2010 ASTON MARTIN V8 VANTAGE oil pressure

Air Conditioning (A/C) System (12.03)
Climate Control (12.00)
12-3-4 Workshop Manual May 2007
Storing Refrigerant
Handling Insufficient Refrigerant Level
Handling Compressor Oil
Refrigeration Cycle
Operation
1. The Compressor (1) dr aws low pressure, low
temperature, refrigerant vapour from the evaporator (5)
and compresses it, raising th e refrigerant pressure and
temperature.
2. This high pressure, hot, refrigerant vapour enters the condenser (2), where it is cooled by the flow of ambient
air and changes state into a cooler, high pressure liquid.
3. From the condenser, the liqu id passes into the receiver
drier (3) which has three functions:
• Removes moisture from the refrigerant using a desiccant
• Filters the refrigerant to remove system contaminants
• Stores the refrigerant to cope with varying system refrigerant demands
4. The filtered liquid refrigerant, still at high pressure, then enters the expansion valve (4). Here it passes through a
controlled orifice and emerges as an atomised liquid
spray. This has the effect of reducing the refrigerant
pressure and temperature. The cold refrigerant spray
now flows into the evaporator (5).
5. As refrigerant passes through the evaporator core, it cools the incoming airflow. Heat is absorbed by the
refrigerant, during this process and it once again changes
state, from an atomised cool liquid into a vapour. The
refrigerant vapour then returns to the compressor for the
cycle to be repeated.
An automatic safety valve is incorporated in the compressor,
which will open if the system pressure rises above 41 bar.
The valve will reseat when the pressure drops below 27,6
bar. When the safety valve is open, the compressor will 'free
Warning
The refrigerant container is highly pressurized. If it is subjected to high heat, it could explode, scattering metal fragments and liquid refrigerant that can
seriously injure personnel. Store refrigerant at
temperatures below 40
oC (104 oF).
Caution
If an insufficient refrigerant level is detected while
troubleshooting, do not char ge (add) the refrigerant.
Because an accurate amount of refrigerant cannot be
determined from the pressure indicated on the
recovery / recycling / rechar ging unit, never charge the
refrigerant.
Caution
If there is too much or to o little refrigerant from the
refilling, there may be secondary problems such as
damage to the refrigerant cycl e parts, or a decrease of
cooling performance. Therefore, if it is determined that the refrigerant level is insufficient, completely remove refrigerant from the refriger ant cycle and refill with
refrigerant to the specified amount.
Caution
Use only ND8 compressor oil for this vehicle. Using a PAG oil other than DENSO OIL8 compressor oil will damage the A/C compressor.
Caution
Do not spill the ND8 compressor oil on the vehicle. A drop of compressor oil on the vehicle surface can
damage the paint work. If oil gets on the vehicle, wipe it off immediately.
Caution
ND8 compressor oil has a high moisture absorption
efficiency. If moisture mixe s with the compressor oil,
the refrigerant system could be damaged. Ensure caps
are installed immediately afte r using the compressor oil
or removing refrigerant system parts to prevent moisture absorption.

 
 


+LJK3UHVVXUH+RW9DSRXU
+LJK3UHVVXUH&RRO/LTXLG
/RZ3UHVVXUH&ROG9DSRXU
/RZ3UHVVXUH+RW9DSRXU
&RPSUHVVRU
&RQGHQVHU
5HFHLYHU'ULHU
([SDQVLRQ9DOYH
(YDSRUDWRU
7ULQDU\6ZLWFK

