light
BRAKE1> with the
message Brake pads! comes on in the instrument cluster display,
immediately contact your authorized Audi dealer or qualified
workshop to have all brake pads checked or replaced if necessary. •
ll BRAKE : USA mode ls on ly
Vehicle care Technical data

Check engine oil 1o
Please top off with ma x. ll of o il. You can keep dri ving.
If the ~ symbo l lights up displaying t his drive r message, t hen ad d a
maximum of
1 liter at your earliest opportunity~ page 285. •
Engine oil level i!:r..,
Please check oil level
When the symbol i lluminates, check the engine oi l level as soo n as
poss ible ~
page 284. Top off the oil at your earliest o pportunity
~ page 285. •
Engine oil sensor defective
" Oil level! Sensor defective
If the symbo l illumina tes, contact your author ized A udi dealer and
have the o il sensor inspected. Until you have this done, check the oil
level each tim e yo u refue l ju st to be on the s afe side ~
page 28 4. •
A pplies t o veh icl es: with eng ine s peed lim itat io n
Engine speed limitation 71
Do not e xceed ma x. engine speed of XXXX rpm
Th e ~ symbo l ill uminates whe n there is an engi ne con trol malfunc­
t ion . The ind icator light
Er"" in the instr ument cluster also i llum inates .
Th e engine speed is limited to the s peed disp laye d in the driver info r­
mation system . Keep in m ind that the engine speed will not exceed
the value disp layed in the driver information system, for examp le
w hen downshifti ng.
Please go to a n author ized Audi dealer or other qualified workshop to
h ave the mal func tion rep aired .•
Controls and equip ­
ment Safety first
Driver information display
• Headlight range control defective
)
Headlight range control defective !
If the sym bo l ~ ill um ina tes, the dynam ic he adl ight range con tro l is
no lo nger work ing properly . H ave t he system checked and repa ired at
your authorize d Aud i dea ler. •
App lies to ve hicle s: wit h ad apti ve light
Adaptive light defective f:.J
adaptive light defective
When this symbol Ji.., ill uminates, it means that adaptive light is
defective. Go to an author ized Audi dealer to h ave the headlig hts o r
the contro l unit for the adaptive lig ht repa ire d.•
Ignition lock malfunction ..c,
~ Ignit ion lock defective
If the sym bol i n the displ ay comes on, t here is a mal func tion in t he
elect ronic ignit ion lock . Please go to an authorized Audi dealer or
o th er qu alified w orkshop to have the mal func tio n re pa ir ed .•
A pp lies to ve hicl es: w it h Aud i d ri ve sele ct
Adaptive dampers~
Adaptive dampers: system malfunction
If the symbol in the dis pl ay comes on , there is a malfunction in the
adaptive dampers . P lease go to an au thorized Aud i dea le r or other
qualifie d wo rks hop to have t he malfunct io n repaire d.•
Vehicle care Technical data

Opening and closing
Opening the windows
- Press the switch to t he first stop and hold i t until t he
window reac hes th e desir ed posi tion.
- P ress the switc h briefly to the
second stop to automati­
cally open the window .
Closing the windows
-Pull t he sw itch to th e first stop and ho ld it until t he
w indow reac hes t he desired posi tion .
- P ull the sw itc h brie fly to t he
second stop to a uto matica lly
cl os e th e win dow.
Power window switches
© Drive r's door
© Passenger's doo r
© Left r ear door
@ Right re ar d oo r
You can open or close all the windows w it h the switch=> page
47,
fig . 40.
& WARNING
• Do not leave children unattended in the vehicle, especially with
access to vehicle keys . Unsupe rvised use of the keys can result in
starting of the engine and u se of vehicle sy stem s such as power
windows , etc. which could result in serious injury.
• Remember -you can still open or clo se the power windows for
about ten minutes after the ignition is switched off . Only when
either of the doors are opened are the power windows switched
off .
• Be careful when clo sing the windows . Check to see that no one
is in the way, or serious injury could result!
