2010 ASTON MARTIN V8 VANTAGE oil pressure

Power Conversion (03.11)
Engine (03.00)
May 2007 Workshop Manual 3-11-33
34. Note that piston grade number on crown and thick
flange on connecting rod faces to front of engine on LH
bank (B) (see Figure 17).
Figure 17
Installation
1. Clean cylinder bores.
2. Clean connecting rods,
3. Install pistons on connecting rods in their correct orientation, install circlip(s) (see Figure 18)
.
Figure 18
4. Correctly position ring gaps on pistons prior to installation.
5. Remove connecting rod bearing caps.
6. Install bearings in connecting rods and bearing caps.
7. Lubricate cylinder bores, pistons and rings with clean
engine oil.
8. Install special tools (303-535) to the connecting rod to prevent damage to crankshaft journal. 9. Install piston ring clamp to each piston in turn and install
in its respective cylinder bore. Remove piston ring
clamp (see Figure 19).
Figure 19
10. Lubricate crankshaft journals with clean engine oil.
11. Carefully pull each connecting rod into place on each crankshaft journal.
12. Install bearing caps to their relevant connecting rods. Install and torque tighten retaining bolts (x16).
13. Clean windage tray.
14. Install windage tray, install and torque tighten bolts (x8).
15. Clean old sealant from sump flange and engine bedplate.
16. Ensure that sump flange and mating face on engine bedplate are clean and dry.
17. Apply a continuous 3mm diameter bead of RTV sealant to sump flange as recommended.
18. Ensure that there are no gaps in sealant track.
19. Install sump, install and torque tighten bolts (x16) in the correct sequence.
20. Install A/C compressor mounting bracket, install and torque tighten Torx bolts (x4).
21. Lubricate and install new 'O' ring seals to oil pipes.
22. Install oil pipes in sump, install and torque tighten bolts (x2)
23. Install compressor, install and torque tighten bolts (x4).
24. Connect multiplug to A/C compressor.
25. Install LH and RH HEGO se nsor multiplug brackets to
sump. Install and torque tighten bolts (x4).
26. Secure harness clips (x6) in sump.
27. Connect multiplug to crankshaft timing sensor.
28. Connect multiplug to engine electric coolant temperature sensor.
29. Connect multiplug to oil pressure sensor.
Caution
Make sure the piston ring gaps are positioned at
different positions opposite the thrust side of the piston
before installation.
A0311332
A0311333
Caution
Install pistons into cylinder block with the

Power Conversion (03.11)
Engine (03.00)3-11-34 Workshop Manual May 2007
30. Clean oil scavenge pump and mating face on sump.
31. Install oil pump(s) drive sprocket.
32. Install new oil scavenge pump gasket, align on dowels
(x2).
33. Install chain onto oil scavenge pump sprocket.
34. Install oil scavenge pump, align to dowels (x2), Install and torque tighten bolts (x3).
35. Install chain onto oil pump drive sprocket.
36. Clean oil pressure pump and mating face on sump.
37. Install new gasket to sump, align to dowels (x2).
38. Position oil pressure pump, install chain on pump sprocket.
39. Install oil pressure pump, alig n to dowels (x2), Install and
torque tighten bolts (x3).
40. Install chain tensioner, install and torque tighten bolt, remove guide pin.
41. Install crankshaft timing sprocket.
42. Install cylinder head gaskets - engine set (see Workshop Manual procedure 03.01.HW Gasket - Cylinder Head -
Engine Set - Renew With Engine Removed).
Crankshaft Damper Pulley Assembly-
Renew
Removal
1. Remove engine drive belt (see Workshop Manual procedure 03.05.AB Belt - Engine Drive - Renew).
2. Raise vehicle on ramp.
3. Remove bolts (x2), inspection cover to lower crankcase, remove cover.
4. Install tool (303-1185) to restrain flywheel, install and tighten bolts (x2).
5. Install thrust button of tool (303 -1186) in crankshaft,
position tool in pulley, secure with bolts (x2). Tighten
centre bolt, withdraw pu lley from crankshaft.
6. Collect crankshaft pulley, locking ring and special tool thrust button.
7. Remove special tool from pulley. 8. Remove and discard O-ring seal from pulley (see
Figure 1).
Figure 1
Installation
1. Clean crankshaft pulley, locking ring and mating face on
crankshaft.
2. Lubricate and install new O-ring seal in crankshaft pulley.
3. Install crankshaft pulley, locking ring and new pulley bolt.
4. Torque tighten crankshaft pulley bolt. Remove special tool (303-1185) from crankcase.
5. Install inspection cover to lower crankcase, install and tighten bolts (x2).
6. Lower vehicle on ramp.
7. Install engine drive belt (see Workshop Manual procedure 03.05.AB Belt - Engine Drive - Renew).
Crankshaft Front Oil Seal-Renew
Removal
1. Battery isolation switch ‘OFF’.
2. Raise vehicle on ramp.
3. Remove crankshaft pulley (see Workshop Manual procedure 03.11.CP Pulley Assembly - Crankshaft
Damper - Renew).
Repair Operation Time (ROT)
Caution
The bolt thread in the cran kshaft must be cleaned out
before a new crankshaft pulley retaining bolt is installed
Repair Operation Time (ROT)
ItemCode
Crankshaft Front Oi l Seal-Renew 03.11.CQ
A0311321

