2010 ASTON MARTIN V8 VANTAGE lock

Valve Train (03.09)
Engine (03.00)3-9-8 Workshop Manual Issue 5, January 2010
24. Install the special tool onto the flywheel.
Figure 36
25. Install and tighten the two screws that attach the special tool to the engine.
Figure 37
26. Install the engine timing cover (refer to procedure 03.10.AF - Engine Timing Cover).
Right Side Timing Chain Arm Assembly -
Remove and Install
Remove
1. Remove the engine timing cover. (03.10.AF - Engine Timing Cover). 2. Remove the two screws that attach the special tool to
the engine.
Figure 1
3. Remove the special tool from the flywheel.
Figure 2
4. Turn the crankshaft clockwise until the machined flat
areas on the camshafts are parallel to the face of the
cylinder head.
Figure 3
5. Install the special tool on the right side camshaft.
Repair Operation Time (ROT)
Note: If necessary, use special tool 303-530-04 with this
step.

Valve Train (03.09)
Engine (03.00)3-9-10 Workshop Manual Issue 5, January 2010
12. Install and tighten the two socket cap screws that attach the special tool to the engine.
Figure 10
13. Tighten the two socket cap screws that attach the teeth to the special tool.
Figure 11
14. Lower the vehicle.
15. Remove the three screws that attach the right side bush carrier for the Variable Camshaft Timing (VCT) to the
engine.
Figure 12
16. Remove the right side bush carrier for the VCT.
Figure 13
17. Loosen the two screws that attach the timing chain tensioner to the engine.
Figure 14
18. Release the ratchet lock on the timing chain tensioner and push the piston into the tensioner housing.
Figure 15

Valve Train (03.09)
Engine (03.00)3-9-12 Workshop Manual Issue 5, January 2010
2. Install and torque the special bolt that attaches the tensioner arm to the engine to 11 Nm (refer to
Figure 19).
3. Install the timing chain tens ioner (refer to Figure 18).
4. Install and torque the two bolts that attach the timing chain tensioner to the engine to 11 Nm (refer to
Figure 17).
5. Install the special tool on the exhaust camshaft sprocket.
Figure 22
6. Use the special tool to turn the exhaust sprocket counterclockwise until the chain is tight.
Figure 23
7. Release the pin from the ti ming chain tensioner and let
the tension piston gradually tension the timing chain.
Figure 24
8. Torque the two Torx bolts that attach the camshaft
sprockets to the camshafts to 20 Nm.
Figure 25
9. Torque the two Torx bolts that attach the camshaft sprockets to the camshafts 90 degrees more (refer to
Figure 25).
Note: You must use the special
tool to hold the timing chain
in the correct position during the subsequent two steps of
the procedure.
Note: Make sure that the tensio ner is fully operated but do
not use too much force.
Note: Make sure that you torque the bolt that attaches the
sprocket to the exhaust camsha ft first in the step that
follows.
Note: Make sure that you torque the bolt that attaches the
sprocket to the exhaust camsha ft first in the step that
follows.

Valve Train (03.09)
Engine (03.00)3-9-14 Workshop Manual Issue 5, January 2010
19. Remove the three screws that attach the special tool to the right cylinder head.
20. Remove the special tool from the right cylinder head.
21. Turn the crankshaft two full revolutions clockwise.
22. Use the applicable equipment to lift the vehicle and make it safe.
23. Install the special tool onto the flywheel.
24. Install and tighten the two screws that attach the special tool to the engine.
25. Install the engine timing cover (refer to procedure 03.10.AF - Engine Timing Cover).
RH/LH Secondary Tensioner Assembly -
Remove and Install
Remove
1. Remove the left and right primary timing chains (refer to Workshop Manual procedure 03.09.AM/03.09.AN/
03.09.CM/03.09.CN Chain - Timing Primary - LH/RH -
Renew).
2. Remove the two M12 Torx bolts that attach the inlet and exhaust camshaft sprockets to the camshafts (refer
to Figure 1).
Figure 1
3. Collect the spacer from the bolt on the exhaust camshaft.
4. Remove the two M6 bolts that attach the secondary timing chain tensioner to the cylinder head (refer to
Figure 2).
Figure 2
Caution: During the step that follows, if you feel any
increase in resistance, do not force the crankshaft. If
you do you can damage the en gine. If you cannot turn
the crankshaft, you must do the engine timing
procedure again.
Repair Operation Time (ROT)
Secondary Tensioner Assembly-
Renew LH-RHD
03.09.CR
Secondary Tensioner Assembly-
Renew RH-RHD
03.09.CS
WAR NI NG
DO NOT GET USED ENGINE OIL ON YOUR SKIN. USED ENGINE OIL CAN BE HARMFUL.
Repair Operation Time (ROT)
ItemCode
A0309252
A0309256