& WARNING (c on tinued )
• Always remove the ignition key whenever you leave your
vehicle.
• If y ou lo ck your vehicle from the outside, no one, e specially
children, should remain in the vehicle.
• Do not stick anything on the window s or the windshield that
may interfere with the dr iver's field of vision.
[I) Tips
• When you open the doors, the windows automatically lower about
1 0mm.
• After the ignition has been switc hed off, the w indows can still be
opene d or closed fo r ab out 1 0 min utes. The w indow reg ula tors are
not switched until t he d river's or passe nger's door is opened .•
Convenience opening/closing
The wind ows can be ope ned and closed with the mechan­
i c al key or the emergenc y key .
Fig. 41 K ey turn s for
o pe nin g an d cl osin g .._

Clear vision
when outside light is very low . This is to r emind you , the driver , to
s witch on the headlight s before it get s too dark.
• Canada models : inst rument p anel illumin ation will stay br ight
regardles s of the inten sity of ambient light. Alw ay s be aware of
changes in outs ide light conditions wh ile you are driving. Respond
in time to fading daylight by turning the light switch to po sition
io
(or "AUTO" if your car is equipped with this feat ure) to turn on your
headlights .•
A ppli es to ve hicles : wit h xe non h eadlights
Xenon headlights
After starting the engine, the xenon head lights are automat ically
adjusted to the load and ang le of t he vehicle (for e xamp le, dur ing
acce leration and brak ing) . This prevents oncom ing traffic from expe ­
r ienc ing unnecessary headlight glare from yo ur xenon head lights.
If the sy ste m is not opera ting p roperly, a warning symbol in t he Auto ­
Check Control is displayed~
page 35. •
App lies to vehicles : w ith adapti ve lig ht
Adaptive Light
Wh en driving around bends, the relevant ar ea of the road
is better illuminated .
Fig . 68 Adaptive lig ht
w hen driving
The benefit of adaptive light is that the curve and the edge of the road
are better illum inate d~ fig. 68. Dyn am ic a daptive light is con trolled
automatically, depend ing on ve hicle speed and steering whee l angle .
When driving around bends, the headlights are contro lled accord ing
t o s teer ing whee l angle . So t hat there is no bla ck ho le ahea d of the
vehicle , the two ma in beams pivot at d ifferent angles.
[I] Tips
The system works above a speed of about 6 mph (10 km/h) .•
Emergency flashers A
T h e eme rgency flash ers m akes ot her mot ori st s a ware
that you or y our vehicle a re in an eme rgency situation.
Fig. 69 Eme rgenc y
fla she r sw itch
Pr ess the swi tch~ => fig. 69 to tu rn the eme rgenc y
flash ers on or of f.
When the e merge ncy flashers are on, all fou r turn sig nals blink at the
same t ime. The turn signal indicator lights¢¢ in the i nstr ument
cl uste r, as well as the ligh t in the eme rge ncy flasher switch ~ blink
likewise . The emergency flashers also wo rk when the ignition is
t urned off. .,_

____________________________________________________ T_r_a _ n_ s_m_ i_ s _s_ i_ o _ n __ _
The selector lever must be in Nor P . If one o f the dr iv in g positions is
e n gag ed a saf ety s witch will preven t the engin e from b eing sta rt e d.
S ee also=>
page 106.
Be fore you move t he se lecto r lever from t he P position, yo u m ust
a lw ay s a ppl y the b rake pedal before and while depr ess ing the bu tton
in t he handle of the selector lever.
_& WARNING
• Unintended vehicle movement can cause serious injury.
- When the selector lever is
in a driving position, the vehicle
may creep, even at idle speed. Therefore do not release the
parking brake
or foot brake until you are ready to move,
because power is transmitted to the wheels as soon as a driving
position is engaged.
- Do not accelerate while selecting a driving position . At this
time the engine must be at idle speed so that undue stress is
not placed on the clutches in the transmission.