Air Conditioning (A/C) System (12.03)
Climate Control (12.00)
May 2007 Workshop Manual 12-3-9
Maintenance
Assessment of the A/C system operating efficiency and fault
classification may be achieved by using the facilities on a
Recovery / Recycling / Recharging unit.
Follow the manufacturer's instructions implicitly and observe
all safety considerations.
Connections
Only use hoses with connectors which are dedicated to
HFC 134a charge ports.
Recovery
Read manufacture’s instructions and warnings before
completing any recovery / evacuating and charging
operations.
Warning
Under no circumstances should connections be made with the A/C system in operation or valves open. Should valves be open and a vacuum pump or
refrigerant container attached, an explosion could
occur as a result of high pressure refrigerant being forced back into the vacuum pump or container.
Warning
Handling liquid refrigerant is dangerous. A drop of
refrigerant on the skin can result in localized frostbite. When handling refrigerant, wear gloves and safety
goggles. If refrigerant sp lashes into the eyes,
immediately wash them with clean water and consult a doctor.
Caution
Do not attempt to adapt this unit for R-12 as an A/C
system failure will result. Recovery / Recycle /
Recharging equipment has sp ecial connections to avoid
cross contamination wi th R-12 systems.
The A/C unit’s overfill li mitation mechanism has been
calibrated specifically for use with the 50 lb. (23 Kg)
refillable refrigerant tank.
Run the A/C system for a few minutes before starting the
recovery procedure as this wil l enable more refrigerant to
be recovered. Turn the A/C system off before starting the
procedure.
Ensure the A/C system has pre ssure in it before beginning
the recovery process; if there is no system pressure there is
no refrigerant to recover.
Ensure that the oil drain valve is closed.
Caution
The Recovery / Recycling / Re charging unit relies on a
weighing mechanism to weight the quantity of oil
removed. Ensure that the Recovery / Recycle /
Recharging unit is not disturbed during the recovery procedure.

Air Conditioning (A/C) System (12.03)
Climate Control (12.00)
12-3-10 Workshop Manual May 2007
1. Connect an R-134a Recovery / Recycling / Recharging
unit to the vehicle A/C system.
2. Follow the Recovery / Recycling / Recharging unit manufacturer’s instructions to evacuate the A/C system.
Evacuation
The removal of unwanted air and moisture, is critical to the
correct operation of the A/C system. Moisture in the system
can be highly destructive and may cause internal blockages
due to freezing; water suspended in the lubricating oil will
damage the compressor. Once the A/C system has been
dismantled, or the refrigerant charge recovered, all traces of
moisture must be removed before charging.
Read manufacture’s instruct ions and warnings before
completing any Recovery / Recycling / Recharging
operation.
1. Connect an R-134a Recovery / Recycling / Recharging unit to the vehicle A/C system.
2. Follow the Recovery / Recycling / Recharging unit manufacturer’s instructions to evacuate the A/C system.
Charging
Read manufacture’s instruct ions and warnings before
completing any Recovery / Recycling / Recharging
operation.
1. Connect an R-134a Recovery / Recycling / Recharging unit to the vehicle A/C system.
2. Follow the Recovery / Recycling / Recharging unit manufacturer’s instructions to charge the A/C system.
Compressor oil may be drawn ou
t during this process, take
note of the quantity recovered so that it may be replaced.
It is recommended that initiall y only the high-side valve be
opened at the start of the pr ocedure. After a short time a
small depression should be seen on the low-side, at which
point the low-side valve may be opened and the evacuation
process completed. If a vacuum is not registered on the
low-side, it may indicate that the expansion valve is
permanently closed or that th e system is blocked. This
simple check may save time and effort when the system is
recharged.
Caution
Do not exceed the specificat ion when charging the A/C
system with refrigerant. Doing so will decrease the
efficiency of the A/C unit or damage the refrigeration cycle parts.
Caution
Always start the charging of refrigerant from the high-
pressure side. If charging st arts from the low-pressure
side, vanes of the A/C compressor will not be released and abnormal noise may result.