Valve Train (03.09)
Engine (03.00)
Issue 5, January 2010 Workshop Manual 3-9-15
5. Release and remove camshaft sprockets complete with timing chain and tensioner from camshafts (refer to
Figure 3).
Figure 3
6. Remove the secondary timing chain and tensioner from the sprockets (refer to Figure 4).
Figure 4
Install
1. Clean the camshaft sprockets and the tensioner.
2. Install the secondary timing chain and tensioner to the camshaft sprockets.
3. Install the secondary timing chain assembly onto the camshafts.
4. Install the spacer onto the exhaust Torx bolt.
5. Install the M12 exhaust Torx bolt to attach the exhaust camshaft sprocket. Do not tighten at this step.
6. Install the M12 inlet Torx bolt to attach the inlet camshaft sprocket. Do not tighten at this step.
7. Install and torque the two M6 bolts that attach the secondary tensioner.
8. Install the left primary timing chain guide.
9. Install and torque the M6 bolt that attaches the guide.
10. Make sure that the timing chain has no tension on the tensioner side of the timing chain.
11. Install the primary timing chain.
12. Install the tensioner blade for the primary timing chain.
13. Install and torque tighten the M6 bolt that attaches the tensioner blade. 14. Install the tensioner assemb
ly for the primary timing
chain.
15. Install and torque the two M6 bolts that attach the tensioner assembly.
16. Release the tension on the timing chain tensioner piston. Remove retaining special tool.
17. Install the timing chain tens ioning tool (303-532) into
the exhaust camshaft sprocket.
18. Apply a force to the tool (303-532) in a counterclockwise direction and torque the two M12
sprocket Torx bolts.
19. Remove the special tool (303-532).
20. Install the left and right prim ary timing chains (refer to
Workshop Manual procedure 03.09.AM/03.09.AN/
03.09.CM/03.09.CN Chain - Timing Primary - LH/RH -
Renew).
Right and Left Intake Camshaft - Remove
and Install
Remove
1. Remove the right and left secondary timing chain tensioners (refer to Workshop Manual procedure
03.09.AS/03.09.AR03.09.CS/03.09.CR Tensioner
Assembly - Secondary - RH/LH - Renew).
2. Remove the three bolts that attach the tool (303-530) to the cylinder head.
A0309254
A0309255
Caution
Apply an opposite force to the sprockets and chain while you tighten the sprocket bolts.
Repair Operation Time (ROT)

Valve Train (03.09)
Engine (03.00)
Issue 5, January 2010 Workshop Manual 3-9-19
5. Release and remove the camshaft sprockets complete with timing chain and tensione r from camshafts (refer to
Figure 3).
Figure 3
6. Remove secondary timing chain and tensioner from sprockets (refer to Figure 4).
Figure 4
Install
1. Clean the camshaft sprockets and tensioner.
2. Install the secondary timing chain and tensioner on to the camshaft sprockets.
3. Install the secondary timing chain assembly onto the camshafts.
4. Install the spacer onto the M12 exhaust Torx bolt.
5. Install the exhaust M12 Torx bolt to attach the exhaust camshaft sprocket. Do not tighten at this step.
6. Install the inlet M12 Torx bolt to attach the inlet camshaft sprocket. Do not tighten at this step.
7. Install and torque tighten the two M6 secondary tensioner bolts.
8. Install the left primary timing chain guide.
9. Install and torque the M6 bolt that attaches the left primary timing chain guide.
10. Make sure that there is no tension in the chain at the tensioner side.
11. Install the primary timing chain.
12. Install primary timing chain tensioner blade. 13. Install and torque the M6 bolt that attaches the
tensioner blade.
14. Install the primary timing chain tensioner assembly.
15. Install and torque tighten the two M6 bolts that attach the tensioner assembly.
16. Release tension on the timing chain tensioner piston, remove retaining special tool.
17. Install timing chain tensio ning tool (303-532) into
exhaust camshaft sprocket.
18. Apply a force to the tool (3 03-532) in an anti-clockwise
direction and torque tighten sprocket Torx bolts.
Remove special tool.
19. Install LH/RH primary timing chain (refer to Workshop
Manual procedure 03.09.AM/03.09.AN/03.09.CM/
03.09.CN Chain - Timing Primary - LH/RH - Renew).
RH/LH Secondary Tensioner Assembly-
Renew (with Engine Removed
)
Remove
1. Remove the LH/RH primary timing chain (refer to Workshop Manual procedure 03.09.BM/03.09.BN/
03.09.CM/03.09.CN Timing Chain - Primary - LH/RH -
Renew With Engine Removed).
2. Remove the two Torx head bolts, (there is a spacer on the exhaust Torx bolt), that attach the inlet and exhaust
camshaft sprockets to the camsh afts (refer to Figure 1).
Figure 1
A0309254
A0309255
Caution
Apply an opposite force to the sprockets and chain while you tighten the sprocket bolts
Repair Operation Time (ROT)
A0309252