- Remember : · even when stopped briefly with the automatic
transmission
in " D", "S" or "R", engine power is being trans­
mitted to the wheels. Your vehicle could "creep " forward or
backward. When stopped, keep the brake pedal fully
depressed and use the parking brake if necessary to keep the
vehicle from rolling .
• If the selector lever is unintentionally moved into N while you
are driving, take your foot off the accelerator pedal and wait for
the engine to return to idle speed before selecting a driving posi­
tion.
• Never shift into "R" or "P " when the vehicle is in motion .
• Never get out of the d river's seat when the engine is running.
• If you must get out of the vehicle , move the selector lever
securely into the P position and apply the parking brake firmly .
• If the engine must remain running, never have any driving
position engaged when checking under the hood. Make sure the
selector lever has securely engaged and is locked in "P " with the
Controls and equip ­
ment Safety first
& WARNING (
cont inued)
parking brake firmly set=> page 272, "Engine compartment ".
Otherwise, any increase in engine speed may set the vehicle in
motion, even with the parking brake applied. •
App lies to vehicles : w it h auto mat ic t ransmiss ion
Selector lever positions
T his s ection d escrib es the s ele ct or l eve r posi tions and
drivin g ran ges.
Fig. 152 Di splay in
the instrum ent cluster:
selector lever In posi ­
tio n P
Th e sele ctor lever posi tion engaged appe ars ne xt to the se le ct or lever
as well as in the instr umen t cluster display .
P -Park
In this selector lev er position the transmiss ion is mecha nica lly
l oc ked. Engage
P only when the vehi cle is comple tely sto pp ed=> &
in " Driving t he automatic transmiss io n" on page 148.
T o sh ift in o r o ut of position P , yo u must first press an d hold the brake
peda l
and th en press t he r elease b utton in t he se lec to r l eve r hand le
wh ile moving the selector lever to or from
P. Yo u can s hif t out of thi s
posit ion on ly with t he ignit ion on . .,,
Vehicle care Technical data

1111....__T_ r_a _n_ s_m _ i_s _s _ i_o _n ___________________________________________________ _
Stopping
- Press a nd hold the brake pedal un til the vehicle has come
to a com plet e stop.
- Keep the brake pedal depressed so that the vehicle cannot
roll forward or backward w hile it is idli ng => & .
- Once sto pped,
do not depress t he accelerator pedal to rev
up the engine=> &.
Parking
- Press a nd hold th e br ake pedal u ntil th e v ehicle has com e
to a comp lete stop .
- S et the parki ng brakefir mly=>page
111, "Pa rking".
- Press an d hold the re lease button i n th e selector lever
handle, move the selector lever into
P and then let go of
the re lease button ~ & .
Your vehicle is equipped with a starting assist that a llows for eas ier
s t arting on in clines. The sys tem is activa ted w hen the brake ped al is
depressed for a
few seconds . After releasing the brake pedal, the
bra ke powe r is he ld for a moment to prevent the vehicle from ro lli ng
back when starting .
T he selector lever must be in Nor
P. If one of the driving positions is
engaged a safety switch will p reven t the eng ine from be ing started .
See also =>
page 106.
Before you move the selecto r lever from t he P posi tio n, yo u m ust
always app ly the brake peda l befo re and whi le depressing the button
in the handle of the selecto r lever .
& WARNING
• Unintended vehicle movement can cau se serious injury.
& WARNING (c on tinued )
-When the selecto r lever is in a dri ving pos ition, the vehicle
may creep , even at idle speed. Therefore do not relea se the
parking brake or foot brake until you are ready to move ,
becau se power is transmitted to the wheels a s soon as a driving
position i s engaged.
- Do not a ccelerate while selecting a driving p osition. At this
time the engine must be at idle sp eed so that undue stress is
not placed on the clutche s in the transmi ssion.
- Remembe r: • even when stopped briefly with the automatic
transmi ssion in "D ", "S " or "R ", engine power i s being trans·
mitted to the wheels . Your vehicle could "creep " forward or
backward . When stopped, keep the brake pedal fully
depressed and use the parking brake if necessary to keep the
vehicle from rolling .