Brake Actuation System (06.06)
Brake System (06.00)
May 2007 Workshop Manual 6-6-1
Brake System (06.00)
Brake Actuation System (06.06)
Description
Tandem Master Cylinder
The short-stroke tandem master-cylinder controls two
separate brake circuits which are jointly activated by the
brake pedal. In the event of a major leak in one system, the
other will still function. The two systems are supplied by a
common brake fluid reservoir.
A pressure sensor attached to the master-cylinder provides
the ABS / DSC module with brake pressure information. This
information informs the system how hard the driver is
braking and is used as an aid for the ABS / DSC to achieve
accurate brake pressure control.
Brake Fluid Reservoir
The brake fluid reservoir is mo unted directly on the tandem
master cylinder and secured with a pin. Two stub pipes, on
the base of the reservoir, locate into the primary and
secondary chambers of the tandem master cylinder.
An integral fluid-level switch is incorporated in the reservoir.
If the brake fluid level is low, the brake warning lamp in the
Driver Information Module (D IM) will illuminate and ‘LOW
BRAKE FLUID’ will be displayed in the message center right.
Specifications
Oils/Greases
Brake Fluid Castrol Response Super Dot 4
Torque Figures
DescriptionNm.
Master Cylinder Mount 25 (+/- 4)
Brake Pipe Unions 17
Brake fluid reservoir securing pin 4
Pressure Sensor 35 (+/- 2)