Air Conditioning (A/C) System (12.03)
Climate Control (12.00)
12-3-12 Workshop Manual May 2007
Leaks
Faults associated with low refrigerant charge weight and low pressure may be caused by leakage. Leaks traced to
mechanical connections may be caused by torque relaxation or joint face contamination. Evidence of oil around such
areas is an indicator of leakage.
Leak Detection
Fluorescent Tracer Dye - A fluorescent tracer dye is incorporated into th e refrigeration system and can be checked for
non-apparent leaks by scanning with a high intensity ultraviolet lamp. The location of leaks can be pinpointed by the bright
yellow glow of the tracer dye.
Automatic Refrigerant Leak Detector - (various manufacturers) Hand-held, portable, battery operated leak detector.
Place in and around A/C system to detect refrigerant leaks.
System Pressure Fault Classification
This table should be used in conjunction with the graphical representations of 'High side' pressure / ambient temperature
and 'Low side' pressure / evaporator temperature. Caution
Observe ALL safety precautions associ ated with ultraviolet equipment.
If erratic or unusual gauge movements occur, check the equipment against known Recovery / Recycling / Recharging unit
gauges.
Low side
gauge readingHigh side
gauge reading
Fault
Cause
Normal Normal Discharge air initially c ool then warms up Moisture in system
Normal to low Normal As above As above
Low Low Discharge air slightly cool Refrigerant charge low
Low Low Discharge air warm Refrigerant charge very low
Low Low Discharge air slightly cool or frost build up at expansion valve Expansion valve stuck closed
Low Low Discharge air slightly cool, sweating or frost after point of restriction Restriction in High side of system
High Low Compressor noisy Defective compressor reed valve
High High Discharge air warm and high side pipes hot Refrigerant charge high or inefficient
condenser cooling due to air flow blockage or
engine cooling fans not working
High High Discharge air warm
Sweating or frost at evaporator Expansion valve stuck open

Air Conditioning (A/C) System (12.03)
Climate Control (12.00)
May 2007 Workshop Manual 12-3-17
Symptom (7)DescriptionPossible Cause
Air from vents not cold enough. Magnetic clutch operates but A/
C system malfunctions. • Drive belt fault
• Fault in blower unit or condenser
• Fault in Receiver / Drier or expansion valve
(valve closes too much)
• Fault in refrigerant lines
• A/C compressor system fault, insufficient compressor oil
• Over filling of compressor oil, fault in expansion valve or A/C unit air mix link system
Symptom (8)Possible Cause
No cool air. Magnetic clutch does not
operate. • Fault in PCM A/C cut control system
• Fault in A/C Module
• Fault in refrigerant pressure switch
• Fault in PCM (A/C signal)
• Fault in PCM (IG1 signal)
• Fault in A/C compressor
•Fault in A/C relay
• Fault in Evaporator Temperature Sensor
Shake the wiring harness and connectors wh ile performing the inspection to discover whether poor contact points are the
cause of any intermittent malfunctions. If there is a problem, check to make sure connectors, terminals and wiring harnesses
are connected correctly and undamaged.
Symptom (9)Possible Cause
Noise while operating A/C
system. Noise from magnetic clutch, A/C
compressor, hose or refrigerant
line. • Magnetic clutch operation noise
• A/C compressor slippage noise
• Hose or refrigerant line interference noise

Instrument Cluster (13.01)
Information, Gauge and Warning (13.00)
May 2007 Workshop Manual 13-1-3
Information and Warning Lamps
Name / FunctionDescriptionSymbolInput SignalPower
On Check
General Warning
– Amber/Red Controlled internally by the DIM. It is used in conjunction with
several text messages to indicate information to the driver. Internal
SRS (Airbag) Controlled externally by the SRS module and indicates a fault in the SRS module. CAN Yes (5 Seconds)
High Engine
Coolant Temp. This tell tale is controlled internally by the DIM. Activated
when the engine coolant temperature signal from the CAN bus
reaches a pre defined value. (The
actual symbol is not lit, only
the red LED.) CAN
DSC Controlled externally by the ABS/DSC module. Indicates when the system is in operation or when it is turned off. The tell tale
is triggered by a CAN signal. CAN Yes (5 Seconds)
ABS Controlled externally by th e ABS/DSC module. Indicates a
fault in the ABS system. The tell tale is triggered by a CAN
signal. CAN Yes (5 Seconds)
Rear Fog Lights Controlled externally by the SRS module. Indicates that the
rear fog lights are turned on. The tell tale is triggered by a CAN
signal. CAN Yes (5 Seconds)
Seat Belts Controlled externally by the CEM. Indicates that the seat belts are not fastened properly. The tell tale is triggered by a CAN
signal. CAN Yes (5 Seconds)
Brake (General) Controlled externally by either the CEM or the ABS / DSC module. It indicates low brake fluid level, brake fault and park
brake. The tell tale is triggered by two low side inputs or a CAN
signal. Low side x 2
and
CAN Ye s ( 5 S e c o n d s )
Side Lights Controlled externally by th e CEM. Indicates that the side lights
are on. High side
Oil Pressure Controlled exte rnally by the PCM. Indicates low oil pressure.
The tell tale is triggered by a CAN signal. CAN Yes (5 Seconds)
Battery Charge Controlled externally by th e CEM. Indicates that the alternator
is no longer charging the battery properly. The tell tale is
triggered by a CAN signal. CAN Yes (5 Seconds)
Fuel Level Low Controlled internally by the DIM. Activated when the fuel level drops below a pre defined value. The fuel information is
provided from the CAN bus. The symbol is not lit, only the
amber LED. CAN
Turn Left/Right Controlled externally by th e CEM. The tell tale is triggered by a
CAN signal. CAN
High Beam Controlled externally by the CEM. Indicates that the high beam is switched on. The tell tale is triggered by a CAN signal. CAN
Check Engine Controlled externally by the PCM. Indicates a fault in the engine management system. The te ll tale is not connected to
the microprocessor. Low side
Tyre Pressure Controlled by the DIM. In dicates a low or rapid change in the
tyre pressure or a tyre pressure monitoring system fault. Low side Yes (5 Seconds)
Not Used
PATS Controlled externally by the PCM. Indicates key acceptance status. Low side