Valve Train (03.09)
Engine (03.00)3-9-20 Workshop Manual Issue 5, January 2010
3. Remove the two bolts that attach the secondary timing chain tensioner to the cylinder head (refer to Figure 2).
Figure 2
4. Release and remove the camshaft sprockets complete with the timing chain and te nsioner from the camshafts
(refer to Figure 3).
Figure 3
5. Remove the secondary timing chain and tensioner from the sprockets (refer to Figure 4).
Figure 4
Install
1. Clean the camshaft sprockets and tensioner.
2. Install the secondary timing chain and tensioner to the camshaft sprockets. 3. Install the secondary timing chain assembly onto the
camshafts.
4. Install the spacer onto the M12 exhaust Torx bolt.
5. Install the exhaust M12 Torx bolt to attach the exhaust camshaft sprocket. Do not tighten at this step.
6. Install the inlet M12 Torx bolt to attach the inlet camshaft sprocket. Do not tighten at this step.
7. Install and torque tighten the two secondary tensioner bolts.
8. Install the left-side pr imary timing chain guide.
9. Install and torque the bolt that attaches the chain guide.
10. Make sure that the timing ch ain slack is on the tensioner
side of the timing chain.
11. Install the primary timing chain.
12. Install the tensioner blade for the primary timing chain.
13. Install and torque the bolt that attaches the tensioner blade.
14. Install the primary timing chain tensioner assembly.
15. Install and torque the two bolts that attach the primary chain tensioner.
16. Release the tension on the timing chain tensioner piston. Remove the retaining special tool.
17. Install the timing chain tensioning tool (303-532) on the exhaust camshaft sprocket.
18. Apply a force to the special tool (303-532) in a counterclockwise direction and torque the sprocket
Torx bolts. Remove the special tool.
19. Install the the left and right primary timing chain (refer to
Workshop Manual procedure 03.09.BM/03.09.BN/
03.09.CM/03.09.CN Timing Chain - Primary - LH/RH -
Renew With Engine Removed).
RH/LH Intake Camshaft Renew With
Engine Removed
Remove
1. Remove the left and right secondary timing chain tensioner (refer to Work shop Manual procedure
03.09.BS/03.09.BR Tensioner Assembly - Secondary -
RH/LH - Renew With Engine Removed).
2. Remove the three bolts that attach the tool (303-530) to
the cylinder head.
A0309256
A0309254
A0309255
Repair Operation Time (ROT)
ItemCode
Intake Camshaft-Renew LH03.09.BT
Intake Camshaft-Renew RH03.09.BV
WAR NI NG
DO NOT GET USED ENGINE OIL ON YOUR SKIN. USED ENGINE OIL CAN BE HARMFUL.

Valve Train (03.09)
Engine (03.00)
Issue 5, January 2010 Workshop Manual 3-9-25
13. Install and torque the M6 attachment bolt for the tensioner blade.
14. Install the tensioner assembly for the primary timing chain.
15. Install and torque the two M6 bolts that attach the tensioner assembly.
16. Release the tension on the piston of the timing chain tensioner.
17. Remove the retaining special tool.
18. Install the timing chain tensioning tool (303-532) into the exhaust camshaft sprocket.
19. Apply a force to the tool (303-532) in a counterclockwise direction and torque the M12
sprocket Torx bolts.
20. Remove the special tool.
21. Install the left and right primary timing chain (refer to Workshop Manual procedure 03.09.BM/03.09.BN
Timing Chain - Primary - LH /RH - Renew With Engine
Removed).
RH/LH Intake Camshaft Sprocket and
Housing Assembly-Renew
Remove
1. Remove the left and right pr imary timing chain (refer to
Workshop Manual procedure 03.09.AN/03.09.AM/
03.09.CN/03.09.CM Chain - Timing Primary - RH/LH -
Renew). 2. Remove the two M12 Torx bolts that attach the inlet
and exhaust camshaft sprockets to camshafts (refer to
Figure 1).
Figure 1
3. Collect the spacer from the bolt on the exhaust camshaft.
4. Remove the two M6 bolts that attach the secondary timing chain tensioner to the cylinder head (refer to
Figure 2).
Figure 2
Caution
Apply an opposite force to the sprockets and chain while
you tighten the sprocket bolts
Repair Operation Time (ROT)
A0309252
A0309253