Anti-lock Braking System (ABS) (06.09)
Brake system (06.00)
Issue 4, November 2008 Workshop Manual 6-9-3
Engine Intervention
In the event of wheel-slip the ABS / DSC module calculates
the torque, which should be applied by the engine to reduce
the wheel-slip (this torque does not exceed driver demand).
Engine torque reduction is then requested from the PCM via
the CAN bus. The PCM, in response to these signals, reduces
engine torque by controlling the ignition and fuelling. A
traction control gearshift pattern is automatically selected
within the automatic transmission software whenever
traction control is active.
Brake Intervention
This function operates by increasing the pressure in the
brake caliper of the slipping wheel, by closing the separation
valve and the inlet valve of the non-slipping wheel and
running the modulator pump. This takes fluid from the fluid
reservoir via the non-actuated master cylinder and
pressurizes the brake caliper. The pressure is modulated at
the caliper via the inlet and outlet valves to achieve the
desired wheel-slip target to maximize traction.
ABS / DSC Circuit
Specifications
SR,05UR,05YR,0.5NR,0.5
WR,05NR,05
YG,05WG,05
YU,05WU,05
W,05N,05
W,0.5U,0.5R,0.5
P,0.5Y,0.5
B,0.5WG,0.5GB,0.5
B,0.5BG,0.5
GW,0.5
P,0.5
U,0.5
U,3.0
BK,1.0BK,1.0
P,0.35P,0.35P,0.35 U,3.0
WG,05YG,05
WU,05
SR,05UR,05YR,0.5NR,0.5
WG,05YG,05
WU,05
WG,05YG,05
WU,05YU,05YU,05YU,05Module-ABS
OBD2-Body (B)
Earth-Module ABSEarth-Module ABS
C1184-18C2410-6
Sensor-Brake Pressure
Sensor-Brake Pedal Travel
Sensor-Rear ABS-LH
C0746-7C0746-6
C0746-5
Switch-Brake Boost
Sensor-Yawrate / Acceleration
C2411-6C2411-5C2411-4
C2411-3
C0144-7C0144-3
C0144-2
Sensor-Front ABS-LH
Sensor-Front ABS-RH
C2410-10C2410-9
C2410-8
Sensor-Rear ABS-RH
C0746-4C0144-1C2410-7
C0877-7
K-LINESPL50-KL/FA
C0362-1C0434-1
C2444-2
SIGC2444-1
GND
C2444-3
SENSP
C2446-2
GNDC2446-1
SENSPT
C2446-3
SIG
C0501-47
GNDC0501-16
GND
C0501-2K-LINE
C0501-24
GND
C0501-31
PWM
C0501-30
NC
C0501-25
CAN HS-
C0501-28
SIGC0501-27
NO
C0501-29
CAN HS+C0501-6
CLUST_SP
C0501-17
PWR
C0501-5
GND
C0501-32BATT FEED
C0501-7
SENSPT
C0501-3 SIG
C0501-20 SIGC0501-19
GND
C0501-18 SENSP
C0501-4IGN FEED
C0501-46
F/L/GNDC0501-45
F/L/SIG
C0501-42
R/R/GNDC0501-43
R/R/SIG
C0501-36
R/L/SIG
C0501-34
F/R/SIGC0501-33
F/R/GND
C0501-1
BATT FEEDC0501-37
R/L/GND
C2448-5
C2448-3
C2448-2C2448-1
C2448-4
C1656-3 CLUS_SPC1656-2
CAN HS+C1656-1 CAN HS-
C1656-5
GND
C0516-2-C0516-1+
C0517-2
-C0517-1+
C0502-1
+
C0503-2 -C0503-1+
C0502-2 -
Sensor
Steering Angle
Sheet 61
F4
30.0 AmpsRelay 1
Underbonnet Fusebox
DIODE 1
F28
10.0 Amps
F20
30.0 Amps
F19
30.0 Amps
Earth
Steering Angle
Sensor
C0576-1
C0577-4C2608-1 VBATT
C0573-2
C0571-3
C0573-3
C0578-8SPL5-VIGN/FOR
C1672-5
VPWRC1672-8
GND
011-6-003
Oils/Greases
Brake FluidCastrol Response Super Dot 4
Torque Figures
DescriptionNm.lb. / ft.
Modulator to Bracket 5 4
Modulator / Bracket to body 9 7
Brake hose unions 17 1413
10.5
17 Nm. 17 Nm.
17 Nm.
14 Nm.
14 Nm. 14 Nm.