- If the selector le ver is unintentionally moved into N while
y ou are driving , take your foot off the accelerator pedal and
wait for the engine to return to idle sp eed before selecting a
driving position.
- Never shift into "R " or "P " when the vehicle i s in motion .
- Never get out of the driver 's seat when the engine i s running .
- If you must get out of the vehicle , move the selector le ver
s ecurely into the P position and apply the parking brake firmly.
- If the engine must remain running , never have any driving
position engag ed when checking under the hood. Make sure
the selector lever has securely eng aged and is locked in "P"
with the parking brake firmly set=>
page 272, "Engin e
compartment ". Otherwise, any increase in engine speed may
s et the vehicle in motion, even with the parking brake
applied. •

Intelligent technology
--------------------------------------------------' "---.L==--
The system operates across the entire speed range in combination
with the ABS system. If the Anti-Lock Brake System (ABS) malfunc­
tions, the ESP will also shut down.
How the system works
The Anti-Lock Brake System (ABS), Electronic Differential Lock (EDL)
and the Anti-Slip Regulation System (ASR) are integ rated in the elec­
tronic stabilization program . In addition to the data provided by
these functions, the ESP control unit requires additional measure­
ment data provided by high performance sensors . The rotational
speed of the vehicle about its vertical axis, vehicle acceleration in the
fore-and-aft and lateral directions, the brake pressure, and the
steering angle are all measured .
Th e direction in which the driver wishes to travel is determined with
the aid of the steering angle and vehicle speed and is con tinually
compared with the actual behavior of the vehicle. If the two do not
match, for example, when the vehicle starts hydroplaning on a wet
road, ESP will automatically brake the appropriate whee l to correct
the problem.
The vehicle is then stabilized by the forces acting on the whee l during
brak ing.
If the vehicle is oversteering (the vehicle turns too sharply
and the rear wheels slide toward the outside of a curve), the brakes
are mainly applied on the wheel that is on the outside of the curve. In
the case of a vehicle that is
understeering (the vehicle does not turn
sharply enough and pushes out of a curve), the brakes are applied as
needed on the wheel that is on the inside of the curve or additionally
on the other wheels. An acoustic signal indicates when ESP brake
application cuts in=> &.
The system operates across the entire speed range in combination
with the ABS system =>
page 245. If the Anti- Lock Brake System
(ABS) malfunctions, the ESP will be out of action as well.
Activating
When you turn on the engine, ESP will automatically be activated and
w ill perform a self-test. As soon as the test is comp leted, the system
is in normal operating mode.
Controls and equip­
ment Safety first Vehicle operation
You can activate a
deactivated ESP or deactivated ESP/ ASR if required
by pressing the =>
page 240, fig. 214 => page 240, fig. 213 button.
When they are activated, the message
ESP/ ASR on appears briefly
in the display.
Deactivating
The ESP should normally be activated all the time. If necessary, you
can deactivate Anti-Slip Regulation (ASR) or the Electron ic Stabiliza ­
tion Program (ESP) by press ing the button =>
page 240, fig. 214 .
• Deactivating ASR: Tap the button . In certain exceptional s itua­
t ions (e.g. driving with tire chains), the Anti-Slip Regu lation (ASR) can
be deact ivated =>
page 242. The message ASR off appears in the
display as we ll.
• Deactivating ESP/ASR Press the button for more than 3 seconds .
With the ESP/ASR deactivated, the ESP check light comes on, see
=>
page 14. The message ESP switched off appea rs in the display as
well.
& WARNING
The Electronic Stabilization Program is nevertheless subject to the
laws of physics. It is particularly important to pay attention to
this fact on wet and slippery roads. It is therefore important that
you always adapt your driving to the condition of the road and
traffic conditions . Do not allow the increased safety provided by
the Electronic Stabilization Program system to lull you into
accepting additional safety risks.
u
Vehicle care Do-it-yourself service Technical data