Wiring and Circuit Protection (18.01)
Electric Distribution/Electronic Control (18.00)
May 2007 Workshop Manual 18-1-23
12. Remove nuts (x8) securing RH exhaust manifold to cylinder head, remove ma nifold (see Fig. 5).
13. Remove coil covers (x2).
14. Disconnect multiplugs (x8) to ignition coils (see Fig. 6).
15. Disconnect multiplug to VVT solenoids (x2).
16. Disconnect multiplugs (x8) to Injectors (see Fig. 7).17. Disconnect multiplug (x1) fu
el rail pressure sensor (see
Fig. 8).
18. Remove bolt (x1) purge valve pipe to RH support bracket.
19. Release engine harness from RH support bracket (clips x3).
20. Remove cam cover nut (x1) and bolts (x2) and remove RH support bracket.
21. Release heater hose from heater hose bracket.
22. Release vacuum pipe from heater hose bracket clips (x2).
23. Release harness from heater hose bracket clips (x3).
24. Remove cam covers nuts (x2) and release RH heater hose bracket.
25. Disconnect multiplug (x1) alternator (see Fig. 9).
Fig. 5
Fig. 6
Fig. 7
$
$
$
Fig. 8
Fig. 9
$
$

Wiring and Circuit Protection (18.01)
Electric Distribution/E lectronic Control (18.00)
18-1-24 Workshop Manual May 2007
26. Disconnect multiplugs (x2) oil pressure and temperature
switches (see Fig. 10).
27. Disconnect multiplug (x1) starter motor (see Fig. 11). 28. Disconnect multiplug (x1) cr
ankshaft sensor (see Fig.
12).
29. Release HEGO engine harn ess connections (x4) from
mounting brackets.
30. Release engine harness from clips (x10) and move harness aside.
31. Release VVT harness clip to cam cover.
32. Disconnect multiplug (x1) inlet air temperature sensor.
33. Disconnect multiplug (x1) throttle body.
34. Disconnect multiplug (x1) condenser.
35. Release engine harness from LH heater hose bracket.
36. Remove cam cover nut (x1) and bolts (x2) and remove
LH support bracket.
37. Release servo hose from bracket clip.
38. Release heater hose fr om heater hose bracket.
39. Remove cam covers nuts (x 2) and release heater hose
bracket.
40. Disconnect breather hose from manifold.
41. Remove bolts (x10) inlet manifold.
42. Release engine harness from clips (x15) and move harness aside.
43. Disconnect multiplugs (x2) from CMP sensors.
44. Disconnect multiplug (x1) air control valve solenoid
connection.
Fig. 10
Fig. 11
$%
$
Fig. 12
$