Manual Transmission (07.03)
Transmission (07.00)7-3-2 Workshop Manual Issue 5, January 2010
Specifications Maintenance
Transaxle Assembly - Remove for Access
and Install
Removal
1. Disconnect the battery ground cable.
2. Remove the rear undertray (refer to Workshop Manual procedure 01.02.PB - Rear Undertray).
3. Raise the vehicle and install straps to hold it to the lift (refer to Figure 1).
Figure 1
Type
Graziano AM803T transaxle with:
• Integrated Shifter Bellcrack System (Cable Operated)
• Integrated Reverse Switch
• Plate Type Limited Slip Differential
Synchronisers
Triple Cone Syncros on 1st and 2nd, double cone on all
other gears incl. reverse.
Lubrication
Pressure fed system with integrated pump driven by the
input shaft. Filter (filter is serviceable item).
Transaxle Oil
Shell Transaxle 75W/90 (very important that this is the
transaxle type, Do not use Shell Spirax 75W90)
Transaxle Quantity.
Coolant System Quantity. 4 ltr (7 pt / 4.2 US qts)
0.5 ltr (0.9 pt / 0.53 US qts)
Transaxle + Coolant
Quantity 4.5 ltr (7.9 pt / 4.6 US qts)
Gear Ratios
1st 2nd 3rd 4th 5th 6th
3.15:1 1.95:1 1.44:1 1.15:1 0.94:1 0.77:1 (upto VIN
C00525)
0.76:1 (VIN
C00526
Onwards)
Reverse
2.39:1
Differential Locking Ratio
10% Drive, 30% Coast
Torque Figures
DescriptionNm.lb. / ft.
Sump plug 49 36.5
LH Output shaft housing 10 7.5
Halfshaft 70 52
Differential Cover 35 26
Repair Operation Time (ROT)
ItemCode
Transaxle Assembly-Remove for
Access/Refit 07.03.AA
WAR NI NG
WHEN YOU LIFT THE VEHICLE ON A 'TWO POST' LIFT MAKE SURE THAT YOU USE A STRAP TO HOLD THE REAR END OF THE VEHICLE TO THE RAMP. IF YOU
DO NOT, THE VEHICLE CAN FALL OFF THE RAMP AND CAUSE PERSONAL INJURY OR DEATH.
WAR NI NG
THE EXHAUST SYSTEM WILL BE VERY HOT AFTER
OPERATION. LET THE EXHA UST COOL BEFORE YOU
DO WORK. IF YOU DO NO T, PESONAL INJURY CAN
OCCUR.

Fuel Tank and Lines (10.01)
Fuel (10.00)
May 2007 Workshop Manual 10-1-3
Fuel Tank
The fuel tank incorporates a single filler neck and check valve, internal fuel pump, internal fuel filter, a sender unit and an
‘on board refuelling vapour recovery’ system.
Fuel Pumps

)XHO3XPS
The modular fuel pump is immersed in the base of the fuel
tank. The pump can deliver up to 150 litres/hour. The in-
tank fuel line connects to the external line using a quick-fit
connector in the base of the fuel tank. During normal running, pressu
rised fuel from each fuel
pump passes from the tank, through an 3 micron in-tank fuel
filter to one of the two fuel rails on the engine.
Fuel temperature is measured on the primary fuel rail. If fuel
temperature becomes excessive, the fuel pressure is
increased to prevent fuel vaporisation (boiling).
Fuel pressure is measured by sensors on each fuel rail. The
fuel pressure to each rail is regulated as required by
continuously changing the run speed of the associated fuel
pump. Maximum pressure in the system is limited to 5.3 bar
by in-tank pressure regulators.
A constant head of fuel is maintained in the fuel pump
modules to ensure that the pumps cannot run dry in a ‘low
fuel’ situation.

)XHO3XPS
)XHO/LPLW9HQW9DOYH5ROO2YHU9DOYH
+LJK3UHVVXUH)HHG IURP5+63XPS )LOOHU1HFN
&KHFN9DOYH -HW3XPS/RZ3UHVVXUH
)HHGWRWKH6ZLUO3RW

