Page 794 of 947
Squeaks and Rattles Repair Manual
Page 10 of 21 Issue 3
Figure 3
4. Remove the centre-stack instrument panel (panel).
5. Put the panel on a work bench that has protective material to prevent damage.
6. Remove the screw that attaches the locating peg br acket to the veneer bezel (refer to Figure 4).
Figure 4
7. Replace the installed locating peg (type “A”) with th e new flocked peg (type “B”) (refer to Figure 5).
Figure 5
8. Install and torque the screw to 2 Nm.
9. Put the panel into position (refer to Figure 6).
Page 796 of 947
Squeaks and Rattles Repair Manual
Page 12 of 21 Issue 3
13. Push the centre-stack instrument panel until it engages with the four retaining clips.
Page 797 of 947
Squeaks and Rattles Repair Manual
July 2010 Page 13 of 21
Sat-Nav Chatter
SRO: 19.07.CG
Safe VINs: DBS - E01840, DB9 - A12676, V8 Vantage - C13743
Repair:
Pre safe VIN
CAUTION:
BE CAREFUL WHEN YOU RELEASE THE INSTRUMENT PANEL VENEER BEZEL. THE SURFACE FINISH CAN BE EASILY DAMAGED.
1. Release the four clips that attach the centre-s tack instrument panel (refer to Figure 1).
Figure 1
2. Disconnect the electrical connectors from each of the fo ur transmission control switches (refer to Figure 2).
Figure 2
3. Disconnect the electrical connector from the igni tion start/stop switch (refer to Figure 3).
Page 798 of 947
Squeaks and Rattles Repair Manual
Page 14 of 21 Issue 3
Figure 3
4. Remove the centre-stack instrument panel (instrument panel) (refer to Figure 4).
Figure 4
5. Put the instrument panel on a work bench that has protective material to prevent damage.
6. Release the sat-nav top panel.
7. Remove the spring type “A” (refer to Figure 5).
8. Install the new spring type “B” in the top panel (refer to Figures 5 and 6).
Note: The wire of the spring has a larger diamet er and the spring has a different shape.
Figure 5
Page 799 of 947
Squeaks and Rattles Repair Manual
July 2010 Page 15 of 21
Figure 6
9. Install the sat-nav top panel.
10. Put the instrument panel into po sition (refer to Figure 7).
Figure 7
11. Connect the electrical connector to ignition start/stop switch (refer to Figure 8).
Figure 8
12. Connect the electrical connectors to each of the four transmission control switches (refer to Figure 9).
Page 800 of 947
Squeaks and Rattles Repair Manual
Page 16 of 21 Issue 3
Figure 9
13. Make sure that the heater vents are correctly aligned.
14. Push the centre-stack instrument panel until it engages with the four retaining clips.
Page 801 of 947
Squeaks and Rattles Repair Manual
July 2010 Page 17 of 21
Sat-Nav Rattle (Loose in the aperture)
SRO: 19.07.CJ
Safe VINs: DBS - E01610, DB9 - A12546, V8 Vantage - C13503, V12 Vantage - S00185
Repair
CAUTION:
BE CAREFUL WHEN YOU RELEASE THE INSTRUMENT PANEL VENEER BEZEL. THE SURFACE FINISH CAN BE EASILY DAMAGED.
1. Release the four clips that attach the centre-s tack instrument panel (refer to Figure 1).
Figure 1
2. Disconnect the electrical connectors from each of the fo ur transmission control switches (refer to Figure 2).
Figure 2
3. Disconnect the electrical connector from the igni tion start/stop switch (refer to Figure 3).
Page 802 of 947
Squeaks and Rattles Repair Manual
Page 18 of 21 Issue 3
Figure 3
4. Remove the centre-stack instrument panel (panel) (refer to Figure 4).
Figure 4
5. Put the panel on a work bench that has protective material to prevent damage.
6. Remove the screws that attach the left and right navi gation door hinge brackets to the panel. Remove the
brackets (refer to Figure 5).
Figure 5
7. Remove the hinge bracket gear from the le ft hinge bracket (refer to Figure 6).