Steering Gear (11.01)
Steering (11.00)
Issue 5, January 2010 Workshop Manual 11-1-3
Vehicle tends to pull
to one side when
driven on a level
surface. Incorrect tyre pressure. Adjust tyre pressure.
Incorrect tyre size.
Different tyre or tread type.
New tyre as required.
Vehicle is unevenly or excessively loaded. Adjust load evenly.
Incorrect toe adjustment. Adjust as required.
Damaged front or rear suspension
components. New suspension components.
Steering gear valve effort out of balance. Shift transmission into neutral while driving at no more than 30 miles/hour (50 km/h) and turn the
ignition to position I (engine ‘Off’-coasting).
a. If the vehicle does not pull to one side with the
engine off, install a new steering gear.
b. If the vehicle drifts with the engine off, ‘cross switch’ the front wheel assemblies.
Test at low speed due to directional tyres.
a. If the vehicle pulls to the opposite side, switch the wheels that were on the rear to the same
side on the front.
b. If the vehicle pull direction is not changed, check the front suspension components and
toe adjustments.
Check front and rear brakes for correct
operation. Adjust as required.
Check for bent rear suspension components
and for damaged coil springs in the front
suspension. New rear suspension components.
Check the rear suspension for loose or worn
suspension components. Tighten.
New components.
Incorrect underbody alignment. Check underbody alignment.
Feedback (whining
or knocking noises
in the steering gear)
Condition where
roughness is felt in
the steering wheel by
the driver when the
vehicle is driven over
rough surfaces. Loose or worn tie-rods. New steering gear.
Steering gear bolts loose or damaged. Tighten.
New bolts.
Loose suspension bushing , bolts or ball joints. Tighten.
New components.
Damaged steering column.
Loose Column bolts. New steering column.
Tighten bolts.
Power steering
pump or reservoir
leaks Overfilled system. Correct fluid level.
Damaged fluid cap. New fluid cap.
Loose or damaged hose fittings. Tighten.
New hose.
Leakage at power steering pump. New power steering pump.
Poor returnability of
the steering Incorrect tyre pressure. Check
and adjust tyre pressure.
Incorrect tyre size or ty pe. New tyre as required.
Steering column universal joints binding . New steering column.
Steering column shaft floor seal may be torn
and fouling I-shaft. New floor seal as required.
Binding or damaged tie-rods. New steering gear.
Damaged or worn front suspension
components. New front suspension components as required.
Incorrect toe adjustment. Adjust as required.
SymptomPossible CauseAction

May 2007 Workshop Manual 12-1-1
Climate Control (12.00)
Contents
Body Ventilation (12.01) ...................................... 12-1-2Air Intake & Distribution System............................ 1-2 Air Intake Actuator ................................................. 1-3
Air Mix Actuator .................................................... 1-3
Airflow Mode Actuator........................................... 1-4
Heater System (12.02) ......................................... 12-2-1 Maintenance ........................................................... 2-1 RHD/LHD Heater Unit (Including ECU)-Renew...... 2-1
Air Conditioning (A/C) System (12.03) ................ 12-3-1
Major Components................................................. 3-2 Refrigerant System ................................................. 3-3
Storing Refrigerant ................................................. 3-4
Handling Insufficient Refrigerant Level ................... 3-4
Handling Compressor Oil....................................... 3-4
Refrigeration Cycle................................................. 3-4
Specifications.......................................................... 3-5 Refrigerant and Lubricant ....................................... 3-5
Capacities .............................................................. 3-5
Torque Figures ....................................................... 3-5
Diagnostics ............................................................. 3-6 Electrical Connectors.............................................. 3-6
DTC Inspection ...................................................... 3-7
Single Fault Codes.................................................. 3-7
Multiple Fault Codes .............................................. 3-8
Maintenance ........................................................... 3-9 Connections .......................................................... 3-9
Recovery................................................................ 3-9
Evacuation ........................................................... 3-10
Charging .............................................................. 3-10
A/C System Testing............................................... 3-11
Leaks ................................................................... 3-12
System Pressure Fault Classification ...................... 3-12
Maintenance ......................................................... 3-13 Condenser-Renew ............................................... 3-13
Air Conditioning Compressor-Renew ................... 3-13
Blower Assembly-Renew ...................................... 3-14
Compressor to Condenser Tube
Assembly-Renew.................................................. 3-14
Troubleshooting ................................................... 3-16